Melt Spinning of the Fine PEEK Filaments

The production of fine filaments using the melt spinning process needs considerable effort. A thermoplastic melt is stretched from the spinneret under a constant take-up speed. The high performance thermoplastic PEEK is solidified in the melt spinning process in a small distance and short time. Therefore, the fine PEEK filaments in the fibre formation zone underwent a high deformation and cooling rate. To make the melt spinning process stable and to produce the fine PEEK filaments, material properties and material behaviour are examined using on-line and off-line measurements. The fibre speed measured using Laser Doppler Anemometry and simultaneous temperature measured using infrared thermography enable both the strain rate and consequently the apparent extensional viscosity to be estimated. This provides the apparent extensional viscosity over the spinning line, which can itself show the structural development of PEEK fibres in the fibre formation zone, i.e. necking and solidification phenomena. The one-dimensional fibre formation model must include both procedural and material parameters. The heat transfer coefficient was estimated using the filament temperature measurement and showed a relatively high contribution of radiation and free convection in comparison to forced convection near the spinneret. The improved model of PEEK fibre formation gave a good agreement to both temperature and speed measurements, and also confirmed the high deformation rate effect on the extensional viscosity, which could be simulated with a properly generalised Newtonian constitutive equation. The end properties of the fibres, such as as-spun filament fineness, orientation (expressed using total birefringence) and total crystallisation (examined using DSC) are investigated in relation to different spinning conditions, i.e. take-up speed, throughput and the draw down ratio. The tensile test diagram results, measuring phenomena such as the elongation at break, tenacity, and the Young modulus of elasticity are also analysed in order to complete the correlation of the above-mentioned spinning conditions to the structural properties of as-spun fine PEEK filaments. The melt spinning of fine PEEK fibres under different spinning conditions is examined with the purpose of finding the optimum take-up speed and throughputs. Other spinning conditions, such as the temperature of melt processing, and the arrangement and diameter of the spinneret holes, are changed in order to make the process more stable. The recommendations for further study can be used to further examine some aspects of this work; however, this work presents a new concept for fine PEEK melt spinning supported by spinnability examinations under different spinning conditions and the improved model of fibre formation, which is also relevant for typical industrial processing applications

Odontogenic Tumors: A Challenge for Clinical Diagnosis and an Opportunity for AI Innovation

The advancement of artificial intelligence (AI) has opened up new possibilities for medical diagnosis and treatment. In particular, AI algorithms have demonstrated remarkable potential in analyzing patient radiology images and histopathological samples, offering insights that can enhance clinical decision-making [1]. This letter explores the emerging role of AI in the diagnosis and treatment of odontogenic tumors (OTs), a group of benign, malignant, and tumor-like malformations arising from the remnants of the tooth-forming apparatus

Reactivity of [Re\u3csub\u3e2\u3c/sub\u3e(CO)\u3csub\u3e8\u3c/sub\u3e(MeCN)\u3csub\u3e2\u3c/sub\u3e] with Thiazoles: Hydrido Bridged Dirhenium Compounds Bearing Thiazoles in Different Coordination Modes

Reactions of the labile compound [Re2(CO)8(MeCN)2] with thiazole and 4-methylthiazole in refluxing benzene afforded the new compounds [Re2(CO)7{μ-2,3-η2-C3H(R)NS}{η1-NC3H2(4-R)S}(μ-H)] (1, R = H; 2, R = CH3), [Re2(CO)6{μ-2,3-η2-C3H(R)NS}{η1-NC3H2(4-R)S}2(μ-H)] (3, R = H; 4, R = CH3) and fac-[Re(CO)3(Cl){η1-NC3H2(4-R)S}2] (5, R = H; 6, R = CH3). Compounds 1 and 2 contain two rhenium atoms, one bridging thiazolide ligand, coordinated through the C(2) and N atoms and a η1-thiazole ligand coordinated through the nitrogen atom to the same Re as the thiazolide nitrogen. Compounds 3 and 4 contain a Re2(CO)6 group with one bridging thiazolide ligand coordinated through the C(2) and N atoms and two N-coordinated η1-thiazole ligands, each coordinated to one Re atom. A hydride ligand, formed by oxidative-addition of C(2)–H bond of the ligand, bridges Re–Re bond opposite the thiazolide ligand in compounds 1–4. Compound 5 contains a single rhenium atom with three carbonyl ligands, two N-coordinated η1-thiazole ligands and a terminal Cl ligand. Treatment of both 1 and 2 with 5 equiv. of thiazole and 4-methylthiazole in the presence of Me3NO in refluxing benzene afforded 3 and 4, respectively. Further activation of the coordinated η1-thiazole ligands in 1–4 is, however, unsuccessful and results only nonspecific decomposition. The single-crystal XRD structures of 1–5 are reported

