Superconductivity for Magnets

The present state of development of a series of industrial superconductors is reviewed in consideration of their future applications in high field accelerator magnets, with particular attention on the material aspect. The discussion is centred on Nb3Sn and MgB2, which are industrially available in a round wire configuration in kilometre lengths and are already envisaged for use in the LHC Upgrade (HL-LHC). The two systems Bi-2212 and R.E.123 may be used in magnets with even higher fields in future accelerators: they are briefly described.Comment: 21 pages, contribution to the CAS-CERN Accelerator School: Superconductivity for Accelerators, Erice, Italy, 24 April - 4 May 2013, edited by R. Baile

Transport Properties and Exponential n-values of Fe/MgB2 Tapes With Various MgB2 Particle Sizes

Fe/MgB2 tapes have been prepared starting with pre-reacted binary MgB2 powders. As shown by resistive and inductive measurements, the reduction of particle size to a few microns by ball milling has little influence on Bc2, while the superconducting properties of the individual MgB2 grains are essentially unchanged. Reducing the particle size causes an enhancement of Birr from 14 to 16 T, while Jc has considerably increased at high fields, its slope Jc(B) being reduced. At 4.2K, values of 5.3*10^4 and 1.2*10^3 A/cm^2 were measured at 3.5 and 10 T, respectively, suggesting a dominant role of the conditions at the grain interfaces. A systematic variation of these conditions at the interfaces is undertaken in order to determine the limit of transport properties for Fe/MgB2 tapes. The addition of 5% Mg to MgB2 powder was found to affect neither Jc nor Bc2. For the tapes with the highest Jc values, very high exponential n factors were measured: n = 148, 89 and 17 at 3.5, 5 and 10T, respectively and measurements of critical current versus applied strain have been performed. The mechanism leading to high transport critical current densities of filamentary Fe/MgB2 tapes based on MgB2 particles is discussed.Comment: Presented at ICMC 2003, 25-28 May 200

A Review of the Properties of Nb3Sn and Their Variation with A15 Composition, Morphology and Strain State

This article gives an overview of the available literature on simplified, well defined (quasi-)homogeneous laboratory samples. After more than 50 years of research on superconductivity in Nb3Sn, a significant amount of results are available, but these are scattered over a multitude of publications. Two reviews exist on the basic properties of A15 materials in general, but no specific review for Nb3Sn is available. This article is intended to provide such an overview. It starts with a basic description of the Niobium-Tin intermetallic. After this it maps the influence of Sn content on the the electron-phonon interaction strength and on the field-temperature phase boundary. The literature on the influence of Cu, Ti and Ta additions will then be briefly summarized. This is followed by a review on the effects of grain size and strain. The article is concluded with a summary of the main results.Comment: Invited Topical Review for Superconductor, Science and Technology. Provisionally scheduled for July 200

Effects of Neutron Irradiation on Pinning Force Scaling in State-of-the-Art Nb3Sn Wires

We present an extensive irradiation study involving five state-of-the-art Nb3Sn wires which were subjected to sequential neutron irradiation up to a fast neutron fluence of 1.6 * 10^22 m^-2 (E > 0.1 MeV). The volume pinning force of short wire samples was assessed in the temperature range from 4.2 to 15 K in applied fields of up to 7 T by means of SQUID magnetometry in the unirradiated state and after each irradiation step. Pinning force scaling computations revealed that the exponents in the pinning force function differ significantly from those expected for pure grain boundary pinning, and that fast neutron irradiation causes a substantial change in the functional dependence of the volume pinning force. A model is presented, which describes the pinning force function of irradiated wires using a two-component ansatz involving a point-pinning contribution stemming from radiation induced pinning centers. The dependence of this point-pinning contribution on fast neutron fluence appears to be a universal function for all examined wire types.Comment: 8 page

Phase coexistence and critical temperatures of the (Bi, Pb)2Sr2Ca2Cu3Ox phase under partial pressures of oxygen between 10−3 and 0.21 bar with and without additions of silver

We have investigated the stability of the (Bi, Pb)2Sr2Ca2Cu3Ox phase for the stoichiometry (Bi: Pb: Sr:Ca: Cu = 1.72: 0.34: 1.83: 1.97: 3.13), subjecting it to temperatures between 700 and 850 °C under various oxygen partial pressures. A narrow region was found in which Bi, Pb(2223) was the only superconducting phase. This region follows closely the thermal decomposition line. X-ray pure Bi, Pb(2223) will partially decompose if treated outside of the stability region. For a given oxygen partial pressure, the Bi, Pb(2223) phase tends to coexist with the 2201 phase for temperatures above, and the 2212 phase for temperatures below this region. At even lower temperatures an additional lead-rich phase appears. Critical temperatures Tc vary little with treatment and range between 108.5 K and 110.8 K. If 10% silver is added to the starting powder, the phase coexistence regions shift. Silver does not seem to have a significant effect on the absolute values of the critical temperature. The Bi, Pb(2223) thermal decomposition temperature for a given oxygen pressure is lowered by at least 10 K by the presence of A

