23 research outputs found
Heteroepitaxial hematite photoanodes as a model system for solar water splitting
Heteroepitaxial multilayer Pt(111)/Fe2O3(0001) films were deposited on sapphire c-plane (0001) substrates by RF magnetron sputtering and pulsed laser deposition, respectively. The films were highly crystalline, displaying an in-plane mosaic spread of less than 1° and a homogenous surface morphology with roughness of ∼3 Å. Ellipsometry and UV-vis spectroscopy measurements were shown to be in excellent agreement with modelling, demonstrating that the optics of the system including absorption in the hematite layer are well described. For polycrystalline hematite photoanodes deposited on platinum, full characterization of the system is hampered by the inability to make measurements in alkaline electrolyte containing hydrogen peroxide (H2O2) due to spontaneous decomposition of H2O2 by the exposed platinum. The pin-hole free high quality of the heteroepitaxial films is demonstrated by the ability to make stable and reproducible measurements in H2O2 containing electrolyte allowing for accurate extraction of charge separation and injection efficiency. The combination of excellent crystalline quality in addition to the well characterized optics and electrochemical properties of the heteroepitaxial hematite photoanodes demonstrate that Al2O3(0001)/Pt(111)/Fe2O3(0001) is a powerful model system for systematic investigation into solar water splitting photoanodes
Defect segregation and its effect on the photoelectrochemical properties of Ti-doped hematite photoanodes for solar water splitting
Optimising the photoelectrochemical performance of hematite photoanodes for
solar water splitting requires better understanding of the relationships
between dopant distribution, structural defects and photoelectrochemical
properties. Here, we use complementary characterisation techniques including
electron microscopy, conductive atomic force microscopy (CAFM), Rutherford
backscattering spectroscopy (RBS), atom probe tomography (APT) and intensity
modulated photocurrent spectroscopy (IMPS) to study this correlation in
Ti-doped (1 cat.%) hematite films deposited by pulsed laser deposition (PLD) on
F:SnO2 (FTO) coated glass substrates. The deposition was carried out at 300
{\deg}C, followed by annealing at 500 deg C for 2 h. Upon annealing, Ti was
observed by APT to segregate to the hematite/FTO interface and into some
hematite grains. Since no other pronounced changes in microstructure and
chemical composition were observed by electron microscopy and RBS after
annealing, the non-uniform Ti redistribution seems to be the reason for a
reduced interfacial recombination in the annealed films, as observed by IMPS.
This results in a lower onset potential, higher photocurrent and larger fill
factor with respect to the as-deposited state. This work provides atomic-scale
insights into the microscopic inhomogeneity in Ti-doped hematite thin films and
the role of defect segregation in their electrical and photoelectrochemical
properties
High quality oxide-free metallic nanoparticles: a strategy for synthesis through laser ablation in aqueous medium
The paper explores the synthesis of oxide-free nanoparticles of Ag and Cu through laser ablation of pure targets under aqueous medium and tuning the quality and size through addition of Polyvinylpyrrolidone (PVP) in the medium. The size distribution of nanoparticles reduces from 37 +/- 30 nm and 13 +/- 5 nm to 32 +/- 12 nm and 4 +/- 1 nm for Ag and Cu with changes in PVP concentration from 0.00 to 0.02 M, respectively. Irregular shaped particles of Ag with Ag2O phase and a Cu-Cu2O core-shell particles form without the addition of PVP, while oxide layer is absent with 0.02 M of PVP. The recent understanding of the mechanism of particle formation during laser ablation under liquid medium allows us to rationalize our observation
Synthesis and Mechanism of Composition and Size Dependent Morphology Selection in Nanoparticles of Ag-Cu Alloys Processed by Laser Ablation Under Liquid Medium
We have synthesized Ag-Cu alloy nanoparticles of four different compositions by using the laser ablation technique with the target under aqueous medium. Following this, we report a morphological transition in the nanoparticles from a normal two-phase microstructure to a structure with random segregation and finally a core shell structure at small sizes as a function of Cu concentration. To illustrate the composition dependence of morphology, we report observations carried out on nanoparticles of two different sizes: similar to 5 and similar to 20 nm. The results could be rationalized through the thermodynamic modeling of free energy of phase mixing and wettability of the alloying phases