Assessment of failure toughening mechanisms in continuous glass fiber thermoplastic laminates subjected to cyclic loading

The final publication is available at Elsevier via https://dx.doi.org/10.1016/j.compositesb.2018.10.065 © 2019. This manuscript version is made available under the CC-BY-NC-ND 4.0 license https://creativecommons.org/licenses/by-nc-nd/4.0/Tensile fatigue behaviour of glass fiber/polyamide composites, including unidirectional ([0]8, [90]8) and cross-ply ([02/902]s, [04/904]s and [904/04]s) laminates, was studied and compared to that of similar glass fiber/epoxy composites. The fatigue resistance of cross-ply glass/polyamide was greater than that of glass/epoxy while also exhibiting lower stiffness reduction. To explain this key observation, residual stiffness and residual strength fatigue tests were performed on cross-ply laminates, while optical microscopy was used to measure ply crack density during the different stages of cycling. Testing of the cross-ply laminates at lower peak stresses of 50% of the ultimate tensile strength (i.e., high cycle fatigue regime) revealed partial cracks that did not propagate completely through the width and thickness of plies due to high matrix toughness and other observed toughening mechanisms such as matrix bridging. A micromechanical finite element model with explicit ply cracks was also used to predict laminate stiffness degradation corresponding to observed ply crack densities, revealing that stiffness degradation was overpredicted when cracks were assumed to span the entire specimen width. Additional finite element simulations with partial cracks showed notably less stiffness reduction. These observations suggest glass/polyamide is inherently more damage tolerant than glass/epoxy and may be a suitable replacement for fatigue critical structures.University of Waterlo

