Journal Staff

In this study, the influuence from crystal orientation on the thermomehanical fatigue (TMF) behaviour of the recently developed single-rystal superalloy STAL-15 is considered, both from an experimental and a nite element (FE) perspective. Experimental results show that there is a strong inuence from the elastic stiffness, with respect to the loading direction, on the TMF life. However, the results also indicate that the number of active slip planes duringdeformation inuence the TMF life, where specimens with a higher number of active slip planes are favoured compared to specimens with fewer active slip planes. The higher number of active slip planes results in a more widespread deformation compared to a more conentrated deformation when only one slip plane is active. Deformation bands with smeared and elongated  γ-precipitates together with deformation twinning were found to be major deformation mechanisms, where the twins primarily were observed in specimens with several active slip planes. From an FE-perspective, therystal orientation with respect to the loading direction is quantied and adopted into a framework which makes it possible to describe the internal crystallographic arrangement and its entities in a material model. Further, a material model which incorporates the crystalorientation is able to predict the number of slip planes observed from microstructural observations, as well as the elasticstiness of the material with respect to the loading direction.On the day of the defence day the status of this article was Manuscript.The work has been financially supported by Siemens Industrial Turbomachinery AB in Finspang, Sweden, and the Swedish Energy Agency, via the Research Consortium of Materials Technology for Thermal Energy Processes, Grant no. KME-702. In addition, the support from the Swedish Government Strategic Research Area in Materials Science on Functional Materials at Linkoping University (Faculty Grant SFO-Mat-LiU #2009-00971) is also acknowledged.</p

Time- and cycle-dependent crack propagation in Haynes 282

Haynes 282 is a promising superalloy candidate for several high-temperature applications in both aero and land-based gas turbine engines. To study the crack growth behaviour under time-dependent conditions relevant to such applications, a test program was carried out at room temperature up to 700 °C with conditions ranging from pure cyclic to sustained tensile loading. At 650 °C and high stress intensity factors the crack growth was fully time-dependent for dwell-times of 90 s and longer. At lower stress intensities, the behaviour was mainly controlled by the cyclic loading, even under dwell conditions. The behaviour under dwell-fatigue conditions was well described by a liner superposition model. The main crack growth occurred transgranularly at room temperature and there was a transition in cracking behaviour from cycle dependent transgranular growth to time-dependent intergranular propagation at dK=45 MPa m^0.5 for the high temperature tests. No effect of cyclic frequency could be observed at room temperature, and at lower frequencies the crack growth rate increased with temperature

THE EFFECT OF NOTCHES ON THE FATIGUE LIFE OF A NICKEL-BASE GAS TURBINE DISK MATERIAL

Gas turbine disks carry significant load under high temperatures and may be subject to fatigue failure. Disks contain several notches in the form of the fir tree blade attachments. Low cycle fatigue tests were performed on blunt notch compact tension specimens made from alloy 718. The results indicated that notch support needed to be incorporated not to cause an overly conservative life prediction. The notch support diminished as the plastic strain range decreased, indicating that notch support is only present in the low cycle fatigue regime. A critical distance approach was applied to account for the notch support. An equation relating the critical distance to the notch root stress was derived. The chosen life model was formulated in terms of a variation on the Smith–Watson–Topper (SWT) parameter. The modified SWT parameter taken at the critical distance was used in a life model calibrated for smooth specimens to successfully predict the fatigue life of notched specimens

Відбиття в українській діалектній лексиці дохристиянської релігії слов’ян

In this study, the difference between in-phase (IP) and out-of-phase (OP) thermomechanical fatigue (TMF) cycling from 100 to 750 °C has been investigated for the Ni-based single-crystal superalloy MD2. In addition, two different crystal orientations were studied, the ⟨001⟩ and ⟨011⟩ orientations respectively. When comparing IP and OP TMF lives, a strain range dependency is found for the ⟨001⟩ direction. For high strain ranges, IP cycling leads to a higher number of cycles to failure compared to OP. However at lower strain ranges, OP cycling leads to a higher number of cycles to failure compared to IP. Microstructure investigation shows that for the ⟨001⟩ direction, deformation twinning within the γ/γ′-microstructure is much more pronounced during OP conditions compared to IP. However for the ⟨011⟩ direction, the opposite is observed; twinning is more pronounced during IP TMF. From the microstructure investigation it is also visible that intersections between twins seems to trigger formation of TCP phases and recrystallization. These intersections also work as initiation points for TMF damage

On the strengthening and embrittlement mechanisms of an additively manufactured Nickel-base superalloy

