The Influence of the effect of solute on the thermodynamic driving force on grain refinement of Al alloys

Grain refinement is known to be strongly affected by the solute in cast alloys. Addition of some solute can reduce grain size considerably while others have a limited effect. This is usually attributed to the constitutional supercooling which is quantified by the growth restriction factor, Q. However, one factor that has not been considered is whether different solutes have differing effects on the thermodynamic driving force for solidification. This paper reveals that addition of solute reduces the driving force for solidification for a given undercooling, and that for a particular Q value, it is reduced more substantially when adding eutectic-forming solutes than peritectic-forming elements. Therefore, compared with the eutectic-forming solutes, addition of peritectic-forming solutes into Al alloys not only possesses a higher initial nucleation rate resulted from the larger thermodynamic driving force for solidification, but also promotes nucleation within the constitutionally supercooled zone during growth. As subsequent nucleation can occur at smaller constitutional supercoolings for peritectic-forming elements, a smaller grain size is thus produced. The very small constitutional supercooling required to trigger subsequent nucleation in alloys containing Ti is considered as a major contributor to its extraordinary grain refining efficiency in cast Al alloys even without the deliberate addition of inoculants.The Australian Research Council (ARC DP10955737)

Microstructure and Porosity of Laser Welds in Cast Ti-6Al-4V with Addition of Boron

Addition of small amounts of boron to cast Ti-6Al-4V alloy has shown to render a finer microstructure and improved mechanical properties. For such an improved alloy to be widely applicable for large aerospace structural components, successful welding of such castings is essential. In the present work, the microstructure and porosity of laser welds in a standard grade cast Ti-6Al-4V alloy as well as two modified alloy versions with different boron concentrations have been investigated. Prior-β grain reconstruction revealed the prior-β grain structure in the weld zones. In fusion zones of the welds, boron was found to refine the grain size significantly and rendered narrow elongated grains. TiB particles in the prior-β grain boundaries in the cast base material restricted grain growth in the heat-affected zone. The TiB particles that existed in the as cast alloys decreased in size in the fusion zones of welds. The hardness in the weld zones was higher than in the base material and boron did not have a significant effect on hardness of the weld zones. The fusion zones were smaller in the boron-modified alloys as compared with Ti-6Al-4V without boron. Computed tomography X-ray investigations of the laser welds showed that pores in the FZ of the boron modified alloys were confined to the lower part of the welds, suggesting that boron addition influences melt pool flow

Modeling of Ti-W Solidification Microstructures Under Additive Manufacturing Conditions

Additive manufacturing (AM) processes have many benefits for the fabrication of alloy parts, including the potential for greater microstructural control and targeted properties than traditional metallurgy processes. To accelerate utilization of this process to produce such parts, an effective computational modeling approach to identify the relationships between material and process parameters, microstructure, and part properties is essential. Development of such a model requires accounting for the many factors in play during this process, including laser absorption, material addition and melting, fluid flow, various modes of heat transport, and solidification. In this paper, we start with a more modest goal, to create a multiscale model for a specific AM process, Laser Engineered Net Shaping (LENS™), which couples a continuum-level description of a simplified beam melting problem (coupling heat absorption, heat transport, and fluid flow) with a Lattice Boltzmann-cellular automata (LB-CA) microscale model of combined fluid flow, solute transport, and solidification. We apply this model to a binary Ti-5.5 wt pct W alloy and compare calculated quantities, such as dendrite arm spacing, with experimental results reported in a companion paper

Titanium sponge as a source of native nuclei in titanium alloys

Equiaxed β-grain morphologies have been observed in a wide array of Ti alloys produced by numerous solidification-based processes and, in terms of conventional solidification theory, are believed to be a consequence of heterogeneous nucleation upon native nucleant particles during solidification. In contrast, the source of these heterogeneous nuclei has yet to be established or explored in detail. In this work, titanium sponge was investigated as a possible common-denominator source of these nuclei. It was found that the native nuclei populations in titanium alloys may consist of transient interstitial-based compounds and fragments of titanium. A residual contaminant identified on the commercial titanium sponge pieces (sodium chloride), was also found to be effective at promoting smaller as-cast prior-β grain sizes

Investigating the morphological effects of solute on the β-phase in as-cast titanium alloys

An outstanding challenge in titanium solidification processes is controlling the primary β-phase morphology. Consequently, this paper investigates the efficacy of chromium additions to reduce anisotropic growth morphologies of the primary β-phase in titanium castings. By characterising the size, morphology and positions of β-grains in the cross-sections of each alloy, it is determined that, in contrast to established theory, chromium-containing castings yielded increased β-grain anisotropy, both in terms of size and morphology. It is proposed that these experimental results may still be consistent with established theory if certain theoretical assumptions are reconsidered