Experimental and thermodynamic investigations on the chlorine-induced corrosion of HVOF thermal sprayed NiAl coatings and 304 stainless steels at 700 °C

Alumina-forming β-NiAl coatings were deposited by high Velocity Oxy-fuel (HVOF) thermal spray onto 304 stainless steels for protection against chlorine induced corrosion in a biomass-fired boiler. The corrosion test was conducted in a synthetic gas containing 500 ppm HCl with 10 wt% KCl ash deposit at 700 °C for 250 hours. Severe corrosion was observed with the fast growing alumina at the coating/substrate interface initiating from sample edges. Possible corrosion mechanism was proposed: as supplied by HCl/KCl, the formation of volatile chlorine/chloride acted as a catalyst and promoted the growth of alumina at relatively lower application temperatures (<900 °C)

Mitigation of Platinum Depletion in Platinum Diffused Single Phase Bond Coat on CMSX-4 Superalloy

Pt-diffused bond coat with a mixture of γ/γ’ phase has just been developed in the recent decades as a cheaper alternative to the Pt-enriched β-phase Aluminide bond coat that contains a higher content of Al. However, concerns are raised on the inevitable depletion of Pt near the coating interface that may endanger the component after long-term service. In this study, modified Pt-diffused bond coats with a single phase (γ or γ’) were made by applying selective etching on CMSX-4 single crystal superalloys prior to the electroplating of Pt. The single-phase bond coats show distinctive diffusion behaviour in comparison with the conventional γ/γ’ bond coat. Surprisingly, Pt remains more stable in the γ’-phase bond coat with significantly less depletion after diffusion, which implies a potential in saving a considerable amount of Pt. On the other hand, however, the depletion of Pt is more severe in the γ-phase bond coat. The mechanism that governs the diffusion behavior of Pt in the γ and γ’-phase was also discussed that mainly concerns with thermodynamic and kinetic factors

Robust hydrophobic surfaces from suspension HVOF thermal sprayed rare-earth oxide ceramics coatings

This study has presented an efficient coating method, namely suspension high velocity oxy-fuel (SHVOF) thermal spraying, to produce large super-hydrophobic ceramic surfaces with a unique micro- and nano-scale hierarchical structures to mimic natural super-hydrophobic surfaces. CeO2 was selected as coatings material, one of a group of rare-earth oxide (REO) ceramics that have recently been found to exhibit intrinsic hydrophobicity, even after exposure to high temperatures and abrasive wear. Robust hydrophobic REO ceramic surfaces were obtained from the deposition of thin CeO2 coatings (3–5 μm) using an aqueous suspension with a solid concentration of 30 wt.% sub-micron CeO2 particles (50–200 nm) on a selection of metallic substrates. It was found that the coatings’ hydrophobicity, microstructure, surface morphology, and deposition efficiency were all determined by the metallic substrates underneath. More importantly, it was demonstrated that the near super-hydrophobicity of SHVOF sprayed CeO2 coatings was achieved not only by the intrinsic hydrophobicity of REO but also their unique hierarchically structure. In addition, the coatings’ surface hydrophobicity was sensitive to the O/Ce ratio, which could explain the ‘delayed’ hydrophobicity of REO coatings

A Review on In Situ Mechanical Testing of Coatings

Real-time evaluation of materials’ mechanical response is crucial to further improve the performance of surfaces and coatings because the widely used post-processing evaluation techniques (e.g., fractography analysis) cannot provide deep insight into the deformation and damage mechanisms that occur and changes in coatings’ material corresponding to the dynamic thermomechanical loading conditions. The advanced in situ examination methods offer deep insight into mechanical behavior and material failure with remarkable range and resolution of length scales, microstructure, and loading conditions. This article presents a review on the in situ mechanical testing of coatings under tensile and bending examinations, highlighting the commonly used in situ monitoring techniques in coating testing and challenges related to such techniques

Steam Degradation of Ytterbium Disilicate Environmental Barrier Coatings: Effect of Composition, Microstructure and Temperature

Recession of environmental barrier coatings (EBC) in environments containing steam is a pressing concern that requires further research before their implementation in gas turbine engines can be realized. In this work, free-standing plasma sprayed Yb2Si2O7 coatings were exposed to flowing steam at 1350 {\deg}C and 1400 {\deg}C for 96 h. Three samples were investigated, one coating with a low porosity level (< 3 %) and 1 wt.% Al2O3 representing traditional EBCs; and two coatings with higher porosity levels (~20 %) representing abradable EBCs. Phase composition and microstructural evolution were studied in order to reveal the underlying mechanism for the interaction between high temperature steam and ytterbium disilicate. The results show depletion of Yb2SiO5 near the surface and formation of ytterbium garnet (Yb3Al5O12) on top of all three coatings due to the reaction with gaseous Al-containing impurities coming from the alumina furnace tubes. The 1 wt.% Al2O3 added to the EBC sample exacerbated the formation of garnet at 1400 {\deg}C compared to the abradable samples, which presented lower quantities of garnet. Additionally, inter-splat boundaries were visible after exposure, indicating preferential ingress of gaseous Al-containing impurities through the splat boundarie

