Performance tests with a 4.75 inch bore tapered-roller bearings at high speeds

The tapered-roller bearings were tested at speeds to 15,000 rpm which results in a cone-rib tangential velocity of 130 m/sec. (25,500 ft/min). Lubrication was applied either by jets or directly to the cone-rib, augmented with jets. Additional test parameters included thrust loads to 53,400 N (12,000 lbs), radial loads to 26,700 N (6,000 lbs), lubricant flow rates from 1.9 x 0.000 to 15.1 x 0.001 cubic meter/min. (0.5 to 4.0 gpm), and lubricant inlet temperatures of 350 K and 364 K (170 F and 195 F). Temperature distribution, separator speed, and drive-motor power demand were determined as functions of these test parameters

Performance of computer-optimized tapered-roller bearings to 2.4 million DN

The performance of 120.65 mm bore high speed design tapered roller bearings was investigated at shaft speeds to 20,000 rpm under combined thrust and radial load. The test bearing design was computer optimized for high speed operation. Temperature distribution and bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rates, and lubricant inlet temperature. The roller bearing operated successfully at shaft speeds up to 20,000 rpm under heavy thrust and radial loads. Cup cooling was effective in decreasing the high cup temperatures to levels equal to the cone temperature

Lubrication of optimized-design tapered-roller bearings to 2.4 million DN

The performance of 120.65 mm (4.75 in.) bore high speed design, tapered roller bearings was investigated at shaft speeds to 20,000 rpm (2.4 million DN) under combined thrust and radial load. The test bearing design was computer optimized for high speed operation. Temperature distribution bearing heat generation were determined as a function of shaft speed, radial and thrust loads, lubricant flow rates, and lubricant inlet temperature. The high speed design, tapered roller bearing operated successfully at shaft speeds up to 20,000 rpm under heavy thrust and radial loads. Bearing temperatures and heat generation with the high speed design bearing were significantly less than those of a modified standard bearing tested previously. Cup cooling was effective in decreasing the high cup temperatures to levels equal to the cone temperature

Endurance tests with large-bore tapered-roller bearings to 2.2 million DN

Endurance life tests were run with standard design and optimized high-speed design 120.65-mm-(4.750-in.-) bore tapered-roller bearings at shaft speeds of 12,500 and 18,500 rpm, respectively. Standard design bearings of vacuum melted AISI 4320 and CBS-1000M, and high-speed design bearings of CBS-1000M and through-hardened AISI M-50 were run under heavy combined radial and thrust load until fatigue failure or until a preset cutoff time of 1100 hours was reached. Standard design bearings made from CBS 1000M material ran to a 10 percent life approximately six times rated catalog life. Twelve identical bearings of AISI 4320 material ran to ten times rated catalog life without failure. Cracking and fracture of the cones of AISI M-50 high-speed design bearings occurred at 18,500 rpm due to high tensile hoop stresses. Four CBS 1000M high-speed design bearings ran to twenty-four times rated catalog life without any spalling, cracking or fracture failures

Effect of cage design on characteristics of high-speed-jet-lubricated 35-millimeter-bore ball bearing

Parametric tests were conducted with a 35 mm bore angular contact ball bearing with a double outer land guided cage. Provisions were made for jet lubrication and outer-ring cooling of the bearing. Test conditions included a combined thrust and radial load at nominal shaft speeds of 48,000 rpm, and an oil-in temperature of 394 K (250 F). Successful operation of the test bearing was accomplished up to 2.5 million DN. Test results were compared with those obtained with similar bearing having a single outer land guided cage. Higher temperatures were generated with the double outer land guided cage bearing, and bearing power loss and cage slip were greater. Cooling the outer ring resulted in a decrease in overall bearing operating temperature

Effect of two inner-ring oil-flow distribution schemes on the operating characteristics of a 35 millimeter bore ball bearing to 2.5 million DN

Parametric tests were conducted with a 35-mm-bore, split-inner-ring ball bearing with a double-inner-land-guided cage. Provisions were made for through-the-inner-ring lubrication. Test condictions were either a thrust load of 667 N (150 lb) or a combined load of 667 N (150 lb) thrust and 222 N (50 lb) radial, shaft speeds from 32000 to 72000 rpm, and an oil-inlet temperature of 394 K (250 deg F). Outer ring cooling was used in some tests. Tests were run with either 50 or 75 percent of the total oil flow distributed to the inner-ring raceway. Successful operation was experienced with both 50% and 75% flow patterns to 2.5 million DN. Cooling the outer ring had little effect on inner-ring temperature; however, the outer-ring temperature decreased as much as 7% at 2.5 million DN. Maximum recorded power loss was 3.1 kW (4.2 hp), and maximum cage slip was 8.7 percent. Both occurred at a shaft speed of 72000 rpm, a lubricant flow rate of 1900 cu/min (0.50 gal/min), a combined load, and no outer-ring cooling

Validity of the Adiabatic Approximation

We analyze the validity of the adiabatic approximation, and in particular the reliability of what has been called the "standard criterion" for validity of this approximation. Recently, this criterion has been found to be insufficient. We will argue that the criterion is sufficient only when it agrees with the intuitive notion of slowness of evolution of the Hamiltonian. However, it can be insufficient in cases where the Hamiltonian varies rapidly but only by a small amount. We also emphasize the distinction between the adiabatic {\em theorem} and the adiabatic {\em approximation}, two quite different although closely related ideas.Comment: 4 pages, 1 figur

¿Un sistema educativo comprensivo?

Any good educational system tries to keep the maximum number of students in the educational system for as long as possible, where he or she will receive a quality education which will prepare him or her for higher education and the labour market. In other words, they fight for a comprehensive educational system. The LOMCE is going to achieve the complete opposite. We shall analyze this more deeply in the following paragraphs. Keywords: Vocational training, higher vocational training, educational method, scholar evaluation, exam, income test, scholar dropout, basic education, secondary education, postsecondary education, higher education, private school, public school.Ningún sistema educativo intenta mantener el máximo número de estudiantes en el sistema educativo durante el mayor tiempo posible, donde el o ella recibirá una educación de calidad la cual los preparará para la educación superior y el mercado laboral. En otras palabras, ellos luchan por un sistema educativo comprensivo. La LOMCE va a lograr todo lo contrario. Nosotros analizaremos esto más profundamente en los siguientes párrafos.ReiDoCrea. Departamento de Psicología Social. Universidad de Granada