Experimental Analysis of Partial Evaporation Micro-ORC for low -temperature Heat Recovery

In this paper, we present an experimental assessment of the performance of a partial evaporating organic Rankine cycle (PE-ORC) power system. The system converts low temperature heat into electrical energy, with a power size around 1 kW, thus suitable for micro generation in the residential sector. Although the test bench was designed for operating with superheated vapour at the expander inlet, it has demonstrated to be able to work with the expansion occurring entirely in two-phase condition. Since the direct measurement of the vapour quality is not possible using the sensors installed in the test rig, the state of the fluid in the two-phase condition is estimated by means of the thermal balance at the heat exchangers, so the thermodynamic cycle can be evaluated. Temperatures of the heat source in the range between 40 C and 75 C have been tested, and for each temperature value the vapour quality at the expander inlet has been varied by regulating the feed -pump rotating speed. Experimental data are provided regarding the performance of the overall cycle, of the heat exchangers, of the expander and of the feed -pump. It was observed that the effectiveness of the evaporator and the efficiency of the pump are improved with respect to the operation with superheated vapour at the expander inlet. However, the overall performance is lower, especially due to the high ratio of the pump consumption over the expander produced power, commonly called back work ratio (BWR). The latter, under some boundary conditions, has resulted higher than the unit, meaning that the system is not able to produce net electrical power. The aim of the paper is to identify the design characteristics required by a micro -ORC energy system in order to enhance its performance in the PE operating mode

Storage Solutions for Renewable Production in Household Sector

Abstract The penetration of renewable sources, particularly wind and solar, into the grid has been increasing in recent years. As a consequence, there have been serious concerns over reliable and safety operation of power systems. One possible solution, to improve grid stability, is to integrate energy storage devices into power system network: storing energy produced in periods of low demand to later use, ensuring full exploitation of intermittent available sources. Focusing on stand-alone photovoltaic (PV) energy system, energy storage is needed with the purpose of ensuring continuous power flow, to minimize or, if anything, to neglect electrical grid supply. A comprehensive study on a hybrid stand-alone photovoltaic power system using two different energy storage technologies has been performed. This study examines the feasibility of replacing electricity provided by the grid with hybrid system to meet household demand. This paper is a part of an experimental and a theoretical study which is currently under development at University of Bologna. A test facility is under construction, at the University of Bologna, for the experimental characterization of the cogenerative performance of small scale hybrid power systems, composed of micro-CHP systems of different technologies : a Micro Rankine Cycles (MRC), a Proton Exchange Membrane Fuel Cells (PEM-FC), a battery, an electrolyzer and a heat recovery subsystem. The test set-up is also integrated with an external load simulator, in order to generate variable load profiles. This paper presents the theoretical results of the performance simulations developed considering an hybrid system consisting on a photovoltaic array (PV), electrochemical batteries (B) and electrolyzer (HY) with a H2 tank and a Proton Exchange Membrane Fuel Cell (PEM-FC) stack, in case of a household electrical demand. The performance of this system have been evaluated by the use of a calculation code, in-house developed by University of Bologna; future activities will be the tuning of the software with the experimental results, in order to realize a code able to define the correct size of each sub-system, ones the load profile of the utility is known or estimated

Advanced Waste-to-energy Steam Cycles

AbstractThis paper focuses on possibilities to maximize waste conversion through integration of a Waste-To-Energy (WTE) plant with a gas turbine (GT). In particular, this study investigates the feasibility of utilizing the hot gases leaving the GT mainly to superheat the steam leaving the WTE steam generator. A parametric investigation on the steam production is carried out and the optimum plant match condition in terms of plants capacity ratio is identified and discussed. Detailed modifications to a typical WTE cycle arrangement are presented, in order to evaluate the resulting performance enhancement. Numerical results of a conventional reference WTE plant repowering with different GT commercial units are shown and discussed. Performance indexes, specifically introduced in order to assess the proposed integrated configuration and to allocate power output to each input fuel are illustrated and applied on the considered plant. Results of the study suggest possibilities to create new advanced WTE-GT integrated power plants or to repower existing WTE plants, in order to increase waste to energy conversion

Performance Increase of a Small-scale Liquefied Natural Gas Production Process by Means of Turbo-expander☆

