Tight bound on coherent states quantum key distribution with heterodyne detection

We propose a new upper bound for the eavesdropper's information in the direct and reverse reconciliated coherent states quantum key distribution protocols with heterodyne detection. This bound is derived by maximizing the leaked information over the symplectic group of transformations that spans every physical Gaussian attack on individual pulses. We exhibit four different attacks that reach this bound, which shows that this bound is tight. Finally, we compare the secret key rate obtained with this new bound to the homodyne rate.Comment: 8 pages, 3 figure

Introduction to special section: Active Fault-Related Folding: Structural Evolution, Geomorphologic Expression, Paleoseismology, and Seismic Hazards

N/

A Unifying Framework for Finite Wordlength Realizations.

A general framework for the analysis of the finite wordlength (FWL) effects of linear time-invariant digital filter implementations is proposed. By means of a special implicit system description, all realization forms can be described. An algebraic characterization of the equivalent classes is provided, which enables a search for realizations that minimize the FWL effects to be made. Two suitable FWL coefficient sensitivity measures are proposed for use within the framework, these being a transfer function sensitivity measure and a pole sensitivity measure. An illustrative example is presented

Split-screen single-camera stereoscopic PIV application to a turbulent confined swirling layer with free surface

An annular liquid wall jet, or vortex tube, generated by helical injection inside a tube is studied experimentally as a possible means of fusion reactor shielding. The hollow confined vortex/swirling layer exhibits simultaneously all the complexities of swirling turbulence, free surface, droplet formation, bubble entrapment; all posing challenging diagnostic issues. The construction of flow apparatus and the choice of working liquid and seeding particles facilitate unimpeded optical access to the flow field. A split-screen, single-camera stereoscopic particle image velocimetry (SPIV) scheme is employed for flow field characterization. Image calibration and free surface identification issues are discussed. The interference in measurements of laser beam reflection at the interface are identified and discussed. Selected velocity measurements and turbulence statistics are presented at Re_λ = 70 (Re = 3500 based on mean layer thickness)

Controllability for chains of dynamical scatterers

In this paper, we consider a class of mechanical models which consists of a linear chain of identical chaotic cells, each of which has two small lateral holes and contains a rotating disk at its center. Particles are injected at characteristic temperatures and rates from stochastic heat baths located at both ends of the chain. Once in the system, the particles move freely within the cells and will experience elastic collisions with the outer boundary of the cells as well as with the disks. They do not interact with each other but can transfer energy from one to another through collisions with the disks. The state of the system is defined by the positions and velocities of the particles and by the angular positions and angular velocities of the disks. We show that each model in this class is controllable with respect to the baths, i.e. we prove that the action of the baths can drive the system from any state to any other state in a finite time. As a consequence, one obtains the existence of at most one regular invariant measure characterizing its states (out of equilibrium)

Single and multiphase CFD approaches for modelling partially baffled stirred vessels: comparison of experimental data with numerical predictions

Whilst the use of CFD to study mixing vessels is now common-place, there are still many specialised applications that are yet to be addressed. Here we present CFD and PIV results for a hydrodynamic study of a partially baffled vessel with a free surface. The standard k.ε and SSG Reynolds Stress turbulence models are used and the numerical predictions of the mean flow field are compared with experimental data for single phase modelling. At low rotation rates a flat free surface is observed and the flow is simulated using a single phase model, whilst at high rotation rates an Eulerian–Eulerian multiphase model is used to capture the free surface location, even under conditions when gas is drawn down to the impeller. It is shown that there are significant transient effects that mean many of the “rules of thumb” that have been developed for fully baffled vessels must be revisited. In particular such flows have central vortices that are unsteady and complex, transient flow-induced vortical structures generated by the impeller–baffle interactions and require a significant number of simulated agitator rotations before meaningful statistical analysis can be performed. Surprisingly, better agreement between CFD and experimental data was obtained using the k.ε than the SSG Reynolds stress model. The multiphase inhomogeneous approach used here with simplified physics assumptions gives good agreement for power consumption, and with PIV measurements with flat and deformed free surfaces, making this affordable method practical to avoid the erroneous modelling assumption of a flat free surface often made in such cases

Morphological operators for very low bit rate video coding

This paper deals with the use of some morphological tools for video coding at very low bit rates. Rather than describing a complete coding algorithm, the purpose of this paper is to focus on morphological connected operators and segmentation tools that have proved to be attractive for compression.Peer ReviewedPostprint (published version

An experimental and computational study of the vortex shape in a partially baffled agitated vessel

The vortex shape in a non-standard partially baffled agitated vessel in the form of a glass-lined, under-baffled stirred vessel has been investigated using both experimental and numerical approaches for an air/water system for different rotation speeds of the agitator. A simple and flexible experimental strategy was developed for determination of the time-averaged location of the unstable free surface using a process involving superimposition of images. CFD simulations were made to predict the vortex shape by using an Eulerian–Eulerian multiphase model coupled with a homogenous turbulence model. The simplifying assumptions of a constant bubble size, a constant drag coefficient and use of the k–ε turbulence model were made. An assessment of the capability of the numerical method to predict the vortex shape was carried out through comparison between experimental data and numerical results. Considering for comparison purposes a water isosurface volume fraction equal to 0.9, to account for the existence of air/water mixture present at the interface in the experiments, instead of the classical value of 0.5, gave very good agreement with the experimental data

An experimental and CFD study of liquid jet injection into a partially baffled mixing vessel: a contribution to process safety by improving the quenching of runaway reactions

Thermal runaway remains a problem in the process industries with poor or inadequate mixing contributing significantly to these incidents. An efficient way to quench such an uncontrolled chemical reaction is via the injection of a liquid jet containing a small quantity of a very active inhibiting agent (often called a stopper) that must be mixed into the bulk of the fluid to quench the reaction. The hazards associated with such runaway events mean that a validated computational fluid dynamics (CFD) model would be an extremely useful tool. In this paper, the injection of a jet at the flat free surface of a partially baffled agitated vessel has been studied both experimentally and numerically. The dependence of the jet trajectory on the injection parameters has been simulated using a single-phase flow CFD model together with Lagrangian particle tracking. The comparison of the numerical predictions with experimental data for the jet trajectories shows very good agreement. The analysis of the transport of a passive scalar carried by the fluid jet and thus into the bulk, together with the use of a new global mixing criterion adapted for safety issues, revealed the optimum injection conditions to maximise the mixing benefits of the bulk flow pattern