Effect of hard and soft re-coater blade on porosity and processability of thin walls and overhangs in laser powder bed fusion additive manufacturing

Spreading powder into thin layers is a fundamental step in the laser powder bed fusion (PBF-LB) additive manufacturing process. This step is called re-coating and it is typically performed using either a hard, soft or brush-type re-coater blade or a rotating roller, depending on the machine brand and model. With such variety in powder spreading approaches, the question arises whether the used re-coater type has a significant effect on the quality of parts produced? In this study, an industrial contact image sensor integrated to the re-coater of a PBF-LB system was used for powder bed quality monitoring. Powder bed images at 21 µm/pixel resolution, 184 mm scanning width and 95 mm/s re-coating speed were acquired. With this, the effect of using either soft (rubber) or hard (steel) re-coater blade on the processability of challenging features such as thin walls and steep overhangs was studied. In addition, porosity and dimensional accuracy of parts produced using either the soft or hard blade was analyzed with X-ray computed tomography. It is shown that when building bulk material without any complex features, both the hard and soft re-coating blade results in extremely low porosity ≤ 0.001% without any issues in the processability. However, when thin walls and overhangs are produced, differences in processability, porosity and dimensional accuracy are observed as a function of re-coater blade and part orientation. This is an important factor in understanding all the significant sources contributing to the variability on quality of parts produced using different PBF-LB machines

Recycling of 3D Printable Thermoplastic Cellulose-Composite

3D printing enables sustainable product innovations through novel design, reduced use of materials, and local manufacturing. Sustainable 3D printing can further be realized using recyclable materials. Cellulose is an abundantly available renewable material. Modified celluloses, such as thermoplastic cellulose esters, are widely used in injection molding applications. The aim of this research was to study the properties of a cellulose-based composite (cellulose acetate propionate (CAP) polymer matrix with 20 wt. % microcellulose) in injection molding and granular extrusion-based 3D printing processes over multiple recycles. The impact of the processing methods on the composite’s properties were investigated. Both injection molded and 3D printed samples were ground with plastic grinding mill to particle sizes below 3 mm after each preparation stage and reused as such in the next process cycle. Morphology, mechanical and thermal properties, and material degradation were analyzed. The thermoplastic cellulose-based compound was found to be directly recyclable for both processes without the need for any additional compounding steps. The polymer matrix was able to withstand at least seven processing cycles without degradation. However, microcellulose was found to be more sensitive to thermal stress. The mechanical and thermal properties of the cellulose-based composites remained close to initial levels throughout

Digital Spare Parts

Published by Aalto University and VTT Technical Research Centre of Finland.Digital spare parts is a concept where the spare parts and the related manufacturing data are stored and transferred in digital form. The spare parts are manufactured using 3D printing according to need, usually close to the end user’s premises. The digitalisation of spare parts aims for a better, more flexible and quicker availability of spare parts, and lower storage, manufacturing and transport costs. The quicker delivery of spare parts can also reduce downtime, which can mean significant cost savings. It is essential in the digitalisation of the companies' spare parts to find the parts in the spare part libraries that bring the greatest benefit when they are stored in digital form and manufactured by 3D printing. Such parts include, in particular, parts of old equipment and machines and slowly circulating parts with complex geometries. Today, 3D printing can be used to manufacture high-performance pieces, and the method is excellently suited to the manufacturing of individual pieces or short-run batches; it also allows the improvement of the spare parts, with updated and intelligent spare parts as examples. Information on a company's spare parts is scattered between multiple systems, and manufacturing data in particular may be difficult to find. At the initial stage, it is important to identify the 3D printable parts in the spare part libraries and digitalise them, not only with regard to 3D models but all other manufacturing data from materials and tolerances to the required post-processing data. The digitalisation of spare parts requires 3D design competence, knowledge of the 3D printing processes, and familiarisation with the printable materials. Spare parts are rarely designed to be manufactured by 3D printing; on the other hand, the selection of 3D printable materials remains reasonably limited, due to which situations where a part is manufactured from a replacement material will likely occur. 3D printing processes produce their own kind of a structure and surface finish, due to which the post-processing of 3D printable parts, such as heat treatments and finishing, must be carefully chosen. The goal is that the properties of parts manufactured by 3D printing are at least as good as those of conventionally manufactured parts. The vision of the roadmap for digital spare parts presented in the report is that after ten years or so, 10% of spare parts are digital, and the manufacturing technology is reliable and is of a high quality. In other words, quality verification, the extension of the related material selection and the automation of processes are required of the 3D printing technologies. 3D printing creates new possibilities for the development of the operation of parts, equipment or entire processes. IDs and sensors can be embedded into 3D printed parts, allowing the tracking of their movement in the supply network and anticipatory condition monitoring. A spare part of the future will be able to automatically order a new part from a digital spare part library so that it can be replaced by the new part just at the right time before the machine breaks down or the process stops