Crop Updates 2005 - Cereals

This session covers thirty six papers from different authors: WHEAT AGRONOMY 1. Optimum sowing time of new wheat varieties in Western Australia, Darshan Sharma, Brenda Shackley, Mohammad Amjad, Christine M. Zaicou-Kunesch and Wal Anderson, Department of Agriculture 2. Wheat varieties updated in ‘Flowering Calculator’: A model predicting flowering time, B. Shackley, D. Tennant, D. Sharma and C.M. Zaicou-Kunesch, Department of Agriculture 3. Plant populations for wheat varieties, Christine M. Zaicou-Kunesch, Wal Anderson, Darshan Sharma, Brenda Shackley and Mohammad Amjad, Department of Agriculture 4. New wheat cultivars response to fertiliser nitrogen in four major agricultural regions of Western Australia, Mohammad Amjad, Wal Anderson, Brenda Shackley, Darshan Sharma and Christine Zaicou-Kunesch, Department of Agriculture 5. Agronomic package for EGA Eagle Rock, Steve Penny, Department of Agriculture 6. Field evaluation of eastern and western wheats in large-scale farmer’s trials, Mohammad Amjad, Ben Curtis and Veronika Reck, Department of Agriculture 7. New wheat varieties for a changing environment, Richard Richards, CSIRO Plant Industry; Canberra 8. Farmers can profitably minimise exposure to frost! Garren Knell, Steve Curtin and David Sermon, ConsultAg 9. National Variety Trials, Alan Bedggood, Australian Crops Accreditation System; Horsham 10. Preharvest-sprouting tolerance of wheat in the field, T.B. Biddulph1, T.L. Setter2, J.A. Plummer1 and D.J. Mares3; 1Plant Biology; FNAS, University of Western Australia; 2Department of Agriculture, 3School of Agriculture and Wine, University of Adelaide 11. Waterlogging induces high concentration of Mn and Al in wheat genotypes in acidic soils, H. Khabaz-Saberi, T. Setter, I. Waters and G. McDonald, Department of Agriculture 12. Agronomic responses of new wheat varieties in the Northern Agricultural Region, Christine M. Zaicou-Kunesch and Wal Anderson, Department of Agriculture 13. Agronomic responses of new wheat varieties in the Central Agricultural Region of WA, Darshan Sharma, Steve Penny and Wal Anderson, Department of Agriculture 14. EGA Eagle Rock tolerance to metribuzin and its mixtures, Harmohinder Dhammu, David Nicholson and Chris Roberts, Department of Agriculture 15. Herbicide tolerance of new bread wheats, Harmohinder Dhammu1 and David Nicholson2, Department of Agriculture NUTRITION 16. The impact of fertiliser placement, timing and rates on nitrogen-use efficiency, Stephen Loss, CSBP Ltd 17. Cereals deficient in potassium are most susceptible to some leaf diseases, Ross Brennan and Kith Jayasena, Department of Agriculture 18. Responses of cereal yields to potassium fertiliser type, placement and timing, Eddy Pol, CSBP Limited 19. Sulphate of Potash, the potash of choice at seeding, Simon Teakle, United Farmers Co-operative 20. Essential disease management for successful barley production, K. Jayasena, R. Loughman, C. Beard, B. Paynter, K. Tanaka, G. Poulish and A. Smith, Department of Agriculture 21. Genotypic differences in potassium efficiency of wheat, Paul Damon and Zed Rengel, Faculty of Natural and Agricultural Sciences, University of Western Australia 22. Genotypic differences in potassium efficiency of barley, Paul Damon and Zed Rengel, Faculty of Natural and Agricultural Sciences, University of Western Australia 23. Investigating timing of nitrogen application in wheat, Darshan Sharma and Lionel Martin, Department of Agriculture, and Muresk Institute of Agriculture, Curtin University of Technology 24. Nutrient timing requirements for increased crop yields in the high rainfall cropping zone, Narelle Hill, Ron McTaggart, Dr Wal Anderson and Ray Tugwell, Department of Agriculture DISEASES 25. Integrate strategies to manage stripe rust risk, Geoff Thomas, Robert Loughman, Ciara Beard, Kith Jayasena and Manisha Shankar, Department of Agriculture 26. Effect of primary inoculum level of stripe rust on variety response in wheat, Manisha Shankar, John Majewski and Robert Loughman, Department of Agriculture 27. Disease resistance update for wheat varieties in WA, M. Shankar, J.M. Majewski, D. Foster, H. Golzar, J. Piotrowski and R. Loughman, Department of Agriculture 28. Big droplets for wheat fungicides, Rob Grima, Agronomist, Elders 29. On farm research to investigate fungicide applications to minimise leaf disease impacts in wheat, Jeff Russell and Angie Roe, Department of Agriculture, and Farm Focus Consultants PESTS 30. Rotations for nematode management, Vivien A. Vanstone, Sean J. Kelly, Helen F. Hunter and Mena C. Gilchrist, Department of Agriculture 31. Investigation into the adaqyacy of sealed farm silos in Western Australia to control phosphine-resistant Rhyzopertha dominica, C.R. Newman, Department of Agriculture 32.Insect contamination of cereal grain at harvest, Svetlana Micic and Phil Michael, Department of Agriculture 33. Phosure – Extending the life of phosphine, Gabrielle Coupland and Ern Kostas, Co-operative Bulk Handling SOIL 34. Optimum combinations of ripping depth and tine spacing for increasing wheat yield, Mohammed Hamza and Wal Anderson, Department of Agriculture 35. Hardpan penetration ability of wheat roots, Tina Botwright Acuña and Len Wade, School of Plant Biology, University of Western Australia MARKETS 36. Latin America: An emerging agricultural powerhouse, Ingrid Richardson, Food and Agribusiness Research, Rabobank; Sydne

Melt Spinning of the Fine PEEK Filaments

The production of fine filaments using the melt spinning process needs considerable effort. A thermoplastic melt is stretched from the spinneret under a constant take-up speed. The high performance thermoplastic PEEK is solidified in the melt spinning process in a small distance and short time. Therefore, the fine PEEK filaments in the fibre formation zone underwent a high deformation and cooling rate. To make the melt spinning process stable and to produce the fine PEEK filaments, material properties and material behaviour are examined using on-line and off-line measurements. The fibre speed measured using Laser Doppler Anemometry and simultaneous temperature measured using infrared thermography enable both the strain rate and consequently the apparent extensional viscosity to be estimated. This provides the apparent extensional viscosity over the spinning line, which can itself show the structural development of PEEK fibres in the fibre formation zone, i.e. necking and solidification phenomena. The one-dimensional fibre formation model must include both procedural and material parameters. The heat transfer coefficient was estimated using the filament temperature measurement and showed a relatively high contribution of radiation and free convection in comparison to forced convection near the spinneret. The improved model of PEEK fibre formation gave a good agreement to both temperature and speed measurements, and also confirmed the high deformation rate effect on the extensional viscosity, which could be simulated with a properly generalised Newtonian constitutive equation. The end properties of the fibres, such as as-spun filament fineness, orientation (expressed using total birefringence) and total crystallisation (examined using DSC) are investigated in relation to different spinning conditions, i.e. take-up speed, throughput and the draw down ratio. The tensile test diagram results, measuring phenomena such as the elongation at break, tenacity, and the Young modulus of elasticity are also analysed in order to complete the correlation of the above-mentioned spinning conditions to the structural properties of as-spun fine PEEK filaments. The melt spinning of fine PEEK fibres under different spinning conditions is examined with the purpose of finding the optimum take-up speed and throughputs. Other spinning conditions, such as the temperature of melt processing, and the arrangement and diameter of the spinneret holes, are changed in order to make the process more stable. The recommendations for further study can be used to further examine some aspects of this work; however, this work presents a new concept for fine PEEK melt spinning supported by spinnability examinations under different spinning conditions and the improved model of fibre formation, which is also relevant for typical industrial processing applications

