Rho-Omega Mixing and the Pion Form Factor in the Time-like Region

We determine the magnitude, phase, and $s$-dependence of $\rho$-$\omega$ ``mixing'' in the pion form factor in the time-like region through fits to e^+e^- \ra \pi^+ \pi^- data. The associated systematic errors in these quantities, arising from the functional form used to fit the $\rho$ resonance, are small. The systematic errors in the $\rho$ mass and width, however, are larger than previously estimated.Comment: 20 pages, REVTeX, epsfig, 2 ps figures, minor change

New data on OZI rule violation in bar{p}p annihilation at rest

The results of a measurement of the ratio R = Y(phi pi+ pi-) / Y(omega pi+ pi-) for antiproton annihilation at rest in a gaseous and in a liquid hydrogen target are presented. It was found that the value of this ratio increases with the decreasing of the dipion mass, which demonstrates the difference in the phi and omega production mechanisms. An indication on the momentum transfer dependence of the apparent OZI rule violation for phi production from the 3S1 initial state was found.Comment: 11 pages, 3 PostScript figures, submitted to Physics Letter

Study of the process e+e−→π+π−π0e^+e^- \to \pi^+\pi^-\pi^0 in the energy region s\sqrt[]{s} below 0.98 GeV

The cross section of the process $e^+e^-\to \pi^+\pi^-\pi^0$ was measured in the Spherical Neutral Detector (SND) experiment at the VEPP-2M collider in the energy region $\sqrt[]{s}$ below 980 MeV. This measurement was based on about $1.2 \times 10^6$ selected events. The obtained cross section was analyzed together with the SND and DM2 data in the energy region $\sqrt[]{s}$ up to 2 GeV. The $\omega$-meson parameters: $m_\omega=782.79\pm 0.08\pm 0.09$ MeV, $\Gamma_\omega=8.68\pm 0.04\pm 0.15$ MeV and $\sigma(\omega\to 3\pi)=1615\pm 9\pm 57$ nb were obtained. It was found that the experimental data cannot be described by a sum of only $\omega$, $\phi$, $\omega^\prime$ and $\omega^{\prime\prime}$ resonances contributions. This can be interpreted as a manifestation of $\rho\to 3\pi$ decay, suppressed by $G$-parity, with relative probability $B(\rho\to 3\pi) = (1.01\pm^{0.54}_{0.36}\pm 0.034) \times 10^{-4}$.Comment: 41 pages REVTEX and 34 figure

Proton-Antiproton Annihilation and Meson Spectroscopy with the Crystal Barrel

This report reviews the achievements of the Crystal Barrel experiment at the Low Energy Antiproton Ring (LEAR) at CERN. During seven years of operation Crystal Barrel has collected very large statistical samples in pbarp annihilation, especially at rest and with emphasis on final states with high neutral multiplicity. The measured rates for annihilation into various two-body channels and for electromagnetic processes have been used to test simple models for the annihilation mechanism based on the quark internal structure of hadrons. From three-body annihilations three scalar mesons, a0(1450), f0(1370) and f0(1500) have been established in various decay modes. One of them, f0(1500), may be identified with the expected ground state scalar glueball.Comment: 64 pages, LATEX file, 36 figures are available as ps files at http://afuz01.cern.ch/claude/ Submitted to Reviews of Modern Physic

Light Meson Spectroscopy

We survey the current status of light meson spectroscopy. We begin with a general introduction to meson spectroscopy and and its importance in understanding the physical states of Quantum Chromo Dynamics (QCD). Phemenological models of hadron spectroscopy are described with particular emphasis on the constituent quark model and the qualitative features it predicts for the meson spectrum. We next discuss expectations for hadrons lying outside the quark model, such as hadron states with excited gluonic degrees of freedom. These states include so-called hybrids glueballs}, as well as multiquark states. The established meson states are compared to the quark model predictions and we find that most meson states are well described by the quark model. However, a number of states in the light-quark sector do not fit in well, suggesting the existence of hadronic states with additional degrees of freedom. We end with a brief description of future directions in meson spectroscopy.Comment: 111 pages with 28 imbedded figures, in LaTeX2e with no special macros. Submitted to Reviews of Modern Physics, Nov.12, 199

Ceramic substrates with aluminum metallization for power application

The reliability of power electronic devices is significantly related to the material properties of the applied substrates which carry the semiconductor chip and the electric interconnections. The most common solution to fulfill the stringent requirements of these devices, with respect to high isolation voltage, good thermal conductivity, high temperature cycling reliability and low cost, is to use ceramic substrates with copper layers on both sides. However, the currently increasing reliability standards in power electronics lead to a situation where common DCB substrates reach their limits in meeting these higher requirements. In previous years, ceramic substrates with aluminum instead of the copper metallization layers (Direct Aluminum Bonding, DAB) were introduced. For DAB substrates, a higher reliability especially for temperature cycling tests was found. In this study, results of Finite Element simulations of DAB substrates are presented. For the DAB samples, signi ficantly lower mechanical stresses inside the ceramic were found in comparison to DCB substrates with the same thermal loading situation, thus explaining the improvements in reliability. In addition, the DAB bonding contacts between the aluminum metallization and the alumina were assessed by Scanning Acoustic Microscopy (SAM) and microstructure analysis on cross sections by Scanning Electron Microscopy (SEM) and Energy Dispersive x-ray spectroscopy (EDS). The results indicate good adhesion between the metal layer and the ceramic due to the found interface microstructure and the lack of defects. Thus, Direct Bonded Aluminium (DAB) substrates provide a promising alternative solution to realize more reliable substrates for power electronic devices, in particular to consider the increasing requirements from automotive and avionic industry