Comparison of low and high pressure infiltration regimes on the density and highly porous microstructure of ceria ecoceramics made from sustainable cork templates

Cork templates were used to produce lightweight bulk biomimetic ecoceramic (environmentally conscious ceramic) monoliths. Bulk/monolithic ceramics are vital for many applications, i.e. energy materials and fuel cells. Using simple and flexible, aqueous green-chemistry procedures, for the first time the influence of infiltration regime, number of infiltration cycles and sintering temperature on ecoceramic density and microstructure was studied. This lightweight three-dimensionally ordered macroporous (3DOM) CeO2 preserved the hexagonal cellular structure of cork, but unlike the wood, the rear cell walls were open, greatly increasing open porosity. Higher sintering temperatures (1600 instead of 1000 °C) were required to produce cm size monolithic ecoceramics mechanically strong enough to be handled. The infiltration regime and number of infiltration cycles affected density and porosity. Lower infiltration pressure led to higher porosity ecoceramics (3.3–5.7%), which may favour catalytic performance, showing the possibility of tailoring porosity and specific surface area by modifying the number of infiltration cycles

Geopolymer foams: An overview of recent advancements

Geopolymer foams (highly porous materials) have emerged as one of the most exciting materials over the past few years due to their remarkable properties, low cost and green synthesis protocol, enabling their use in various high added-value applications. Review papers on porous geopolymers are uncommon, and the emphasis has been given to materials processing and properties, while the applications were only briefly addressed. This review aims to fill this gap by presenting a comprehensive literature survey and critical analysis of the most recent and exciting research carried out on geopolymer foams. Up to now, these bulk-type (not powders) materials have been mainly considered as thermal and acoustic insulators. However, besides addressing their use as building material, this review also shows that their use in less investigated, but environmentally and economically relevant applications (e.g. bulk-type adsorbents, pH buffering agents and catalysts), is feasible and might ensure performance and technical advantages over their powdered counterparts. The limitations, challenges and future prospects associated with the different applications are presented. This review shows the remarkable potential of geopolymer foams in high added-value applications, far beyond their historical use as Portland cement replacement, which may encourage the widespread technological use of these materials

Biomimetic cork-based CeO2 ecoceramics for hydrogen generation using concentrated solar energy

Naturally occurring and sustainable materials can be used as a template to create biomimetic/biomorphic ceramics, known as Ecoceramics (environmentally conscious ceramics). In this work, cork was chosen as template to produce novel ceria (CeO2) ecoceramics, for applications in water splitting for H2 production via direct concentrated solar thermochemical fuel production (TCFP). The cork powder was pyrolised at 900 °C and the resulting carbon skeleton was infiltrated with an aqueous CeO2 precursor, and then heated at 1000 °C for 2 h to produce the ecoceramic. The cellular structure of the cork was maintained, with hexagonal cell dimensions of 20-30 μm in diameter, but the grains were nanoscale at ≤100 nm. XRD data confirmed that CeO2 was the only crystalline phase obtained. An important feature was that, while the rectangular side walls were maintained to hold the three-dimensionally ordered macroporous (3DOM) cellular cork structure, the rear hexagonal walls were pierced repeatedly through the structure, unlike in the original cork structure, which will allow gasses such as H2 to permeate well into the structure, greatly increasing the reactive area available for catalysis. The next step will be to test the capabilities of both the regular, porous 3DOM structure and the nanoscale grains for thermochemical water splitting to produce hydrogen under direct concentrated solar energy

Nanostructured titanium dioxide coatings prepared by Aerosol Assisted Chemical Vapour Deposition (AACVD)

Titanium dioxide is a compound of great interest, due to its functional properties; one of its most important uses is as a photocatalyst. TiO2 coatings can be deposited using different techniques. Aerosol Assisted Chemical Vapour Deposition (AACVD) is particularly interesting, as high temperature or pressure are not necessary to generate the gaseous precursors. Furthermore, by carefully choosing the deposition conditions (i.e. deposition temperature, solvent), it is possible to obtain deposits with different morphology and, consequently, different functional properties. In this paper we present the synthesis of titanium dioxide coatings with AACVD using complexes between titanium isopropoxide (TIPP) and acetyl acetone (acac) as precursors. Deposition experiments were performed using different ratios of TIPP to acac, to assess the effect on the composition of the coatings, their morphology and photocatalytic activity. Results showed that the use of acac led to nanostructured titanium dioxide (nanoparticles of about 10−25 nm diameter). Raman analysis showed the presence of both anatase and rutile phases. XPS analysis indicated the presence of residual carbonaceous species in the coatings; despite this, they displayed photocatalytic properties similar or superior to AACVD films without carbon. Photocatalytic tests, performed measuring the Formal Quantum Efficiency (FQE) and the Formal Quantum Yield (FQY) in the degradation of resazurin, showed that a acac:TIPP ratio equal to 1 led to the material with the highest performance, as the FQE value was about three times higher than that for the coating prepared with TIPP alone. Overall the complexes between TIPP and acac are promising precursors for the AACVD technique, leading to nanostructured coatings with enhanced performance