Melt Spinning of the Fine PEEK Filaments

The production of fine filaments using the melt spinning process needs considerable effort. A thermoplastic melt is stretched from the spinneret under a constant take-up speed. The high performance thermoplastic PEEK is solidified in the melt spinning process in a small distance and short time. Therefore, the fine PEEK filaments in the fibre formation zone underwent a high deformation and cooling rate. To make the melt spinning process stable and to produce the fine PEEK filaments, material properties and material behaviour are examined using on-line and off-line measurements. The fibre speed measured using Laser Doppler Anemometry and simultaneous temperature measured using infrared thermography enable both the strain rate and consequently the apparent extensional viscosity to be estimated. This provides the apparent extensional viscosity over the spinning line, which can itself show the structural development of PEEK fibres in the fibre formation zone, i.e. necking and solidification phenomena. The one-dimensional fibre formation model must include both procedural and material parameters. The heat transfer coefficient was estimated using the filament temperature measurement and showed a relatively high contribution of radiation and free convection in comparison to forced convection near the spinneret. The improved model of PEEK fibre formation gave a good agreement to both temperature and speed measurements, and also confirmed the high deformation rate effect on the extensional viscosity, which could be simulated with a properly generalised Newtonian constitutive equation. The end properties of the fibres, such as as-spun filament fineness, orientation (expressed using total birefringence) and total crystallisation (examined using DSC) are investigated in relation to different spinning conditions, i.e. take-up speed, throughput and the draw down ratio. The tensile test diagram results, measuring phenomena such as the elongation at break, tenacity, and the Young modulus of elasticity are also analysed in order to complete the correlation of the above-mentioned spinning conditions to the structural properties of as-spun fine PEEK filaments. The melt spinning of fine PEEK fibres under different spinning conditions is examined with the purpose of finding the optimum take-up speed and throughputs. Other spinning conditions, such as the temperature of melt processing, and the arrangement and diameter of the spinneret holes, are changed in order to make the process more stable. The recommendations for further study can be used to further examine some aspects of this work; however, this work presents a new concept for fine PEEK melt spinning supported by spinnability examinations under different spinning conditions and the improved model of fibre formation, which is also relevant for typical industrial processing applications

Mechanical Behavior of Quasi-sinusoidal Corrugated Composite sheets

An aircraft wing needs to display different mechanical behavior in different directions. 1- stiffness in the spanwise (transverse to the corrugation) direction which enables the aerodynamic and inertial loads to be carried. 2- compliance in the chordwise (corrugation) direction which would allow shape changes and increases in surface area; whereas a corrugated sheet due to their special geometry has potential to use in morphing applications. Therefore, in this paper the mechanical behaviour of quasi-sinusoidal corrugated composites is studied by commercial FEM software ABAQUS and a simple analytical model which is used for the initial stiffness of the quasi-sinusoidal corrugated composites (Yokozeki model). The elongation and effective stiffness in longitudinal and transverse directions of quasi-sinusoidal  corrugated  skins  and fat  composites  are  calculated  and  compared together.  Using  frst  and  second  Castigliano’s  theorem  and  Bernoulli-Euler  beam theorem can be used to calculate the defection and rotational angle of a beam (sheet). In this research, different dimensions of quasi-sinusoidal element for unidirectional and woven composites of E-glass/epoxy are investigated. FEM results and analytical model are compared together. Then, the analytical model is validated by experimental results of plain woven E-glass/epoxy composites. The results of FEM, experimental and analytical simulations show that how a corrugated composite can afford with certainty larger deformation than the fat composite in using this analytical model to predict the mechanical behavior of quasi-sinusoidal corrugated composites. It was found that the corrugated composites display extremely high anisotropic behavior and have high  tensile and fexural stiffness  in  transverse direction while exhibiting  low stiffness in longitudinal direction of corrugation