The upper critical field of filamentary Nb3Sn conductors

We have examined the upper critical field of a large and representative set of present multi-filamentary Nb3Sn wires and one bulk sample over a temperature range from 1.4 K up to the zero field critical temperature. Since all present wires use a solid-state diffusion reaction to form the A15 layers, inhomogeneities with respect to Sn content are inevitable, in contrast to some previously studied homogeneous samples. Our study emphasizes the effects that these inevitable inhomogeneities have on the field-temperature phase boundary. The property inhomogeneities are extracted from field-dependent resistive transitions which we find broaden with increasing inhomogeneity. The upper 90-99 % of the transitions clearly separates alloyed and binary wires but a pure, Cu-free binary bulk sample also exhibits a zero temperature critical field that is comparable to the ternary wires. The highest mu0Hc2 detected in the ternary wires are remarkably constant: The highest zero temperature upper critical fields and zero field critical temperatures fall within 29.5 +/- 0.3 T and 17.8 +/- 0.3 K respectively, independent of the wire layout. The complete field-temperature phase boundary can be described very well with the relatively simple Maki-DeGennes model using a two parameter fit, independent of composition, strain state, sample layout or applied critical state criterion.Comment: Accepted Journal of Applied Physics Few changes to shorten document, replaced eq. 7-

Upper critical fields well above 100 T for the superconductor SmFeAsO0.85_{0.85}F0.15_{0.15} with Tc_c = 46 K

We report specific heat measurements at magnetic fields up to 20 T on the recently discovered superconductor SmFeAsO$_{0.85}$F$_{0.15}$. The B-T diagram of a polycrystalline SmFeAsO$_{0.85}$F$_{0.15}$ sample with T$_c$ = 46 K was investigated. The temperature dependence of B$_{c2}$ was extracted from the specific heat curves, the corresponding B$_{c2}$(T = 0) value derived from the Werthamer-Helfand-Hohenberg formula being 150 T. Based on magnetization measurements up to 9 T, a first estimation of the field dependence of the inductive critical current J$_c$ is given. Evidence for granularity is found. The presence of a peak effect is reported, suggesting a crossover in the vortex dynamics, in analogy to the behaviour observed in high T$_c$ cuprates.Comment: Accepted for publication in Physical Review

Strong enhancement of Jc in binary and alloyed in-situ MgB2 wires by a new approach: Cold high pressure densification

Cold high pressure densification (CHPD) is presented as a new way to substantially enhance the critical current density of in situ MgB2 wires at 4.2 and 20 K at fields between 5 and 14 T. The results on two binary MgB2 wires and an alloyed wire with 10 wt.% B4C are presented The strongest enhancement was measured at 20K, where cold densification at 1.85 GPa on a binary Fe/MgB2 wire raised both Jcpara and Jcperp by more than 300% at 5T, while Birr was enhanced by 0.7 T. At 4.2K, the enhancement of Jc was smaller, but still reached 53% at 10 T. After applying pressures up to 6.5 GPa, the mass density dm of the unreacted (B+Mg) mixture inside the filaments reached 96% of the theoretical density. After reaction under atmospheric pressure, this corresponds to a highest mass density df in the MgB2 filaments of 73%. After reaction, the electrical resistance of wires submitted to cold densification was found to decrease, reflecting an improved connectivity. A quantitative correlation between filament mass density and the physical properties was established. Monofilamentary rectangular wires with aspect ratios a/b < 1.25 based on low energy ball milled powders exhibited very low anisotropy ratios, Gamma = Jcpara/Jcperp being < 1.4 at 4.2 K and 10T. The present results can be generalized to alloyed MgB2 wires, as demonstrated on a wire with B4C additives. Based on the present data, it follows that cold densification has the potential of further improving the highest Jcpara and Jcperp values reported so far for in situ MgB2 tapes and wires with SiC and C additives. Investigations are under work in our laboratory to determine whether the densification method CHPD can be applied to longer wire or tape lengths.Comment: Submitted to Superconductors Science and Technolog