The γ′ phase strengthened Nickel-base superalloy is one of the most significant dual-phase alloy systems for high-temperature engineering applications. The tensile properties of laser powder-bed-fused IN738LC superalloy in the as-built state have been shown to have both good strength and ductility compared with its post-thermal treated state. A microstructural hierarchy composed of weak texture, sub-micron cellular structures and dislocation cellular walls was promoted in the as-built sample. After post-thermal treatment, the secondary phase γ′ precipitated with various size and fraction depending on heat treatment process. For room-temperature tensile tests, the dominated deformation mechanism is planar slip of dislocations in the as-built sample while dislocations bypassing the precipitates via Orowan looping in the γ′ strengthened samples. The extraordinary strengthening effect due to the dislocation substructure in the as-built sample provides an addition of 372 MPa in yield strength. The results of our calculation are in agreement with experimental yield strength for all the three different conditions investigated. Strikingly, the γ′ strengthened samples have higher work hardening rate than as-built sample but encounter premature failure. Experimental evidence shows that the embrittlement mechanism in the γ′ strengthened samples is caused by the high dislocation hardening of the grain interior region, which reduces the ability to accommodate further plastic strain and leads to premature intergranular cracking. On the basis of these results, the strengthening micromechanism and double-edge effect of strength and ductility of Nickel-base superalloy is discussed in detail

Cyclic Deformation Behavior of Additive-Manufactured IN738LC Superalloys from Virgin and Reused Powders

In laser powder bed fusion (L-PBF), most powders are not melted in the chamber and collected after the printing process. Powder reuse is appreciable without sacrificing the mechanical properties of target components. To understand the influences of powder reuse on mechanical performance, a nickel-based superalloy, IN738LC, was investigated. Powder morphology, microstructure and chemical compositions of virgin and reused powders were characterized. An increase in oxygen content, generally metallic oxides, was located on the surface of powders. Monotonic tensile and cyclic fatigue were tested. Negligible deterioration in strength and tensile ductility were found, while scattered fatigue performance with regard to fatigue life was shown. Deformation and fatigue crack propagation mechanisms were discussed for describing the powder degradation effects

Nano-scale characterization of white layer in broached Inconel 718

The formation mechanism of white layers during broaching and their mechanical properties are not well investigated and understood to date. In the present study, multiple advanced characterization techniques with nano-scale resolution, including transmission electron microscopy (TEM), transmission Kikuchi diffraction (TKD), atom probe tomography (APT) as well as nano-indentation, have been used to systematically examine the microstructural evolution and corresponding mechanical properties of a surface white layer formed when broaching the nickel-based superalloy Inconel 718. TEM observations showed that the broached white layer consists of nano-sized grains, mostly in the range of 20–50 nm. The crystallographic texture detected by TKD further revealed that the refined microstructure is primarily caused by strong shear deformation. Co-located Al-rich and Nb-rich fine clusters have been identified by APT, which are most likely to be γ′ and γ′′ clusters in a form of co-precipitates, where the clusters showed elongated and aligned appearance associated with the severe shearing history. The microstructural characteristics and crystallography of the broached white layer suggest that it was essentially formed by adiabatic shear localization in which the dominant metallurgical process is rotational dynamic recrystallization based on mechanically-driven subgrain rotations. The grain refinement within the white layer led to an increase of the surface nano-hardness by 14% and a reduction in elastic modulus by nearly 10% compared to that of the bulk material. This is primarily due to the greatly increased volume fraction of grain boundaries, when the grain size was reduced down to the nanoscale

Effect of layer thickness on spatter properties during laser powder bed fusion of Ti–6Al–4V

High layer thicknesses for laser powder bed fusion are promising for productivity increase. However, these are associated with increased process instability, spatter generation and powder degradation, crucial for alloys sensitive to oxygen. The effect of increasing layer thickness from 30 to 60 \ub5m is studied focusing on Ti-6Al-4V spatter formation during LPBF and its characterisation, with scanning and transmission electron microscopy, combustion analysis and X-ray photoelectron spectroscopy. Results indicate that spatters are covered with a uniform Ti-Al-based oxide layer and Al-rich oxide particulates, the thickness of which is about twice that present on virgin powder. The oxygen content was about 60% higher in spatters compared to the virgin powder. The study highlights that increasing the layer thickness to 60 \ub5m permits to reduce the total generation of spatters by ∼40%, while maintaining similar spatter characteristics and static tensile properties. Hence, this allows to increase build rate without compromising process robustness

Predicting the Microstructural Evolution of Electron Beam Melting of Alloy 718 with Phase-Field Modeling

Electron beam melting (EBM) is a powder bed additive manufacturing process where a powder material is melted selectively in a layer-by-layer approach using an electron beam. EBM has some unique features during the manufacture of components with high-performance superalloys that are commonly used in gas turbines such as Alloy 718. EBM has a high deposition rate due to its high beam energy and speed, comparatively low residual stresses, and limited problems with oxidation. However, due to the layer-by-layer melting approach and high powder bed temperature, the as-built EBM Alloy 718 exhibits a microstructural gradient starting from the top of the sample. In this study, we conducted modeling to obtain a deeper understanding of microstructural development during EBM and the homogenization that occurs during manufacturing with Alloy 718. A multicomponent phase-field modeling approach was combined with transformation kinetic modeling to predict the microstructural gradient and the results were compared with experimental observations. In particular, we investigated the segregation of elements during solidification and the subsequent “in situ” homogenization heat treatment at the elevated powder bed temperature. The predicted elemental composition was then used for thermodynamic modeling to predict the changes in the continuous cooling transformation and time–temperature transformation diagrams for Alloy 718, which helped to explain the observed phase evolution within the microstructure. The results indicate that the proposed approach can be employed as a valuable tool for understanding processes and for process development, including post-heat treatments