Anisotropic plasticity mechanisms in a newly synthesised high entropy alloy investigated using atomic simulations and nanoindentation experiments

This work used atomic simulations and nanoindentation experiments to investigate hardness, modulus alongside sub-surface crystal defects and dislocation mediated plasticity mechanisms leading to anisotropic pile up and local entropy variation in high entropy alloys. The experimental campaign began from Thermo-Calc phase prediction of Ni25Cu18.75Fe25Co25Al6.25 HEA which followed experimental synthesis of the material using arc melting method and experimental nanoindentation using a Berkovich indenter under load-controlled conditions. Through MD simulations, the value of hf/hmax in monocrystalline HEA was consistently found to be larger than 0.7 which suggested pile-up behaviour to dominate and sink-in behaviour to be unlikely. In the case of (110) and polycrystalline HEA substrates, the elastic work in the indentation hysteresis loop was seen to be larger than the (100) and the (111) orientations which explains that the (110) orientation substrate showed least elastic modulus and hardness while the (111) monocrystalline HEA showed the highest elastic modulus and hardness. From the simulations, a “lasso” type loop on the (110) orientation and cross-over of shear loops on the other orientations accompanied by dislocations of type 1/6 &lt; 112 &gt; (Shockley), 1/2 &lt; 110 &gt; (perfect), 1/3 &lt; 001 &gt; (Hirth), 1/6 &lt; 110 &gt; (Stair rod) and 1/3 &lt; 111 &gt; (Frank partials) were seen to manifest an early avalanche of competing plasticity events. The defects accompanying these dislocations in the sub-surface were identified to be FCC intrinsic stacking faults (ISF), adjacent intrinsic stacking faults (quad faults), coherent ∑3 twin boundary and a coherent twin boundary next to an intrinsic stacking fault (triple fault). The EBSD analysis applied to the MD data showed that the (210) orientation and the&lt; 110 &gt; family of directions were seemed to be preferable to plastically deform the FCC phased Ni25Cu18.75Fe25Co25Al6.25 HEA.</p

Mitigation of Platinum Depletion in Platinum Diffused Single Phase Bond Coat on CMSX-4 Superalloy

From MDPI via Jisc Publications RouterHistory: accepted 2021-05-28, pub-electronic 2021-05-31Publication status: PublishedPt-diffused bond coat with a mixture of γ/γ’ phase has just been developed in the recent decades as a cheaper alternative to the Pt-enriched β-phase Aluminide bond coat that contains a higher content of Al. However, concerns are raised on the inevitable depletion of Pt near the coating interface that may endanger the component after long-term service. In this study, modified Pt-diffused bond coats with a single phase (γ or γ’) were made by applying selective etching on CMSX-4 single crystal superalloys prior to the electroplating of Pt. The single-phase bond coats show distinctive diffusion behaviour in comparison with the conventional γ/γ’ bond coat. Surprisingly, Pt remains more stable in the γ’-phase bond coat with significantly less depletion after diffusion, which implies a potential in saving a considerable amount of Pt. On the other hand, however, the depletion of Pt is more severe in the γ-phase bond coat. The mechanism that governs the diffusion behavior of Pt in the γ and γ’-phase was also discussed that mainly concerns with thermodynamic and kinetic factors

High-Entropy Coatings (HEC) for High-Temperature Applications: Materials, Processing, and Properties

High-entropy materials (HEM), including alloys, ceramics, and composites, are a novel class of materials that have gained enormous attention over the past two decades. These multi-component novel materials with unique structures always have exceptionally good mechanical properties and phase stability at all temperatures. Of particular interest for high-temperature applications, e.g., in the aerospace and nuclear sectors, is the new concept of high-entropy coatings (HEC) on low-cost metallic substrates, which has just emerged during the last few years. This exciting new virgin field awaits exploration by materials scientists and surface engineers who are often equipped with high-performance computational modelling tools, high-throughput coating deposition technologies and advanced materials testing/characterisation methods, all of which have greatly shortened the development cycle of a new coating from years to months/days. This review article reflects on research progress in the development and application of HEC focusing on high-temperature applications in the context of materials/composition type, coating process selection and desired functional properties. The importance of alloying addition is highlighted, resulting in suppressing oxidation as well as improving corrosion and diffusion resistance in a variety of coating types deposited via common deposition processes. This review provides an overview of this hot topic, highlighting the research challenges, identifying gaps, and suggesting future research activity for high temperature applications