170 research outputs found

    Evaluation of Temperature Gradients During Cure of a Thick Carbon Fiber/Epoxy Composite

    Get PDF
    The purpose of this study is to evaluate the development of thermal gradients throughout thick (1") carbon fiber composites and determine the effect of internal temperature distribution during cure on the observed mechanical properties in those composites. Composites up to 1.5" thick (56 plies) were fabricated with T700S/TC380 braided prepreg from Tencate following a modified vacuum bag layup procedure to include embedded thermocouples within the plies of the composite. Composite panels were cured in a programmable oven with thermocouple reading embedded throughout the panel thickness. Maximum temperature gradients measured between regions of the composite did not exceed 10 degrees C for any given composite thickness. The most significant temperature variation was measured between the mid-thickness plies and the tool-side surface plies. Although through thickness temperature variation during cure was small, a measureable variation in coupon glass transition temperature was recorded between the tool side plies and the remainder of the part, prior to post cure. Thermal and mechanical behavior of coupons taken from segments through the thickness of the part were comparable following a post-cure cycle

    Multifunctional Composites for Improved Polyimide Thermal Stability

    Get PDF
    The layered morphology of silicate clay provides an effective barrier to oxidative degradation of the matrix resin. However, as resin thermal stability continues to reach higher limits, development of an organic modification with comparable temperature capabilities becomes a challenge. Typically, phyllosilicates used in polymer nanocomposites are modified with an alkyl ammonium ion. Such organic modifiers are not suited for incorporation into high temperature polymers as they commonly degrade below 200oC. Therefore, the development of nanoparticle specifically suited for high temperature applications is necessary. Several nanoparticles were investigated in this study, including pre-exfoliated synthetic clay, an organically modified clay, and carbon nanofiber. Dispersion of the layered silicate increases the onset temperature of matrix degradation as well as slows oxidative degradation. The thermally stable carbon nanofibers are also observed to significantly increase the resin thermal stability

    Nanoparticle/Polymer Nanocomposite Bond Coat or Coating

    Get PDF
    This innovation addresses the problem of coatings (meant to reduce gas permeation) applied to polymer matrix composites spalling off in service due to incompatibility with the polymer matrix. A bond coat/coating has been created that uses chemically functionalized nanoparticles (either clay or graphene) to create a barrier film that bonds well to the matrix resin, and provides an outstanding barrier to gas permeation. There is interest in applying clay nanoparticles as a coating/bond coat to a polymer matrix composite. Often, nanoclays are chemically functionalized with an organic compound intended to facilitate dispersion of the clay in a matrix. That organic modifier generally degrades at the processing temperature of many high-temperature polymers, rendering the clay useless as a nano-additive to high-temperature polymers. However, this innovation includes the use of organic compounds compatible with hightemperature polymer matrix, and is suitable for nanoclay functionalization, the preparation of that clay into a coating/bondcoat for high-temperature polymers, the use of the clay as a coating for composites that do not have a hightemperature requirement, and a comparable approach to the preparation of graphene coatings/bond coats for polymer matrix composites

    Selective Clay Placement Within a Silicate-Clay Epoxy Blend Nanocomposite

    Get PDF
    A clay-epoxy nanocomposite may be prepared by dispersing a layered clay in an alkoxy epoxy, such as a polypropylene oxide based epoxide before combining the mixture with an aromatic epoxy to improve the nanocomposite's thermal and mechanical properties

    Through Thickness Thermal Gradients in Thick Laminates During Cure, Influence on Tg and Modulus

    Get PDF
    Carbon fiber composites are materials of great interest to the aerospace industry because of their light weight and high strength properties. Composite use in high load bearing applications such as roto-craft gearing requires manufacturing parts that are 1.5 inches thick and beyond. Very thick composite parts (laminates) produce thermal gradients and temperature spikes due to the heat released by resin polymerization and cross-linking during composite cure. It is believed that these thermal gradients will cause internal stresses to build-up inside these ultra-thick laminates during the cure-cycle, yielding parts with non-uniform mechanical properties throughout the thickness of the laminate. The goal of this study is to identify these thermal gradients and determine the magnitude of difference in mechanical properties generated by them

