An investigation into the effect of rate of stirring of bath electrolyte on the properties of electrodeposited CdTe thin film semiconductors

Electrodeposition (ED) has been recognized as a low cost and scalable technique available for fabrication of CdS/CdTe solar cells. Photovoltaic activity of these electrodeposited semiconductor materials drastically depends on the ED growth parameters namely; electrodeposition potential, concentrations and ratios of concentrations of precursors used to prepare the bath electrolyte, pH of the electrolyte, deposition temperature and rate of stirring of the electrolyte. In order to grow thin films with good photovoltaic properties, it is essential to maintain these variables at their optimum ranges of values during electrodepositions. Hence, this study was conducted to investigate the dependence of the properties of electrodeposited CdTe thin film material on the rate of stirring of the bath electrolyte. The CdTe material was grown on glass/FTO (23 cm2) and glass/FTO/CdS (23 cm2) surfaces in bath electrolytes containing 1.0 mol/L CdSO4 and 1.0 mmol/L TeO2 solutions at different rates of stirring within the range of 0-350 rpm while keeping the values of pH of the electrolyte, deposition temperature and cathodic deposition potential with respect to the saturated calomel electrode at 2.3, 65 °C and 650 mV respectively. After the heat treatment at 400 °C in air atmosphere, the deposited samples with a good visual appearance were selected and evaluated based on their morphological, elemental, structural, optical and electrical properties in order to identify the optimum range of rate of stirring for electrodeposition of CdTe thin film semiconductors. Results revealed that, rates of stirring in the range of 60-85 rpm in a 100 mL volume of electrolyte containing the substrate and the counter electrodes in the center of the bath with a separation of 2.0 cm between them can electrodeposit CdTe layers exhibiting required levels of morphological, structural, optical and electrical properties on both glass/FTO and glass/FTO/CdS surfaces

Improvement of composition of CdTe thin films during heat treatment in the presence of CdCl2

CdCl2 treatment is a crucial step in development of CdS/CdTe solar cells. Although this rocessing step has been used over a period of three decades, full understanding is not yet achieved. This paper reports the experimental evidence for improvement of composition of CdTe layers during CdCl2 treatment. This investigation makes use of four selected analytical techniques; Photo-electro-chemical (PEC) cell, X-ray diffraction (XRD), Raman spectroscopy and Scanning electron microscopy (SEM). CdTe layers used were electroplated using three Cd precursors; CdSO4, Cd(NO3)2 and CdCl2. Results show the improvement of stoichiometry of CdTe layers during CdCl2 treatment through chemical reaction between Cd from CdCl2 and elemental Te that usually precipitate during CdTe growth, due to its natural behaviour. XRD and SEM results show that the low-temperature (~85ºC) electroplated CdTe layers consist of ~(20-60) nm size crystallites, but after CdCl2 treatment, the layers show drastic recrystallisation with grains becoming a few microns in size. These CdCl2 treated layers are then comparable to high temperature grown CdTe layers by the size of grains

Optimisation of pH of cadmium chloride post-growth-treatment in processing CDS/CDTE based thin film solar cells

The role of Chlorine-based activation in the production of high quality CdS/CdTe photovoltaic have been well discussed and explored with an overlook of the effect of Cadmium chloride (CdCl2) post-growth treatment acidity on the property of the fabricated devices. This work focuses on the optimisation of CdCl2 post-growth treatment pH as it affects both the material and fabricated device properties of all-electrodeposited multilayer glass/FTO/n-CdS/n-CdTe/p-CdTe configuration. CdCl2 treatments with acidity ranging from pH1 to pH4 were explored. The properties of the ensued CdTe layer were explored using optical, morphological, compositional structural and electrical property analysis, while, the effect on fabricated multilayer glass/FTO/n-CdS/n-CdTe/p-CdTe configuration were also explored using both I-V and C-V measurements. Highest improvements in the optical, morphological, compositional and structural were observed at pH2 CdCl2 post-growth treatment with an improvement in absorption edge, grain size, crystallinity and crystallite size. Conductivity type conversions from n-CdTe to p-CdTe, increase in pin-hole density and collapse of the absorption edge were observed after pH1 CdCl2 treatment. The highest fabricated solar cell efficiency of 13% was achieved using pH2 CdCl2 treatment as compared to other pH values explored