Studies of structural, magnetic and dielectric properties of X-type Barium Zinc hexaferrite Ba2Zn2Fe28O46 powder prepared by combustion treatment method using ginger root extract as a green reducing agent

Various quantities of ginger (Zingiber officinale) root extract were used to prepare X-type Barium–Zinc hexaferrite with the chemical composition Ba2Zn2Fe28O46. The powders were prepared using a combustion treatment method, being pre-heated at 550 °C for 4 h with the ginger as a fuel, followed by final heating to 900 °C for 5 h and natural cooling to room temperature to obtain Ba2Zn2Fe28O46 hexagonal ferrite powder. The phase composition of heated powder samples was investigated by X-ray diffraction (XRD), indicating the formation of a mixture of X-type and hematite (α-Fe2O3). Up to 82.6%, X-ferrite was formed at 900 °C with 52.5 g of ginger root extract. Dielectric analysis of the prepared samples shows the frequency-dependent phenomena. All samples were hard magnets, with coercivity values (HC) between 262.2 and 318.3 kA m−1, and squareness ratios > 0.5. The sample prepared with 52.5 g ginger root extract possesses the highest value of saturation magnetisation (MS = 33.87 Am2 kg−1) in comparison with the other prepared samples. Therefore, ginger was shown to be a useful natural plant extract as a reducing fuel for the low-temperature synthesis of X-ferrites. The sample prepared with 35 g ginger root extract shows a broad loss tangent resonance peak between 10 kHz and 100 kHz, while other samples show loss tangent resonance peaks between 300 kHz and 2 MHz frequency range

Highly efficient lead extraction from aqueous solutions using inorganic polymer foams derived from biomass fly ash and metakaolin

This work reports a simple and safe, but powerful, route to depollute lead-containing aqueous solutions. Inorganic polymer foams (cm-size) were used as bulk-type adsorbents. The influence of the specimens' porosity and activator molarity on the foams' physical properties and on their lead extraction ability was studied. Then, the best performing samples were deeply evaluated as lead adsorbents by studying the impact of pH, lead concentration, contact time, ionic strength and solution volume. Lead sorption kinetics is strongly affected by the pollutant concentration, pH and the solution ionic strength. Under the most favourable conditions the foams showed an impressive removal capacity (105.9 mg/g at pH 5, 23 °C, C0 = 800 ppm, deionised water), surpassing all other reported values on the use of bulk-type inorganic polymers. The foams’ lead uptake is 2.3 times higher than the previous best performing bulk-type specimens (mm-size spheres), and sorption is 12.5–15 times faster. The foams can be easily regenerated using mild acidic conditions, and then reused as adsorbent, suggesting that the main adsorption mechanism is ion exchange

Studies of structural, magnetic and dielectric properties of X-type Barium Zinc hexaferrite Ba2Zn2Fe28O46 powder prepared by combustion treatment method using ginger root extract as a green reducing agent

Various quantities of ginger (Zingiber officinale) root extract were used to prepare X-type Barium–Zinc hexaferrite with the chemical composition Ba2Zn2Fe28O46. The powders were prepared using a combustion treatment method, being pre-heated at 550 °C for 4 h with the ginger as a fuel, followed by final heating to 900 °C for 5 h and natural cooling to room temperature to obtain Ba2Zn2Fe28O46 hexagonal ferrite powder. The phase composition of heated powder samples was investigated by X-ray diffraction (XRD), indicating the formation of a mixture of X-type and hematite (α-Fe2O3). Up to 82.6%, X-ferrite was formed at 900 °C with 52.5 g of ginger root extract. Dielectric analysis of the prepared samples shows the frequency-dependent phenomena. All samples were hard magnets, with coercivity values (HC) between 262.2 and 318.3 kA m−1, and squareness ratios > 0.5. The sample prepared with 52.5 g ginger root extract possesses the highest value of saturation magnetisation (MS = 33.87 Am2 kg−1) in comparison with the other prepared samples. Therefore, ginger was shown to be a useful natural plant extract as a reducing fuel for the low-temperature synthesis of X-ferrites. The sample prepared with 35 g ginger root extract shows a broad loss tangent resonance peak between 10 kHz and 100 kHz, while other samples show loss tangent resonance peaks between 300 kHz and 2 MHz frequency range.publishe