150 research outputs found
Steam cycle options for capture-ready power plants, retrofits and flexible operation with post-combustion CO2 capture
The energy penalty for postâcombustion carbon dioxide capture from fossilâfired power plants can
be greatly reduced â independently of the intrinsic heat of regeneration of the solvent used â by
effective thermodynamic integration with the power cycle. Yet expected changes in electricity
generation mix and the current immaturity of postâcombustion capture technology are likely to
make effective thermodynamic integration throughout the operating life of such plants a challenging
objective to achieve because of a requirement for extensive partâload operation and also for
matching to future technology improvements. Most previous published studies have, however,
focused on baseâload operation of the power cycle and the carbon dioxide capture plant and with
the assumption of a fixed technology.
For carbon dioxide captureâready plants the characteristics of the capture plant are also not known
when the plant is designed. The plant must operate initially without capture at a similar efficiency to
âstandardâ plants to be competitive. Captureâready plants then also need to be able to be retrofitted
with unknown improved solvents and to be capable of integration with a range of future solvents.
This study shows that future upgradability for postâcombustion capture systems can be facilitated by
appropriate steam turbine and steam cycle designs. In addition fossilâfired power plants with postcombustion
capture may need to be able to operate throughout their load range with the capture
unit byâpassed, or with intermediate solvent storage to avoid the additional emissions occurring
when the absorption column is byâpassed. Steam cycles with flexible steam turbines can be
adequately designed to accommodate for partâload operation with these novel operating conditions
and with rapid ramp rates.
Several approaches for effective captureâready pulverised coal and natural gas plants are also
described. These achieve identical performance before retrofit to a conventional plant with the
same steam conditions, but have the potential to perform well after capture retrofit with a wide
range of solvents, at the expense of only a small efficiency penalty compared to hypothetical plants
built with perfect foreknowledge of the solvent energy requirements. For existing plants that were
not made captureâready, and provided sufficient space is available and other physical limits are not
too constraining, ways to achieve effective thermodynamic integration are also discussed
Addressing Technology Uncertainties in Power Plants with Post-Combustion Capture
AbstractRisks associated with technology, market and regulatory uncertainties for First-Of-A-Kind fossil power generation with CCS can be mitigated through innovative engineering approaches that will allow solvent developments occurring during the early stage of the deployment of post-combustion CO2 capture to be subsequently incorporated into the next generation of CCS plants. Power plants capable of improving their economic performance will benefit financially from being able to upgrade their solvent technology. One of the most important requirements for upgradeability is for the base power plant to be able to operate with any level of steam extraction and also with any level of electricity output up to the maximum rating without capture. This requirement will also confer operational flexibility and so is likely to be implemented in practice on new plants or on any integrated CCS retrofit project
On the retrofitting and repowering of coal power plants with post-combustion carbon capture: An advanced integration option with a gas turbine windbox
Retrofitting a significant fraction of existing coal-fired power plants is likely to be an important part of a global rollout of carbon capture and storage. For plants suited for a retrofit, the energy penalty for post-combustion carbon capture can be minimised by effective integration of the capture system with the power cycle. Previous work on effective integration options has typically been focused on either steam extraction from the power cycle with a reduction of the site power output, or the supply of heat and electricity to the capture system via the combustion of natural gas, with little consideration for the associated carbon emissions.
This article proposes an advanced integration concept between the gas turbine, the existing coal plant and post-combustion capture processes with capture of carbon emissions from both fuels. The exhaust gas of the gas turbine enters the existing coal boiler via the windbox for sequential combustion to allow capture in a single dedicated capture plant, with a lower flow rate and a higher CO2 concentration of the resulting flue gas. With effective integration of the heat recovery steam generator with the boiler, the existing steam cycle and the carbon capture process, the reference subcritical unit used in this study can be repowered with an electricity output penalty of 295 kWh/tCO2 â 5% lower than a conventional steam extraction retrofit of the same unit â and marginal thermal efficiency of natural gas combustion of 50% LHV â 5% point higher than in a configuration where the gas turbine has a dedicated capture unit
Maintaining the Power Output of An Existing Coal Plant with the Addition of CO 2 Capture: Retrofits Options With Gas Turbine Combined Cycle Plants
AbstractIt is likely that a significant number of existing pulverised coal-fired power plants will be retrofitted with post-combustion capture as part of a global rollout of carbon capture and storage. Previous studies have demonstrated that the energy penalty for post-combustion carbon dioxide (CO2) capture can be greatly minimised by effective integration of the capture system with the power cycle. Nevertheless, the power output of the site is, in most cases, reduced and the volume of electricity sales would drop. For other plants, the existing steam cycle may not be able to be integrated effectively for steam extraction, or space and access around/to the steam cycle may be impossible. As an alternative to steam extraction, it is possible to retrofit existing coal plants with a gas turbine combined cycle plant (CCGT) to maintain, or even increase, the site power output. The gas turbine can be integrated to the existing coal plant in various ways to supply all the heat, or a fraction of the heat, and the power required for the capture systems. An important consideration is whether carbon emissions from both, the combined cycle and the retrofitted coal plant are captured, or from the latter only.This paper examines these different options for carbon capture retrofits to existing coal plant and presents a novel configuration with the sequential combustion of gas turbine flue gas in the existing coal boiler while capturing carbon emissions from the combustion of coal and natural gas
A remotely-operated facility for evaluation of post-combustion CO2 capture technologies on industrial sites
ACTTROM (Advanced Capture Testing in a Transportable Remotely-Operated Minilab) is a transportable test facility for bench-scale evaluation of postcombustion CO2 capture technologies using real industrial flue gases. It is designed to be remote-operable, requiring visits only once per month for maintenance and sample collection. ACTTROM is the first facility of its kind, owned and operated by academia for collaborative research in an industrial environment, and this has resulted in a number of unique developments to facilitate remote operation at an industrial host site. Specifically, it has been necessary to design the unit to automatically correct or mitigate the effects of fault conditions, and to be remotely-monitored via a user interface at 24 hour intervals
- âŠ