Lubrication in cold rolling: Elasto-plasto-hydrodynamic lubrication

A model has been developed with respect to hydrodynamic lubrication in cold rolling. The basic model describes the configuration of a rigid, perfectly plastic sheet rolled by a rigid work roll. The governing equations have been solved throughout the complete contact area, i.e. the inlet, the work zone and the outlet zone. Multi-level techniques have been applied to solve these equations together with boundary conditions, resulting in an algorithm solving the problem in O(n) operations. This means that the distribution of the pressure and the traction force in the lubricant film, and the shape of this film, as well as the plastic deformation of the sheet, can be accurately calculated for a large number of nodal points on a minicomputer. Subsequently elastic deformation, work hardening and dynamic behaviour of the flow stress have been incorporated in the model. It will be shown that the influence of these effects on the film thickness or the pressure distribution is considerable

Effect of Thickener Particle Geometry and Concentration on the Grease EHL Film Thickness at Medium Speeds

The aim of this paper was to understand the parameters influencing the grease film thickness in a rolling elastohydrodynamically lubricated contact under fully flooded conditions at medium speeds. Film thickness measurements were taken under pure rolling for six commercial greases and their bled oils. The grease film thickness was found to be higher than corresponding bled oil, suggesting the presence of thickener in the contact. No rheological properties (characterized by steady and dynamic shear) showed any direct relation to the film thickness of the studied greases. AFM measurements of the thickener microstructure, from which the dimensional properties of the thickener particles (fibers/platelets/spheres) were estimated, showed that the relative increase in the film thickness due to entrainment of the thickener was proportional to the ratio of thickener volume fraction to the size of the fibers/platelets/spheres. Hence, with the same concentration, smaller thickener particles lead to the generation of thicker films than larger thickener particles. Next, this relation was used to establish the percentage of the thickener particles passing through the contact. Depending on the grease type, between about 1 and 70 % of the thickener particles were found to travel through the contact

Characterization of Friction and Wear Behavior of Friction Modifiers used in Wheel-Rail Contacts

Reliable traction between wheel and rail is an important issue in the railway industry. To reduce variations in the coefficient of friction, so-called “friction modifiers” (carrier with particles) are used. Twin-disk tests were done with three commercial friction modifiers, based on different compositions of carrier and particles, to characterize their friction and wear behavior. It is shown experimentally that the influence of the carrier cannot be neglected just after application and very low (0.01-0.05) frictional values are observed in a fully flooded situation. However, starvation occurs quickly and friction values will become relatively stable at an intermediate level around μ=0.2 until the friction modifier is consumed and a new dose is required. After the carrier is pushed out of the running track the particles in the contact dominate the tribological performance. The level of friction is a function of total rolling distance, effective sliding length and sum velocity. The most dominant factor depends on the friction modifier and the working mechanism for friction stabilization. It is also shown that the wear rates during tests do not depend significantly on slip, which makes it possible to predict wear behavior. Wear rates are dependent on the type of friction modifier used

Tensile and Compressive Mechanical Behaviour of Human Blood Clot Analogues

Endovascular thrombectomy procedures are significantly influenced by the mechanical response of thrombi to the multi-axial loading imposed during retrieval. Compression tests are commonly used to determine compressive ex vivo thrombus and clot analogue stiffness. However, there is a shortage of data in tension. This study compares the tensile and compressive response of clot analogues made from the blood of healthy human donors in a range of compositions. Citrated whole blood was collected from six healthy human donors. Contracted and non-contracted fibrin clots, whole blood clots and clots reconstructed with a range of red blood cell (RBC) volumetric concentrations (5–80%) were prepared under static conditions. Both uniaxial tension and unconfined compression tests were performed using custom-built setups. Approximately linear nominal stress–strain profiles were found under tension, while strong strain-stiffening profiles were observed under compression. Low- and high-strain stiffness values were acquired by applying a linear fit to the initial and final 10% of the nominal stress–strain curves. Tensile stiffness values were approximately 15 times higher than low-strain compressive stiffness and 40 times lower than high-strain compressive stiffness values. Tensile stiffness decreased with an increasing RBC volume in the blood mixture. In contrast, high-strain compressive stiffness values increased from 0 to 10%, followed by a decrease from 20 to 80% RBC volumes. Furthermore, inter-donor differences were observed with up to 50% variation in the stiffness of whole blood clot analogues prepared in the same manner between healthy human donors

The association between human blood clot analogue computed tomography imaging, composition, contraction, and mechanical characteristics