The Effect of Fluorine Doping on the Characteristic Behaviour of CdTe

Fluorine which is an n-type dopant of cadmium telluride thin films was included during growth from a cadmium nitrate [Cd(NO3)2Æ4H2O] bath using an electrodeposition technique. The fluorine concentration in the Cd(NO3)2Æ4H2O baths were varied between 0.5 ppm and 50 ppm in order to determine its effect on the optical, structural, morphological and electrical properties of the as-deposited and the post-growth-treated layers. These characterisations were carried out using x-ray diffraction, ultraviolet–visible spectrophotometry, scanning electron microscopy, energy dispersive x-rays spectroscopy, photoelectrochemical cell measurement, direct current conductivity measurement and fully fabricated device characterisation. The results are systematically reported in this paper

Progress in development of graded bandgap thin film solar cells with electroplated materials

Photovoltaic devices are developed mainly based on p-n or p-i-n type device structures, and these devices can utilise only a fraction of the solar spectrum. In order to further improve device parameters and move towards low-cost and high-efficiency next generation solar cells, device architectures capable of harvesting all photons available should be designed and developed. One such architecture is the fully graded bandgap device structure as proposed recently based on both n-type and p-type window layers. These designs have been experimentally tested using well researched GaAs/AlGaAs system producing impressive device parameters of open circuit voltage (Voc) ~1175 mV and fill factor (FF) ~0.85. The devices have also been experimentally tested for the evidence of impurity photovoltaic (PV) effect and impact ionisation taking place within the same device. Since these structures have been experimentally proved with a well-established semiconductor, the effort has been focussed on developing these devices using low-cost and scalable electroplated semiconductors, in order to minimise manufacturing cost. This paper reviews and summarises the work carried out during the past decade on this subject. Graded bandgap devices produced using only two or three electroplated semiconductor layers have been explored and their conversion efficiencies have gradually increased from 10.0%, through 12.8% to 15.3% for different structures. While the work is progressing along this line, the paper summarises the achievements to date

Electrodeposition and characterisation of CdS thin films using thiourea precursor for application in solar cells

CdS thin films have been successfully electrodeposited on glass/FTO substrates using acidic and aqueous solution of CdCl2.xH2O and thiourea (SC(NH2)2). The electrodeposition of CdS thin films were carried out potentiostatically using a 2-electrode system. The prepared films were characterised using X-ray diffraction (XRD), Raman spectroscopy, Scanning electron microscopy (SEM), Atomic force microscopy (AFM), Photoelectrochemical (PEC) cell measurements, Electrical resistivity measurements and UV-Vis spectrophotometry to study their structural, compositional, morphological, electrical and optical properties, respectively. The structural studies show that the as-deposited and annealed CdS layers are polycrystalline with hexagonal crystal structure and preferentially oriented along (200) planes. The optical studies indicate that the ED-CdS layers have direct bandgaps in the range (2.53-2.58) eV for the as-deposited and (2.42-2.48) eV after annealing at 400oC for 20 minutes in air. The morphological studies show the good coverage of the FTO surface by the CdS grains. The average grain sizes for the as-deposited and annealed layers were in the range (60-225) nm. These grains or clusters are made out of smaller nano crystallites with the sizes in the range ~(11-33) nm. The electrical resistivity shows reduction as thickness increases. The resistivity values for the as-deposited and annealed layers were in the range (0.82-4.92)×105 Ωcm. The optimum growth voltage for the CdS thin films was found to be at the cathodic potential of 797 mV with respect to the graphite anode. No visible precipitations of elemental S or CdS particles were observed in the deposition electrolyte showing a stable bath using thiourea during the growth

Bioactive Compounds of Rambutan (Nephelium lappaceum L.)

