134 research outputs found
Development and application of test cases for comparing vertical ground heat exchanger models
The main objective of this paper is to establish a set of test cases for analytical verifications and intermodel comparisons of ground heat exchanger (GHX) models used in building simulation programs. Several test cases are suggested. They range from steady-state heat rejection in a single borehole to varying hourly loads with large yearly thermal imbalance in multiple borehole configurations. The usefulness of the proposed test cases is illustrated by running them with different GHX models. This comparison exercise has shown that 1-D models compare favourably well with the more elaborate 3-D models for relatively small simulation periods. The cyclic heat rejection/collection test has revealed some small deficiency in the load aggregation scheme of a particular model. Finally, the use of the asymmetric (cooling-dominated) load profile test case for a bore field composed of 100 boreholes revealed that the borehole wall temperature predicted by two GHX models can differ by as much as 10oC after a 30 year simulation
Transient thermal analysis of a data centre cooling system under fault conditions
Data centres housing the IT infrastructure of large organisations constitute a considerable technical challenge to ensure 100% operational availability for mission critical IT systems. Specifying plant cooling systems to maintain suitable temperature levels and dissipate the heat generated can be carried out using industry standard design methods. However, accounting for perturbations in cooling due to failure of plant and restart of backup systems requires for faster thermal transients to be addressed than would normally be encountered in building system analysis. It is in this context that this paper describes the modelling and analysis of a 5 MW chilled water cooling system used for the cooling of a recently constructed UK data centre. The model has been developed using the TRNSYS software and includes a full model of the energy transfers for the data centre including chillers, hydraulic network, valve models and each of the 70 Room Air Conditioning Units. The coupling between the data centre air temperature levels and the cooler system has enabled a full assessment of the cooling system design in response to system perturbations. A number of scenarios are examined involving the failure of the chillers and how the inherent thermal inertia of the system plus additional inertia achieved through buffer vessels allowed a suitable design to be achieved. The detailed transient analysis model allowed the sizing of these vessels effectively and to gain a better understanding of the chilled water plant operation, both in normal conditions and in the case of failure
A comparison of the UK Standard Assessment Procedure and detailed simulation of solar energy systems for dwellings
The drive to reduce worldwide Carbon Emissions directly associated with dwellings and to achieve a zero carbon home dictates that Renewable Energy Technologies will have an increasingly large role in the built environment. Created by the Building Research Establishment (BRE), the Standard Assessment Procedure (SAP) is the UK Government's approved methodology for assessing the energy ratings of dwellings. This paper presents an evaluation of the advantage given to SAP ratings by the domestic installation of typical Photovoltaic (PV) and Solar Domestic Hot Water (SDHW) systems in the UK. Comparable PV and SDHW systems will also be simulated with more detailed modelling packages. Results suggest that calculation variances can exist between the SAP methodology and detailed simulation methods, especially for higher performance systems that deviate from the default efficiency parameters
Regional-scale inventory of periglacial moving landforms connected to the torrential network system
When connected to torrential channels, periglacial moving landforms (including
rock glaciers, push moraines and high-altitude landsliding masses) may
constitute important active sediment sources for gravitational and torrential
transfer processes such as debris flows. However, still very little is known
about the location and the number of such types of sedimentary connection in
given regions, as well as about the typical sediment transfer rates that can
be expected. Therefore, this contribution aims at (i) describing a new
methodology developed to identify and characterize moving landforms connected
to the torrential network system at a regional scale and (ii) presenting the
results yielded from the application of this method in a 2000 km2 region
in the southwestern Swiss Alps. The developed approach is based on the
analysis of simple data such as a high-resolution digital elevation model (DEM),
time series of aerial images and a slope movement inventory. The approach
allowed both the fast identification of moving landforms connected to
torrential channels and the estimation of annual sediment transfer rates for
these inventoried landforms. In the study region, results showed that such
types of sedimentary connection appeared to be rather rare. Results also showed that most connected moving landforms were characterized by relatively low
sediment transfer rates (<500 m3 yr−1) but several sites were
identified as transferring large amounts of sediment into the torrents
(>1000 m3 yr−1). As sediment transfer rates depend on the
kinematical behavior of the landforms, values calculated may change in regard
to the evolution of the surface velocities, which are currently generally
increasing in the European Alps. When connected to torrents, periglacial
moving landforms may thus represent substantial active sources of sediments
for the development of debris flows and should be considered in the
management of torrential catchments.</p
Motivational Effects of Acknowledging Feedback from a Socially Assistive Robot
Schneider S, Kummert F. Motivational Effects of Acknowledging Feedback from a Socially Assistive Robot. In: Agah A, Cabibihan J-J, Howard AM, Salichs MA, He H, eds. Social Robotics. ICSR 2016. Proceedings of the Eighth International Conference on Social Robotics. Lecture Notes in Computer Science. Vol 9979. Cham: Springer; 2016: 870-879
Molecular features of new Peach Latent Mosaic Viroid variants suggest that recombination may have contributed to the evolution of this infectious RNA.
peer reviewe
An incremental approach to automated protein localisation
Tscherepanow M, Jensen N, Kummert F. An incremental approach to automated protein localisation. BMC Bioinformatics. 2008;9(1): 445.Background:
The subcellular localisation of proteins in intact living cells is an important means for gaining information about protein functions. Even dynamic processes can be captured, which can barely be predicted based on amino acid sequences. Besides increasing our knowledge about intracellular processes, this information facilitates the development of innovative therapies and new diagnostic methods. In order to perform such a localisation, the proteins under analysis are usually fused with a fluorescent protein. So, they can be observed by means of a fluorescence microscope and analysed. In recent years, several automated methods have been proposed for performing such analyses. Here, two different types of approaches can be distinguished: techniques which enable the recognition of a fixed set of protein locations and methods that identify new ones. To our knowledge, a combination of both approaches – i.e. a technique, which enables supervised learning using a known set of protein locations and is able to identify and incorporate new protein locations afterwards – has not been presented yet. Furthermore, associated problems, e.g. the recognition of cells to be analysed, have usually been neglected.
Results:
We introduce a novel approach to automated protein localisation in living cells. In contrast to well-known techniques, the protein localisation technique presented in this article aims at combining the two types of approaches described above: After an automatic identification of unknown protein locations, a potential user is enabled to incorporate them into the pre-trained system. An incremental neural network allows the classification of a fixed set of protein location as well as the detection, clustering and incorporation of additional patterns that occur during an experiment. Here, the proposed technique achieves promising results with respect to both tasks. In addition, the protein localisation procedure has been adapted to an existing cell recognition approach. Therefore, it is especially well-suited for high-throughput investigations where user interactions have to be avoided.
Conclusion:
We have shown that several aspects required for developing an automatic protein localisation technique – namely the recognition of cells, the classification of protein distribution patterns into a set of learnt protein locations, and the detection and learning of new locations – can be combined successfully. So, the proposed method constitutes a crucial step to render image-based protein localisation techniques amenable to large-scale experiments
Proportional plus integral control of ladder circuits modeled in the form of two-dimensional (2D) systems
- …