Phase formation and stability of alloy phases in free nanoparticles: some insights
This paper explores phase formation and phase stability in free nanoparticles of binary alloys. A procedure for estimating the size and composition dependent free energies incorporating the contributions from the interfaces has been presented. Both single phase solid solution and two phase morphology containing interphase interfaces have been considered. A free energy scenario has been evaluated for two binary alloy systems Ag-Ni and Ag-Cu to predict the microstructure of the alloy nanoparticles at different size ranges as a function of composition. Both Ag-Cu and Ag-Ni systems exhibit wide bulk immiscibility. Ag-Ni nanoparticles were synthesized using the wet chemical synthesis technique whereas Ag-Cu nanoparticles were synthesized using laser ablation of a Ag-Cu target immersed in distilled water. Microstructural and compositional characterization of Ag-Ni and Ag-Cu nanoparticles on a single nanoparticle level was conducted using transmission electron microscopy. Nanoparticle microstructures observed from the microscopic investigation have been correlated with thermodynamic calculation results. It is shown that the observed two phase microstructure consisting of Ag-Ni solid solution in partial decomposed state coexisting with pure Ag phases in the case of Ag-Ni nanoparticles can be only be rationalized by invoking the tendency for phase separation of an initial solid solution with increase in nanoparticle size. Smaller sized Ag-Ni nanoparticles prefer a single phase solid solution microstructure. Due to an increase in particle size during the synthesis process the initial solid solution decomposes into an ultrafine scale phase separated microstructure. We have shown that it is necessary to invoke critical point phenomenon and wetting transition in systems showing a critical point that leads to phase separated Ag-Ni nanoparticles providing a catalytic substrate for the nucleation of equilibrium Ag over it. In the case of the Ag-Cu system, we report the experimental observation of a core shell structure at small sizes. This can be rationalized in terms of a metastable solid solution. It is argued that the nucleation barrier can prevent the formation of biphasic morphology with an internal interface. In such a situation, demixing of the solid solution can bring the system to a lower energy configuration. This has lead to the observed core-shell morphology in the Ag-Cu system during room temperature synthesis
Temperature- and Size-Dependent Compositionally Tuned Microstructural Landscape for Ag-46 Atom % Cu Nanoalloy Prepared by Laser Ablation in Liquid
We
report a temperature- and size-dependent compositionally tuned
microstructural landscape for Ag-46 atom % Cu alloy nanoparticles.
The microstructural and morphological changes were established through
the technique of in situ transmission electron microscopy. The nanoparticles
were synthesized by laser ablation of alloy target in an aqueous medium.
The as-synthesized particles predominantly contain nanosized grains
of a single-phase solid solution with grains having sizes ∼3
± 0.5 nm. For particles with smaller sizes (∼20 nm), the
solid solution decomposes and grains coarsen on heating to yield predominantly
bicrystals containing two phases of Ag-rich and Cu-rich solid solution.
The microstructure of the larger particles (≥40 nm) evolves
through segregation of Ag and their preferential growth near the surface
of the particles. This leads to a core–shell-like composition
distribution at a certain range of temperatures (≥200 °C)
and sizes (≥32 nm). At higher temperatures, these core–shell
particles undergo a morphological transition through grain growth
yielding bicrystals of two phases. We present a size- and temperature-dependent
morphology diagram that captures these changes
Synthesis and Mechanism of Composition and Size Dependent Morphology Selection in Nanoparticles of Ag–Cu Alloys Processed by Laser Ablation Under Liquid Medium
We
have synthesized Ag–Cu alloy nanoparticles of four different
compositions by using the laser ablation technique with the target
under aqueous medium. Following this, we report a morphological transition
in the nanoparticles from a normal two-phase microstructure to a structure
with random segregation and finally a core–shell structure
at small sizes as a function of Cu concentration. To illustrate the
composition dependence of morphology, we report observations carried
out on nanoparticles of two different sizes: ∼5 and ∼20
nm. The results could be rationalized through the thermodynamic modeling
of free energy of phase mixing and wettability of the alloying phases