Background Clot composition, contraction, and mechanical properties are likely determinants of endovascular thrombectomy success. A pre-interventional estimation of these properties is hypothesized to aid in selecting the most suitable treatment for different types of thrombi. Here we determined the association between the aforementioned properties and computed tomography (CT) characteristics using human blood clot analogues. MethodsClot analogues were prepared from the blood of 4 healthy human donors with 5 red blood cell (RBC) volume suspensions: 0%, 20%, 40%, 60% and 80% RBCs. Contraction was measured as the weight of the contracted clots as a percentage of the original suspension. The clots were imaged using CT with and without contrast to quantify clot density and density increase. Unconfined compression was performed to determine the high strain compressive stiffness. The RBC content was analysed using H&amp;E staining. Results The 5 RBC suspensions formed only two groups of clots, fibrin-rich (0% RBCs) and RBC-rich (&gt;90% RBCs), as determined by histology. The density of the fibrin-rich clots was significantly lower (31-38HU) compared to the RBC-rich clots (72-89HU), and the density increase of the fibrin-rich clots was significantly higher (82-127HU) compared to the RBC-rich clots (3-17HU). The compressive stiffness of the fibrin-rich clots was higher (178–1624 kPa) than the stiffness of the RBC-rich clots (6–526 kPa). Additionally, the degree of clot contraction was higher for the fibrin-rich clots (89–96%) compared to the RBC-rich clots (11–77%). ConclusionsCT imaging clearly reflects clot RBC content and seems to be related to the clot contraction and stiffness. CT imaging might be a useful tool in predicting the thrombus characteristics. However, future studies should confirm these findings by analysing clots with intermediate RBC and platelet content.</p

The association between human blood clot analogue computed tomography imaging, composition, contraction, and mechanical characteristics

Background Clot composition, contraction, and mechanical properties are likely determinants of endovascular thrombectomy success. A pre-interventional estimation of these properties is hypothesized to aid in selecting the most suitable treatment for different types of thrombi. Here we determined the association between the aforementioned properties and computed tomography (CT) characteristics using human blood clot analogues. MethodsClot analogues were prepared from the blood of 4 healthy human donors with 5 red blood cell (RBC) volume suspensions: 0%, 20%, 40%, 60% and 80% RBCs. Contraction was measured as the weight of the contracted clots as a percentage of the original suspension. The clots were imaged using CT with and without contrast to quantify clot density and density increase. Unconfined compression was performed to determine the high strain compressive stiffness. The RBC content was analysed using H&amp;E staining. Results The 5 RBC suspensions formed only two groups of clots, fibrin-rich (0% RBCs) and RBC-rich (&gt;90% RBCs), as determined by histology. The density of the fibrin-rich clots was significantly lower (31-38HU) compared to the RBC-rich clots (72-89HU), and the density increase of the fibrin-rich clots was significantly higher (82-127HU) compared to the RBC-rich clots (3-17HU). The compressive stiffness of the fibrin-rich clots was higher (178–1624 kPa) than the stiffness of the RBC-rich clots (6–526 kPa). Additionally, the degree of clot contraction was higher for the fibrin-rich clots (89–96%) compared to the RBC-rich clots (11–77%). ConclusionsCT imaging clearly reflects clot RBC content and seems to be related to the clot contraction and stiffness. CT imaging might be a useful tool in predicting the thrombus characteristics. However, future studies should confirm these findings by analysing clots with intermediate RBC and platelet content.</p

Are Insider Sales Always Bad News? Evidence On Large Sales By Key Insiders

Investors often scrutinize stock trades by corporate insiders, hoping to infer the nature of any privileged information which may have motivated the trades. Conventional wisdom suggests that sales of stock by insiders reveal negative information; this interpretation is supported by empirical work such as the series of papers by Seyhun. However, this common interpretation fails to distinguish between sales by atomistic insiders and sales by controlling blockholders.&nbsp; In this paper, I present evidence which suggests that sales by controlling insiders should not be considered bad news. Using both a series of logit regressions and traditional event-study tests, I examine the relationship between a firm's performance and the willingness of its controlling shareholder to sell a significant proportion of his shares. I find that firm value is just as likely to rise on the news of large insider sales as it is to fall, so that large sales need not imply negative private information.&nbsp; One possible explanation for a positive response to a controlling blockholder's large sale is that such a sale makes the insider vulnerable to meaningful oversight by outside shareholders. Thus, a large sale may be a signal of the insider's willingness to expose himself to shareholder monitoring and discipline. However, regardless of the interpretation, the empirical evidence presented in the paper forces the conclusion that it is inappropriate to interpret all insider sales as bad news: insider sales occur in a variety of contexts, and creating buy/sell rules which ignore those contexts is simplistic and erroneous