Analytical and experimental study of two concentric cylinders coupled by a fluid gap

From a structural point of view a liquid coolant type nuclear reactor consists of a heavy steel vessel containing the core and related mechanical components and filled with a hot fluid. This vessel is protected from the severe environment of the core by a shielding structure, the thermal liner, which is usually a relatively thin steel cylinder concentric with the reactor vessel and separated from it by a gap filled with the coolant fluid. This arrangement leads to a potential vibration problem if the fundamental frequency, or one of the higher natural vibration frequencies, of this liner system is close to the frequency of some vibration source present in the reactor vessel. The shell rigidly clamped at its base and free at the top was investigated since it is a better description of the conditions encountered in typical reactor designs

Design guide for single circular cylinder in turbulent crossflow. [LMFBR]

A design procedure is proposed for predicting the dynamic structural response of a circular cylinder in turbulent crossflow. The procedure is based on recently obtained data for a stationary, rigid cylinder and on existing information. The procedure is not applicable to conditions where the wake vortex shedding frequency locks into a structural natural frequency. This report is self-contained in that all the information and structural analysis methods employed in the procedure are reviewed and developed. Also, an example is given to illustrate the use of the method for a typical reactor component. The calculated responses are found to be very small

Leakage-flow-induced vibration of a tube-in-tube slip joint

The susceptibility of a cantilevered tube conveying water to self-excitation by leakage flow through a slip joint is assessed experimentally. The slip joint is formed by inserting a smaller, rigid tube into the free end of the cantilevered tube. Variations of the slip joint annular gaps and engagement lengths are tested, and several mechanisms for self-excitation are described

Tube crossflow force measurements

A transducer has been designed and verified which has the potential for measuring lift and drag forces on circular rods in turbulent cross flow. The transducer is currently being used to obtain data

Leakage flow-induced vibrations for variations of a tube-in-tube slip joint

Variations in the design of a specific slip joint separating two cantilevered, telescoping tubes conveying water were studied to determine their effect upon the leakage flow-induced vibration self-excitation mechanism known to exist for the original slip joint geometry. The important parameters controlling the self-excitation mechanism were identified, which, along with previous results, allowed the determination of a comprehensive set of design rules to avoid unstable vibrations. This was possible even though a new self-excitation mechanism was found when the engagement of the two tubes was small. 9 refs

Review of leakage-flow-induced vibrations of reactor components. [LMFBR]

The primary-coolant flow paths of a reactor system are usually subject to close scrutiny in a design review to identify potential flow-induced vibration sources. However, secondary-flow paths through narrow gaps in component supports, which parallel the primary-flow path, occasionally are the excitation source for significant vibrations even though the secondary-flow rates are orders of magnitude smaller than the primary-flow rate. These so-called leakage flow problems are reviewed here to identify design features and excitation sources that should be avoided. Also, design rules of thumb are formulated that can be employed to guide a design, but quantitative prediction of component response is found to require scale-model testing

Avoiding leakage flow-induced vibration by a tube-in-tube slip joint

Parameters and operating conditions (a stability map) were determined for which a specific slip-joint design did not cause self-excited lateral vibration of the two cantilevered, telescoping tubes forming the joint. The joint design featured a localized annular constriction. Flowrate, modal damping, tube engagement length, and eccentric positioning were among the parameters tested. Interestingly, all self-excited vibrations could be avoided by following a simple design rule: place constrictions only at the downstream end of the annular region between the tubes. Also, overall modal damping decreased with increased flowrate, at least initially, for upstream constrictions while the damping increased for downstream constrictions

Nitrosourea-misonidazole combination chemotherapy: effect on KHT sarcomas, marrow stem cells and gut.

C3H/HeJ mice bearing i.m. transplanted KHT sarcomas were treated with varying doses of either 1,3-bis(2-chloroethyl)-1-nitrosourea (BCNU) or 2-[3-(2-chloroethyl)-3-nitrosoureido]-D-glucopyranose (chlorozotocin; CHLZ) as single agents or in combination with 1 mg/g of the chemical radiosensitizer, misonidazole (MISO). Using an in vivo-in vitro tumour-excision assay, the administration of MISO simultaneously with or 3 h after low doses of BCNU (less than 20 mg/kg) was found to give a dose-modification factor (DMF) of approximately 1.65 relative to BCNU alone. At higher doses of BCNU, there was less enhancement of cell kill. The DMF for tumour growth delay was likewise dependent on BCNU dose, continuously decreasing with increasing BCNU dose. In contrast, the anti-tumour activity of CHLZ, assessed by both clonogenic cell survival and tumour-growth delay, was not significantly enhanced by the addition of MISO. The enhancement of gastrointestinal toxicity and haematotoxicity by BCNU-MISO combinations was assessed by LD50/7 and CFU-S assays, respectively. MISO enhanced BCNU marrow toxicity by a factor of 1.2-1.3, whilst gut toxicity was enhanced by a factor of approximately 1.2