414 research outputs found
Density fluctuations measured by ISEE 1-2 in the Earth's magnetosheath and the resultant scattering of radio waves
Latitudinal distribution of the solar wind properties in the low- and high-pressure regimes: Wind observations
International audienceThe solar wind properties depend on ?, the heliomagnetic latitude with respect to the heliospheric current sheet (HCS), more than on the heliographic latitude. We analyse the wind properties observed by Wind at 1 AU during about 2.5 solar rotations in 1995, a period close to the last minimum of solar activity. To determine ?, we use a model of the HCS which we fit to the magnetic sector boundary crossings observed by Wind. We find that the solar wind properties mainly depend on the modulus |?|. But they also depend on a local parameter, the total pressure (magnetic pressure plus electron and proton thermal pressure). Furthermore, whatever the total pressure, we observe that the plasma properties also depend on the time: the latitudinal gradients of the wind speed and of the proton temperature are not the same before and after the closest HCS crossing. This is a consequence of the dynamical stream interactions. In the low pressure wind, at low |?|, we find a clear maximum of the density, a clear minimum of the wind speed and of the proton temperature, a weak minimum of the average magnetic field strength, a weak maximum of the average thermal pressure, and a weak maximum of the average ß factor. This overdense sheet is embedded in a density halo. The latitudinal thickness is about 5° for the overdense sheet, and 20° for the density halo. The HCS is thus wrapped in an overdense sheet surrounded by a halo, even in the non-compressed solar wind. In the high-pressure wind, the plasma properties are less well ordered as functions of the latitude than in the low-pressure wind; the minimum of the average speed is seen before the HCS crossing. The latitudinal thickness of the high-pressure region is about 20°. Our observations are qualitatively consistent with the numerical model of Pizzo for the deformation of the heliospheric current sheet and plasma sheet
Recommended from our members
Relating hygroscopicity and optical properties to chemical composition and structure of secondary organic aerosol particles generated from the ozonolysis of α-pinene
Secondary organic aerosol (SOA) were generated from the ozonolysis of α-pinene in the CESAM (French acronym for Experimental Multiphasic Atmospheric Simulation Chamber) simulation chamber. The SOA formation and aging were studied by following their optical, hygroscopic and chemical properties. The optical properties were investigated by determining the particle complex refractive index (CRI). The hygroscopicity was quantified by measuring the effect of relative humidity (RH) on the particle size (size growth factor, GF) and on the scattering coefficient (scattering growth factor, f(RH)). The oxygen to carbon atomic ratios (O : C) of the particle surface and bulk were used as a sensitive parameter to correlate the changes in hygroscopic and optical properties of the SOA composition during their formation and aging in CESAM.
The real CRI at 525 nm wavelength decreased from 1.43–1.60 (±0.02) to 1.32–1.38 (±0.02) during the SOA formation. The decrease in the real CRI correlated to the O : C decrease from 0.68 (±0.20) to 0.55 (±0.16). In contrast, the GF remained roughly constant over the reaction time, with values of 1.02–1.07 (±0.02) at 90% (±4.2%) RH. Simultaneous measurements of O : C of the particle surface revealed that the SOA was not composed of a homogeneous mixture, but contained less oxidised species at the surface which may limit water absorption. In addition, an apparent change in both mobility diameter and scattering coefficient with increasing RH from 0 to 30% was observed for SOA after 14 h of reaction. We postulate that this change could be due to a change in the viscosity of the SOA from a predominantly glassy state to a predominantly liquid state
Continuum viscoplastic simulation of a granular column collapse on large slopes: ÎĽ(I) rheology and lateral wall effects
We simulate here dry granular flows resulting from the collapse of granular columns on an inclined channel (up to 22°) and compare precisely the results with laboratory experiments. Incompressibility is assumed despite the dilatancy observed in the experiments (up to 10%). The 2-D model is based on the so-called μ(I) rheology that induces a Drucker-Prager yield stress and a variable viscosity. A nonlinear Coulomb friction term, representing the friction on the lateral walls of the channel, is added to the model. We demonstrate that this term is crucial to accurately reproduce granular collapses on slopes ≳10°, whereas it remains of little effect on the horizontal slope. Quantitative comparison between the experimental and numerical changes with time of the thickness profiles and front velocity makes it possible to strongly constrain the rheology. In particular, we show that the use of a variable or a constant viscosity does not change significantly the results provided that these viscosities are of the same order. However, only a fine tuning of the constant viscosity (η=1 Pa s) makes it possible to predict the slow propagation phase observed experimentally at large slopes. Finally, we observed that small-scale instabilities develop when refining the mesh (also called ill-posed behavior, characterized in the work of Barker et al. [“Well-posed and ill-posed behaviour of the μ(I)-rheology for granular flow,” J. Fluid Mech. 779, 794–818 (2015)] and in the present work) associated with the mechanical model. The velocity field becomes stratified and the bands of high velocity gradient appear. These model instabilities are not avoided by using variable viscosity models such as the μ(I) rheology. However we show that the velocity range, the static-flowing transition, and the thickness profiles are almost not affected by them
Latitudinal distribution of the solar wind properties in the low- and high-pressure regimes: Wind observations
- …