Abstract In the last years, the growing demand of the energy market has led to the increasing penetration of renewable energy sources in order to achieve the primary energy supply. However, in the next years fossil fuels are expected to remain the dominant energy source, due to the forecasted increase of global energy consumption. In particular, the natural gas is predicted to still play a key role in the energy market, on account of its lower environmental impact than other fossil fuels. Natural gas is currently employed mainly as gaseous fuel for stationary energy generation, but also as liquefied fuel, as an alternative to the diesel fuel, in vehicular applications. Liquefied Natural Gas (LNG) is currently produced in large plants directly located at the extraction sites. The aim of the study is the definition of an optimal small-scale production process for LNG, to be realized – in opposition to the current habit – directly at filling stations. With this purpose, two different LNG production layouts have been proposed and investigated within a thermodynamic analysis: starting from a Joule-Thompson LNG expansion process, a new layout with a turbo-expander has been proposed for the natural gas liquefaction. The carried-out simulations show that the new proposed solution allow to optimize the LNG production process and to minimize the process' energy consumption

Thermodynamic Evaluation of Repowering Options for a Small-size Combined Cycle with Concentrating Solar Power Technology☆

Abstract The increasing penetration of low-carbon technologies and enhancements in fossil-fuelled power plants efficiency are some of the most important and up to date research topics. Renewable energy, in particular solar, has the potential of meeting the world energy needs while addressing environmental concerns, but technological advances in renewable energy electricity production are necessary to become competitive with conventional technologies. New opportunities to increase the penetration of renewables energies, smoothing out renewables variability and intermittency problems, come out from the hybridization concept. Hybrid renewable-fossil fuel systems join the advantages of both renewable energies and programmable devices. Among all the renewable technologies available for hybridization, Concentrating Solar Power (CSP) with parabolic trough is the most diffused because of its relatively conventional technology and ease of scale-up. CSP hybrids are well established worldwide, predominantly with natural gas: the hybridization options for CSP ranging from feed water heating, reheat steam, live steam to steam superheating. Based on a detailed thermodynamic cycle model of a reference small-size one pressure level Combined Cycle (CC) plant, the impact of CSP addition is thoroughly evaluated. Different hybrid schemes are evaluated and compared considering CC off-design operation. The goal of this study is to evaluate, from a thermodynamic point of view, three repowering options of a small-size CC with a CSP system in a hybrid system configuration and to quantify their potential benefits in terms of system's performance increase. In particular, the optimal size of CSP plant is shown for each investigated hybrid repowering options. The changes in CC steam cycle operating parameters are presented together with CC performance increase. It is shown that solar hybridization into an existing CC plant may give rise to a substantial benefit from a thermodynamic point of view

Pump Hydro Storage and Gas Turbines Technologies Combined to Handle Wind Variability: Optimal Hydro Solution for an Italian Case Study☆

Abstract Load and wind energy profiles are totally uncorrelated, therein lies the problem of variable energy sources. Managing load with increasing wind penetration may call for operational ranges that conventional systems cannot readily access. Storage technologies could allow tolerating the unsteadiness of renewable sources with smaller fossil fuel plants capacity. Pumped Hydro Storage (PHS) is a crucial technology for balancing large steam power plants and may become increasingly important for storing renewable energies. Hence capacity ranges of PHS as well as its dynamic response to renewable power variability, will become progressively relevant. An integrated system made of a wind farm, a PHS plant and a set of gas turbines (GTs), as programmable fossil fuel devices, to handle renewable variability and maximize renewable energy exploitation, is studied in this paper. A specific case study is analyzed: a wind farm with a nameplate capacity equal to that installed in Sardinia is considered. To match the power output requested by the region with the integrated systems different configurations of PHS plant will be investigated. The impact of reversible or separate Francis machines with constant or variable speed will be analyzed in order to minimize electric power output overproduction and GTs fuel consumptions. Minimum and maximum capacity range for reversible or separate machines will be considered. The aim of the study is the optimum sizing and design of a PHS unit in a hybrid wind-hydro-gas turbine power plant to match the load request. Results in terms of PHS operation, water height behavior in upper and lower reservoirs, GT units power output, natural gas consumed and electric power output overproduction will be presented for each analyzed case