Rambutan, a widely popular tropical fruit encompasses rich amount of bioactive compounds. All parts of this plant (leaves, bark, root, fruits, fruit skin, pulp and seeds) finds traditional usage, and are linked with high therapeutic values. Rambutan fruits parts like that of peel, pulp and seeds have been scientifically investigated in-depth and is reported to encompass high amounts of bioactive compounds (such as polyphenol, flavonoid, alkaloid, essential mineral, dietary fiber). These compounds contribute towards antioxidant, antimicrobial, anticancer, antidiabetic and anti-obesity activities. However, literature pertaining towards potential industrial applications (food, cosmetics, pharmaceutical) of rambutan fruits are limited. In the present chapter, it is intended to document some of the interesting research themes published on rambutan fruits, and identify the existing gaps to open up arena for future research work.This chapter theme is based on our ongoing project—VALORTECH, which has received funding from the European Union’s Horizon 2020 research and innovation program under grant agreement No 810630

Application of FTIR spectroscopy for the determination of virgin coconut oil in binary mixtures with olive oil and palm oil.

Rapid Fourier transform infrared (FTIR) spectroscopy combined with attenuated total reflectance (ATR) was applied for quantitative analysis of virgin coconut oil (VCO) in binary mixtures with olive oil (OO) and palm oil (PO). The spectral bands correlated with VCO, OO, PO; blends of VCO and OO; VCO and PO were scanned, interpreted, and identified. Two multivariate calibration methods, partial least square (PLS) and principal component regression (PCR), were used to construct the calibration models that correlate between actual and FTIR-predicted values of VCO contents in the mixtures at the FTIR spectral frequencies of 1,120–1,105 and 965–960 cm−1. The calibration models obtained were cross validated using the “leave one out” method. PLS at these frequencies showed the best calibration model, in terms of the highest coefficient of determination (R 2) and the lowest of root mean standard error of calibration (RMSEC) with R 2 = 0.9992 and RMSEC = 0.756, respectively, for VCO in mixture with OO. Meanwhile, the R 2 and RMSEC values obtained for VCO in mixture with PO were 0.9996 and 0.494, respectively. In general, FTIR spectroscopy serves as a suitable technique for determination of VCO in mixture with the other oils

Service Choreography, SBVR, and Time

We propose the use of structured natural language (English) in specifying service choreographies, focusing on the what rather than the how of the required coordination of participant services in realising a business application scenario. The declarative approach we propose uses the OMG standard Semantics of Business Vocabulary and Rules (SBVR) as a modelling language. The service choreography approach has been proposed for describing the global orderings of the invocations on interfaces of participant services. We therefore extend SBVR with a notion of time which can capture the coordination of the participant services, in terms of the observable message exchanges between them. The extension is done using existing modelling constructs in SBVR, and hence respects the standard specification. The idea is that users - domain specialists rather than implementation specialists - can verify the requested service composition by directly reading the structured English used by SBVR. At the same time, the SBVR model can be represented in formal logic so it can be parsed and executed by a machine

Urban surface temperature behaviour and heat island effect in a tropical planned city

 Putrajaya is a model city planned with concepts of a "city in the garden" and an "intelligent city" in the tropics. This study presents the behaviour of the surface temperature and the heat island effect of Putrajaya. Findings show that heat island intensity is 2 °C on average at nighttime and negligible at daytime. But high surface temperature values were recorded at the main boulevard due to direct solar radiation incident, street orientation in the direction of northeast and southwest and low building height-to-street width ratio. Buildings facing each other had cooling effect on surfaces during the morning and evening hours; conversely, they had a warming effect at noon. Clustered trees along the street are effective in reducing the surface temperature compared to scattered and isolated trees. Surface temperature of built up areas was highest at noon, while walls and sidewalks facing northwest were hottest later in the day. Walls and sidewalks that face northwest were warmer than those that face southeast. The surface temperatures of the horizontal street surfaces and of vertical façades are at acceptable levels relative to the surface temperature of similar surfaces in mature cities in subtropical, temperate and Mediterranean climates. © 2014 Springer-Verlag Wien