Sugar-based bicyclic monomers for aliphatic polyesters: a comparative appraisal of acetalized alditols and isosorbide

Three series of polyalkanoates (adipates, suberates and sebacates) were synthesized using as monomers three sugar-based bicyclic diols derived from D-glucose (Glux-diol and isosorbide) and D-mannose (Manx-diol). Polycondensations were conducted in the melt applying similar reaction conditions for all cases. The aim was to compare the three bicyclic diols regarding their suitability to render aliphatic polyesters with enhanced thermal and mechanical properties. The ensuing polyesters had molecular weights (Mw) in the 25,000–50,000 g mol-1 range with highest values being attained for Glux-diol. All the polyesters started to decompose above 300 °C and most of them did not display perceivable crystallinity. On the contrary, they had glass transition temperatures much higher than usually found in homologous polyesters made of alkanediols, and showed a stress– strain behavior consistent with their Tg values. Glux-diol was particularly effective in increasing the Tg and to render therefore polyesters with high elastic modulus and considerable mechanical strength.Peer ReviewedPostprint (published version

Triblock copolyesters derived from lactic acid and glucose: synthesis, nanoparticle formation and simulation

ABA triblock copolyesters were synthesized by ring-opening polymerization (ROP) of l-lactide in solution initiated by a telechelic d-glucose-based polyester macroinitiator. The macroinitiator with a number-average molecular weight about 2500 g mol-1 was synthesized by non-stoichiometric polycondensation in the melt of 2,4:3,5-di-O-methylene-d-glucitol and dimethyl succinate. Two triblock copolyesters of Mn ranging between ~6000 and ~9000 g mol-1, and differing in the length of the polylactide blocks were prepared. These copolyesters started to decompose when heated at ~220 °C and degraded slowly upon aqueous incubation under physiological conditions. They did not display any perceivable crystallinity and showed a single glass transition temperature (Tg) around 60 °C with the higher value corresponding to the larger content in glucitol units. The copolyesters were able to form nanoparticles with average diameters of ~100–130 nm and satisfactory dispersity. The effect of the block lengths on size, ¿-potential values and physical stability of the nanoparticles was evaluated. A molecular dynamics simulation study allowed modelling the two-phase structure of the nanoparticles and evidenced the preference of the glucose-based block to be peripherally located.Peer ReviewedPostprint (author's final draft

Hydroxyl-functionalized amphiphilic triblock copolyesters made of tartaric and lactic acids: Synthesis and nanoparticle formation

Bio-based triblock copolyesters were synthesized by ring-opening polymerization of l-lactide in solution using a hydroxyl-ended polytartrate as di-functional macroinitiator. This telechelic polyester with a Mn about 3000¿g·mol-1 was obtained by non-stoichiometric melt polycondensation of dimethyl 2,3-di-O-isopropylidene-l-tartrate and 1,4-butanediol. Two symmetrical triblock copolyesters with Mn in the 5000–7000¿g·mol-1 range and differing in the length of the polylactide blocks were prepared. The protecting isopropylidene group was removed in trifluoracetic acid to generate amphiphilic triblock copolyesters bearing free hydroxyl groups in the central block. All copolyesters started to decompose approximately at 260–280¿°C, were semicrystalline, and readily degraded by hydrolysis of the main chain under both acid and basic conditions. The acetalized copolyesters had a single Tg, whereas free-hydroxyl bearing copolyesters showed two Tg indicative of blocks phase separation. All copolyesters were able to form nanoparticles with average diameters within the ~200–450¿nm range. The influence of the block lengths and protection/deprotection of the hydroxyl groups on size and ¿-potential of the nanoparticles was evaluated.Peer ReviewedPostprint (author's final draft

Isomannide-containing poly(butylene 2,5-furandicarboxylate) copolyesters via ring opening polymerization

Cyclic oligomers of isomannide 2,5-furandicarboxylate were synthesized using the high dilution condensation method. A mixture of dimer, trimer, and tetramer species largely enriched in dimer was obtained. These cyclic oligomers were made to react with oligo(butylene 2,5-furandicarboxylate) in bulk at 220 °C by ring opening polymerization using Sn(Oct)2 as a catalyst. A series of random poly(butylene 2,5-furandicarboxylate) copolyesters containing isomannide in a range of 5–50 mol % and with weight-average molecular weights between 30,000 and 50,000 g·mol–1 were prepared. These copolyesters started to decompose above 300 °C, and only those containing less than 10 mol % of isomannide showed signs of crystallinity. They displayed glass-transition temperatures in the 40–100 °C range with values increasing steadily with the content in isomannide. At difference with poly(butylene 2,5-furandicarboxylate) homopolyester that is reluctant to undergo hydrolysis, the isomannide-containing copolyesters were noticeably degraded by water, much more rapidly when exposed to lipases.Peer ReviewedPostprint (author's final draft