Low-temperature district heating networks for complete energy needs fulfillment

In order to reduce fossil fuels consumption and pollutant emissions, high contribution is given by district heating. In particular, the integration with renewable energy may lead to a significant increase in energy conversion efficiency and energy saving. Further benefits can be achieved with low temperature networks, reducing the heat dissipations and promoting the exploitation of low enthalpy heat sources. The aim of the paper is the analysis of the potential related to the conversion of existing district heating networks, to increase the exploitation of renewables and eliminate pollutant emissions in the city area. Further aim, in this context, is the optimization \u2013 from both energy production and operation management viewpoints \u2013 of a low temperature district heating network for the fulfillment of the connected users\u2019 energy needs. To this respect, a traditional network with a fossil fuel driven thermal production plant has been considered and compared with a low temperature district heating scenario, including geothermal heat pumps, photovoltaic panels and absorption chillers. These scenarios have been analyzed and optimized with a developed software, demonstrating the reduction of primary energy consumption and CO2 pollutant emissions achievable with low temperature networks. In addition, a preliminary economic comparative evaluation on the variable costs has been carried out. Future studies will investigate the economic aspect also from the investment costs viewpoint

Simplified Model for PV Panels Performance Preditcion

Abstract In the last years, the growing global energy demand and the even more strictly pollution regulations have led the research to improve efficiency of conventional technologies and to find out innovative solutions to solve these issues. In this scenario, the renewable energy becomes a fundamental resource, especially in the field of electric energy generation. Problems related to non-programmability and effectiveness of renewables can be minimize through the diffusion of distributed generation and energy storage technologies. In this study, an integrated microgrid, made up of photovoltaic arrays, batteries and a hydrogen generator is presented. The aim of this work is to develop a simplified mathematical model able to describe the behavior of the photovoltaic modules for different operating conditions. On the respect of available literature on this topic, the peculiarity of this model is the possibility of being used simply knowing those parameters usually provided by manufacturers. To validate the model, experimental data recorded during the laboratory tests have been used. Obtained results show that 78 % of the analyzed operating conditions computed using the developed model are within the tolerance range of ± 10 % compared to experimental values

Low temperature district heating networks for complete energy needs fulfillment

In order to reduce fossil fuels consumption and pollutant emissions, high contribution is given by district heating. In particular, the integration with renewable energy may lead to a significant increase in energy conversion efficiency and energy saving. Further benefits can be achieved with low temperature district heating, reducing the thermal dissipations through the network and promoting the exploitation of low enthalpy heat sources. The aim of the paper is the analysis of the potential related to the conversion of existing district heating networks, to increase the exploitation of renewable sources and eliminate pollutant emissions in the city areas. Further aim, in this context, is the optimization – from both energy production and operation management viewpoints – of a low temperature district heating network for the fulfillment of the connected users’ energy needs. To this respect, a traditional network with a fossil fuel driven thermal production plant has been considered and compared with a low temperature district heating scenario, including geothermal heat pumps, photovoltaic panels and absorption chillers. These scenarios have been analyzed and optimized with an in-house developed software, allowing to demonstrate the reduction of primary energy consumption and CO2 pollutant emissions achievable with low temperature networks. In addition, a preliminary economic evaluation has been carried out to compare the proposed solution with traditional district heating

Complex energy networks: Energy-ecological efficiency based evaluations towards the sustainability in energy sector

In the last years, international programs in diverse sectors and national frameworks have been driven by the need of a sustainable growth, in a green economy perspective. In order to reduce the energy losses/dissipations, as well as the fossil fuels employment and related pollutant emissions, indeed, the spread of combined heat and power units and/or renewable sources generators is promoted into both the electrical grids and the thermal networks but are often in conflict with the economic aspects. In this context, the optimal management of complex energy networks - including, in particular, smart district heating - may lead to the achievement of important goals from the environmental and sustainability viewpoints. The aim of this paper is to develop a preliminary methodology for the complete evaluation of complex energy networks, considering energy, economic and environmental aspects. With this purpose, a case study consisting in a network for the fulfillment of electrical and thermal needs of the connected users will be analyzed, considering different scenarios in terms of energy generation mix and operation and applying different optimization software. In addition, the carried out evaluations will allow to set the basis for the discussion about the future of energy policies and possible incentives towards the sustainable development of the energy sector