    Characterization of IM7/8552 Thin-Ply and Hybrid Thin-Ply Composites

    Get PDF
    Composite materials have increasingly been used for aerospace applications due to improved performance and reduced weight compared to their metallic counterparts. Inclusion of thin-ply material, plies with cured thickness half or less than standard composites, have potential to improve performance and reduce structural weight. Limited characterization of thin-ply IM7/8552 material in 30 and 70 grams per square meter fiber areal weights has been carried out using a series of selected American Society for Testing and Materials (ASTM) tests. Tests included unnotched tension, unnotched compression, v-notched rail shear, open-hole tension, and open-hole compression. Unidirectional, cross-ply, quasiisotropic and hybrid hard laminates were included in the study, and were compared to standard-ply laminates. Properties compared include fiber volume, laminate moduli, and failure strength, with failure modes also being examined. The thin-ply specimens exhibited similar or superior performance to standard ply laminates in many of the cases compared. Improvements in strength for laminates containing thin-ply material were seen for unidirectional laminates under unnotched tension, quasi-isotropic laminates under unnotched tension and compression, and hard laminates under open hole tension. Additional investigation is required to determine appropriate ply stacking rules for hybrids of thin and standard plies to avoid undesirable failure modes such as axial splitting. However, the observed performance improvements demonstrated by the conducted ASTM tests of hybrid thin-ply hard laminates could have benefits for improved structural weight in aircraft

    Effect of Graphene Addition on Shape Memory Behavior of Epoxy Resins

    Get PDF
    Shape memory polymers (SMPs) and composites are a special class of smart materials known for their ability to change size and shape upon exposure to an external stimulus (e.g. light, heat, pH, or magnetic field). These materials are commonly used for biomedical applications; however, recent attempts have been made towards developing SMPs and composites for use in aircraft and space applications. Implementing SMPs and composites to create a shape change effect in some aircraft structures could potentially reduce drag, decrease fuel consumption, and improve engine performance. This paper discusses the development of suitable materials to use in morphing aircraft structures. Thermally responsive epoxy SMPs and nanocomposites were developed and the shape memory behavior and thermo-mechanical properties were studied. Overall, preliminary results from dynamic mechanical analysis (DMA) showed that thermally actuated shape memory epoxies and nanocomposites possessed Tgs near approximately 168 C. When graphene nanofiller was added, the storage modulus and crosslinking density decreased. On the other hand, the addition of graphene enhanced the recovery behavior of the shape memory nanocomposites. It was assumed that the addition of graphene improved shape memory recovery by reducing the crosslinking density and increasing the elasticity of the nanocomposites

    Biaxial Braided Flared Cone Structural Analysis

    Get PDF
    Computed Tomography (CT) is a useful tool for performing structural analysis on polymer based materials due to its high precision and accuracy. CT data was taken of two flared cones made from carbon fiber and fiberglass. One of the flared cones is pictured below. The variation in braid angle throughout the part was measured using Avizo 3D modelling software while the variation in thickness throughout the part was determined using MATLAB. Samples of pictures from the process of each of these analyses are shown below. The overall goal of this analysis was to collect structural data relevant to future testing of the parts

    Polymer Matrix Composites Fabrication and Testing

    Get PDF
    This project involves two separate processes for fabricating carbon fiber composite parts using Hexcels RTM6 resin system and Kanekas IR-6070 toughened resin system to impregnate carbon fiber tow and weave. These two resins were chosen to model microcracking in parts using RTM6 compared to parts using IR-6070. Plies of the composites were made by painting resin onto 8 harness satin weave or impregnating IM7 12k tow in a prepregging machine. Plies were consolidated using an out-of-autoclave oven or a heat press. Fabrication of the composite parts were conducted with the end goal of sending the composites to be tested and modeled for microcracking. The data will be used for computer modeling in the future

    Development of Composite Sandwich Bonded Longitudinal Joints for Space Launch Vehicle Structures

    Get PDF
    The NASA Composite Technology for Exploration (CTE) Project is developing and demonstrating critical composite technologies with a focus on composite bonded joints; incorporating materials, design/analysis, manufacturing, and tests that utilize NASAs expertise and capabilities. The project has goals of advancing composite technologies and providing lightweight structures to support future NASA exploration missions. In particular, the CTE project will demonstrate weight-saving, performance-enhancing composite bonded joint technology for Space Launch System (SLS)-scale composite hardware. Advancements from the CTE project may be incorporated as future block upgrades for SLS structural components. This paper discusses the details of the development of a composite sandwich bonded longitudinal joint for a generic space launch vehicle structure called the CTE Point Design. The paper includes details of the design, analysis, materials, manufacturing, and testing of sub-element joint test articles to test the capability of the joint design. The test results show that the composite longitudinal bonded joint design significantly exceeds the design loads with a 2.0 factor of safety. Analysis pre-test failure predictions for all sub-element bonded joint test coupons were all within 10% of the average test coupon failure load. This testing and analysis provides confidence in the potential use of composite bonded joints for future launch vehicle structures
    • …
    corecore