Stiffness Matrices and Anisotropy in the Trapezoidal Corrugated Composite Sheets

In the some applications like as morphing technology, high strain and anisotropic behavior are essential design requirements. The corrugated composite sheets due to their special geometries have potential to high deflection under axial loading through longitudinal direction of corrugation. In this research, the strain and the anisotropic behavior of corrugated composite sheets are investigated by fabricating glass/epoxy samples with trapezoidal geometries. For evaluation of the mechanical behavior of the composites the samples were subjected to tension and flexural tests in the longitudinal and transverse directions of corrugation. In order to determine anisotropic behavior of the corrugated sheets, two approaches were introduced: (1) tensile anisotropic (E*) and (2) flexural anisotropic (D*). The anisotropic behavior and ultimate deflections were investigated theoretically and experimentally. In this paper, mechanical behaviors based on theoretical and experimental analysis including the elastic constants and stiffness matrices of trapezoidal corrugated composite sheets were studied and the results were verified by finite element method. The results of the numerical and analytical solutions were compared with those of experimental tests. Finally, the load-displacement curves of tensile tests in longitudinal direction of corrugation, the ultimate deflection and anisotropy behavior of these exclusive composite sheets in the corrugated composite sheets were studied experimentally. The experimental results of the trapezoidal corrugated sheets showed that one of the most important parameters in the ultimate strain was amplitude of the corrugation elements. Generally, increasing the amplitude and element per length unit of trapezoidal corrugated specimen led to higher ultimate strain

مسئولیت هزینه‌های درمان بیماران مبتلا به کرونا در فرض تقصیر کادر درمان

Background and Aim: The corona virus pandemic has caused widespread problems in various aspects of human life. One of the most important of these dimensions is mortality from this disease; however, advanced studies have shown that sometimes the patient's death is not directly due to the disease and medical errors such as drug interactions (poly pharmacy), lack of timely attention to the patient, inaccuracy in intubation and … led to serious injuries to the patient, as a result of which the patient lost his life. The present article seeks to determine the scope of physician or other medical staff liability in medical expenses and blood money after distinguishing their fault. Materials and Methods: the present descriptive-analytical essay based on library method has collected legal articles and jurisprudential fatwas related to the present subject and in addition to citing different viewpoints in this regard has criticized their reasons. Eventually by referring to some proofs such as causation principle, the conduct of sane minds, command of intellect and Abu-Maryam narration, proves the correct opinion. Conclusion: The medical staffs are responsible for the blood money and the extra expenses of medical treatments which have been caused due to medical errors in coronavirus cases. The costs of improper treatment measures such as harmful or unnecessary surgery and secondary treatment measures are assumed by the perpetrators if they are at fault.زمینه و هدف: با شروع همه‌گیری ویروس کرونا، مسائل و مشکلات گسترده‌ای در ابعاد مختلف زندگی بشر ایجاد شد. از مهم‌ترین این ابعاد، مرگ و میر ناشی از این بیماری است؛ هرچند با بررسی‌های پیشرفته مشخص شده است که گاهی فوت بیمار مستقیماً ناشی از بیماری نبوده و اشتباهات پزشکی از قبیل تداخل دارویی (پلی فارمسی)[1] عدم رسیدگی به موقع به وضعیت بیمار، عدم دقت در عملیات تراشه‌گذاری نای (انتوباسیون)[2] و ... منجر به صدمات جدی به بیمار شده که به تبع آن، بیمار جان خود را از دست داده است. مقاله پیش‌رو درصدد تعیین محدوده ضمان پزشک یا سایر کادر درمان در پرداخت دیه و هزینه‌های درمان، پس از احراز تقصیر و استناد جنایت است. مواد و روش‌ها: متن حاضر، براساس شیوه کتابخانه‌ای، به جمع‌آوری مواد قانونی و فتاوای فقهی مرتبط با موضوع حاضر پرداخته و به صورت توصیفی - تحلیلی علاوه بر نقل دیدگاه‌های متفاوت در این باب، به نقد ادله ایشان پرداخته است. در نهایت با استناد به ادله‌ای همچون قاعده تسبیب، سیره عقلاء و روایت ابی مریم به دنبال اثبات رأی صائب است. نتیجه‌گیری: در صورت احراز تقصیر کادر درمان در اقدامات درمانی برای بیمار مبتلا به کرونا و ورود آسیب‌های جسمانی یا فوت بیمار، دیه عضو یا نفس بر عهده مقصر است. هزینه‌های اقدامات نادرست درمانی همچون عمل جراحی زیان‌بار یا غیر ضروری و اقدامات درمانی ثانویه در فرض تقصیر بر عهده مرتکبین است.   [1]. Poly pharmacy [2]. Tracheal intubatio