Stress on Cold Mass Due to the Supporting System of the CMS Coil in the Vacuum Tank

This report contains a verification analysis of the stress on cold mass coming from the supporting system of the CMS coil in the vacuum tank. The need to carry out this analysis is related to the high mechanical requirements for $9 Al-alloy mandrels (218 MPa yield at cryogenic temperature), demanding accurate analysis of the impact of supporting system on cylinder stress

Detailed Field Distribution in CMS Winding

The CMS winding has now arrived at its constructive phase. This means that some practical aspects regarding the winding itself have to be considered, such as the minimum requirement of conductor performance for each layer of each $9 module. Several magnetic calculations have been already performed, but the winding has been never analyzed in detail, in order to understand the impact of the self-field on its performances. This analysis and its implications are$9 reported in this paper

Low-field Instabilities in Nb3_{3}Sn Multifilamentary Wires: the Possible Role of Unreacted Nb

We report an experimental study aiming to demonstrate the not negligible role of unreacted Nb on the magnetic instabilities in superconducting Nb$_{3}$Sn multifilamentary wires, observable through partial flux jumps at magnetic field values below 0.5 T. The analysed wires were recently developed for use as dipoles required in future high-energy proton accelerators and are based on powder-in-tube technology. We studied both unreacted (only involving Nb filaments) and reacted wires, finding flux jump instabilities in both cases when performing magnetic measurements. The results can be interpreted on the basis of the critical state model and are coherent with the intrinsic stability criterion

Study of coupling loss on bi-columnar BSCCO/Ag tapes by a.c. susceptibility measurements

Coupling losses were studied in composite tapes containing superconducting material in the form of two separate stacks of densely packed filaments embedded in a metallic matrix of Ag or Ag alloy. This kind of sample geometry is quite favorable for studying the coupling currents and in particular the role of superconducting bridges between filaments. By using a.c. susceptibility technique, the electromagnetic losses as function of a.c. magnetic field amplitude and frequency were measured at the temperature T = 77 K for two tapes with different matrix composition. The length of samples was varied by subsequent cutting in order to investigate its influence on the dynamics of magnetic flux penetration. The geometrical factor $\chi_0$ which takes into account the demagnetizing effects was established from a.c. susceptibility data at low amplitudes. Losses vs frequency dependencies have been found to agree nicely with the theoretical model developed for round multifilamentary wires. Applying this model, the effective resistivity of the matrix was determined for each tape, by using only measured quantities. For the tape with pure silver matrix its value was found to be larger than what predicted by the theory for given metal resistivity and filamentary architecture. On the contrary, in the sample with a Ag/Mg alloy matrix, an effective resistivity much lower than expected was determined. We explain these discrepancies by taking into account the properties of the electrical contact of the interface between the superconducting filaments and the normal matrix. In the case of soft matrix of pure Ag, this is of poor quality, while the properties of alloy matrix seem to provoke an extensive creation of intergrowths which can be actually observed in this kind of samples.Comment: 20 pages 11 figure, submitted to Superconductor Science and Technolog

Nb3_3Sn conductor development and characterization for NED

The main purpose of Next European Dipole (NED) project is to design and to build an Nb$_{3}$Sn ~ 15 T dipole magnet. Due to budget constraints, NED is mainly focused on superconducting cable development and production. In this work, an update is given on the NED conductor development by Alstom-MSA and SMI, which uses, respectively, Internal-Tin-Diffusion and Powder-In-Tube methods, with the aim of reaching a non-copper critical current density of ~ 3000 A/mm2 at 12 T and 4.2 K. Characterization results, including critical current and magnetization data, are presented and discussed, as well, for conductors already developed by both companies for this project. SMI succeeded to produce a strand with 50 µm diameter filaments and with a critical current of ~ 1400 A at 4.2 K and 12 T, corresponding to a non-copper critical current density of ~ 2500 A/mm2. Cabling trials with this strand were successfully carried out at LBNL