193 research outputs found
Experimental clean combustor program: Turbulence characteristics of compressor discharge flows
The results of turbulence measurements at the entrance to the diffuser duct of a large gas turbine are presented. Hot film and hot wire measurements were conducted over a compressor discharge temperature range of 450K to 608K. It was found that the turbulent intensity at the I.D. and midspan locations increases gradually from 6 + or - 1 percent at idle to 7 + or - 1 percent at approach; the turbulent intensity at the O.D. location increases from 7.5 + or - 0.5 percent at idle to 15 + or - 0.5 percent at approach. The energy in the velocity waves is uniformly distributed over a 0.1 to 5 kHz bandwidth, and the cut-off frequency is not a strong function of the engine operation. The axial length of the Fourier components within this bandwidth varies from 0.021 to 1.05m. The turbulence near the diffuser O.D. is of sufficient amplitude and scale to affect the flow to the front end sections of the burner
Recommended from our members
Machining and grinding: High rate deformation in practice
Machining and grinding are well-established material-working operations involving highly non-uniform deformation and failure processes. A typical machining operation is characterized by uncertain boundary conditions (e.g.,surface interactions), three-dimensional stress states, large strains, high strain rates, non-uniform temperatures, highly localized deformations, and failure by both nominally ductile and brittle mechanisms. While machining and grinding are thought to be dominated by empiricism, even a cursory inspection leads one to the conclusion that this results more from necessity arising out of the complicated and highly interdisciplinary nature of the processes than from the lack thereof. With these conditions in mind, the purpose of this paper is to outline the current understanding of strain rate effects in metals
Recommended from our members
New experimental techniques with the split Hopkinson pressure bar
The split Hopkinson pressure bar or Kolsky bar has provided for many years a technique for performing compression tests at strain rates approaching 10/sup 4/ s/sup -1/. At these strain rates, the small dimensions possible in a compression test specimen give an advantage over a dynamic tensile test by allowing the stress within the specimen to equilibrate within the shortest possible time. The maximum strain rates possible with this technique are limited by stress wave propagation in the elastic pressure bars as well as in the deforming specimen. This subject is reviewed in this paper, and it is emphasized that a slowly rising excitation is preferred to one that rises steeply. Experimental techniques for pulse shaping and a numerical procedure for correcting the raw data for wave dispersion in the pressure bars are presented. For tests at elevated temperature a bar mover apparatus has been developed which effectively brings the cold pressure bars into contact with the specimen, which is heated with a specially designed furnace, shortly before the pressure wave arrives. This procedure has been used successfully in tests at temperatures as high as 1000/sup 0/C
High strain-rate material model validation for laser peening simulation
Finite element modeling can be a powerful tool for predicting residual stresses induced by laser peening; however the sign and magnitude of the stress predictions depend strongly on how the material model captures the high strain rate response. Although a Johnson-Cook formulation is often employed, its suitability for modeling phenomena at very high strain rates has not been rigorously evaluated. In this paper, we address the effectiveness of the Johnson-Cook model, with parameters developed from lower strain rate material data (∼10^3 s^–1), to capture the higher strain rate response (∼10^5–10^6 s^–1) encountered during the laser peening process. Published Johnson-Cook parameters extracted from split Hopkinson bar testing were used to predict the shock response of aluminum samples during high-impact flyer plate tests. Additional quasi-static and split Hopkinson bar tests were also conducted to study the model response in the lower strain rate regime. The overall objective of the research was to ascertain whether a material model based on conventional test data (quasi-static compression testing and split Hopkinson bar measurements) can credibly be used in FE simulations to predict laser peen-induced stresses
Ti6Al4V metal cutting chip formation experiments and modelling over a wide range of cutting speeds
Measured forces, chip geometry and tool temperatures from machining a mill annealed Ti6Al4V at cutting speeds mainly from 1 to 100 m/min, but in some cases down to 0.1 m/min, are reported, as well as mechanical testing of the material. Finite element simulations with inputs the measured flow stress, and subsequently a small high temperature strain hardening recovery correction, and a failure model calibrated from the cutting tests at speeds from 1 to 10 m/min, give satisfactory agreement with the higher speed tests once surface strain hardening and damage from the previous pass of the tool are taken into account. This paper’s originality is firstly to show that more complicated flow stress models involving large strain softening are not needed provided shear failure is included; and secondly its failure model: this proposes a non-zero failed shear stress depending on local pressure and temperature. The simulations provide relations between tool mechanical and thermal loading and cutting conditions to aid process improvement
Autoimmune inflammatory disorders, systemic corticosteroids and pneumocystis pneumonia: A strategy for prevention
BACKGROUND: Pneumocystis pneumonia (PCP) is an increasing problem amongst patients on immunosuppression with autoimmune inflammatory disorders (AID). The disease presents acutely and its diagnosis requires bronchoalveolar lavage in most cases. Despite treatment with intravenous antibiotics, PCP carries a worse prognosis in AID patients than HIV positive patients. The overall incidence of PCP in patients with AID remains low, although patients with Wegener's granulomatosis are at particular risk. DISCUSSION: In adults with AID, the risk of PCP is related to treatment with systemic steroid, ill-defined individual variation in steroid sensitivity and CD4+ lymphocyte count. Rather than opting for PCP prophylaxis on the basis of disease or treatment with cyclophosphamide, we argue the case for carrying out CD4+ lymphocyte counts on selected patients as a means of identifying individuals who are most likely to benefit from PCP prophylaxis. SUMMARY: Corticosteroids, lymphopenia and a low CD4+ count in particular, have been identified as risk factors for the development of PCP in adults with AID. Trimethoprim-sulfamethoxazole (co-trimoxazole) is an effective prophylactic agent, but indications for its use remain ill-defined. Further prospective trials are required to validate our proposed prevention strategy
Dynamic response and residual stress fields of Ti6Al4V alloy under shock wave induced by laser shock peening
- …