Digitaaliset varaosat

Aalto-yliopiston ja Teknologian tutkimuskeskus VTT:n yhteisjulkaisu.Digitaaliset varaosat on konsepti, jossa varaosat ja niihin liittyvä valmistustieto säilytetään ja siirretään digitaalisessa muodossa. Varaosien valmistus tapahtuu 3D-tulostamalla tarpeen mukaan yleensä lähellä loppukäyttäjää. Varaosien digitalisoinnilla tavoitellaan parempaa, joustavampaa ja nopeampaa varaosien saatavuutta sekä pienempiä varastointi-, valmistus- ja kuljetuskustannuksia. Nopeammalla varaosien toimittamisella voidaan myös pienentää seisokkiaikoja, mikä voi tarkoittaa merkittäviä kustannussäästöjä. Oleellista yritysten varaosien digitalisoinnissa on löytää varaosakirjastoista ne osat, joiden säilyttämisestä digitaalisessa muodossa ja valmistamisesta 3D-tulostamalla saadaan suurin hyöty. Tällaisia osia ovat etenkin vanhojen laitteiden ja koneiden osat sekä hitaasti kiertävät osat, jotka ovat geometrialtaan monimutkaisia. 3D-tulostamalla voidaan nykypäivänä valmistaa suorituskykyisiä kappaleita ja menetelmä soveltuu erinomaisesti yksittäiskappaleiden tai pienten sarjojen valmistamiseen. Digitaalinen valmistus antaa myös mahdollisuuden kehittää varaosia, mistä esimerkkinä voidaan mainita päivitetyt ja älykkäät varaosat. Tiedot yritysten varaosista ovat hajallaan monissa järjestelmissä ja varsinkin valmistukseen liittyvää tietoa voi olla vaikea löytää. Alkuvaiheessa on tärkeää tunnistaa 3D-tulostettavat osat varaosakirjastoista ja digitalisoida osat mukaan lukien niin 3D-mallit kuin kaikki muu valmistustieto materiaaleista ja toleransseista tarvittaviin jälkikäsittelytietoihin. Varaosien digitalisointi vaatii 3D-suunnitteluosaamista sekä 3D-tulostusprosessien tuntemusta ja tulostettaviin materiaaleihin perehtymistä. Varaosia on harvoin tarkoitettu valmistettavaksi 3D-tulostamalla ja toisaalta 3D-tulostettavien materiaalien valikoima on vielä kohtuullisen rajallinen, mistä syystä joudutaan todennäköisesti tilanteisiin, joissa valmistetaan osa jostakin korvaavasta materiaalista. 3D-tulostusprosessit tuottavat omanlaista rakennetta ja pinnanjälkeä, mistä syystä myös 3D-tulostettavien osien jälkikäsittelyt kuten lämpökäsittelyt ja viimeistelyt on valittava huolellisesti. Tavoite on, että 3D-tulostamalla valmistettujen osien ominaisuudet ovat vähintään yhtä hyvät verrattuna perinteisesti valmistettuihin osiin. Raportissa esitetyn digitaalisten varaosien tiekartan visio on, että noin kymmenen vuoden päästä 10% varaosista on digitaalisia ja valmistusteknologia on luotettavaa ja laadukasta. 3D-tulostusteknologioilta edellytetään siis laadun tosittamista, niihin liittyvän materiaalikirjon laajenemista sekä prosessien automatisointia. 3D-tulostaminen avaa uusia mahdollisuuksia kehittää osien, laitteiden tai kokonaisten prosessien toimintaa. 3D-tulostettuihin osiin voidaan upottaa tunnisteita ja sensoreita, joiden avulla voidaan seurata osien liikkumista toimitusverkostossa sekä suorittaa ennakoivaa kunnonvalvontaa. Tulevaisuuden varaosa osaa tilata automaattisesti uuden osan digitaalisesta varaosakirjastosta, jolloin uusi osa saadaan vaihdetuksi kuluneen tilanne juuri oikeaan aikaan ennen koneen rikkoutumista tai prosessin pysähtymistä