52 research outputs found
Alloying effects on the oxidation behaviour of shot-peened Co-Ni base Superalloys
The effect of shot-peening on the oxidation mechanism in Co-Ni alloys with different Co-Ni ratios and varying Cr and Al contents were investigated at 850 °C for 200 h. A characterization method using isotopic oxygen tracing combined with focused ion-beam secondary ion mass spectrometry (FIB-SIMS) was performed to study the oxidation mechanism in both conditions. Multi-layered oxides in both peened and un-peened conditions consisted of chromia-rich scale on the outermost surface and a protective alumina-rich layer as the internal scale. Internal oxidation to different depths occurred within the alloys with the formation of alumina particles within a γ\u27-depleted zone. The morphology of the sub-surface oxides differed between the two surface conditions examined. Oxidation performance was quantified by measuring cross-sectional damage depths of the outer scale (chromia) and the internal oxidation depth (oxide fingers and y’-depleted depth). Oxidizing environments can promote recrystallization in the near-surface of the shot-peened conditions. The sub-surface oxide penetration for the shot-peened condition occurs to a more uniform depth and is associated with the grain boundaries of small recrystallized grains. This work forms part of an ongoing investigation to determine the effects of shot-peening in this alloy system with the oxidation performance to equivalent polished material at 850 °C
Ordering and the micromechanics of Ti-7Al
The evolution of intergranular lattice strain in the α titanium alloy Ti–7Al wt% was characterised using in situ time-of-flight (TOF) neutron diffraction during room temperature tensile loading. Samples were aged to promote ordering and the formation of nanometre-scale α2 (Ti3Al). On ageing, at 550°C and 625°C, dislocations were observed to travel in pairs, and in planar arrays, which has been attributed to the presence of ordering. A slight change in c/a was observed, from 1.6949 to 1.6945, and a slight increase in the macroscopic modulus. However, no changes were observed in the residual lattice strains, which are the grain-orientation average elastic strains produced by plasticity. Therefore it is inferred that the changes in deformation mechanisms caused by ordering that result in an enhanced vulnerability to dwell fatigue affect primarily the extent of slip localisation. The overall strain distributions between grains in different orientations are not changed
Recommended from our members
Policy Entrepreneurship by International Bureaucracies: The Evolution of Public Information in UN Peacekeeping
The UN Secretariat’s role in the expansion of peacekeeping after the cold war is debated. Different theoretical accounts offer competing interpretations: principal–agent models and sociological institutionalism tend to emphasize the Secretariat’s risk-averse behaviour; organizational learning scholarship and international political sociology find evidence of the Secretariat’s activism; constructivism analyses instances of both. I argue that the UN Secretariat can be both enthusiastic and cautious about new tasks depending on the circumstances and the issue area. For example, UN officials have been the driving force behind the development of public information campaigns by peacekeeping missions aimed at the local population. During the cold war, it was not regarded as necessary for UN missions to communicate with the public in the area of operation: their interlocutors were parties to the conflict and the diplomatic community. With the deployment of the first multidimensional missions in the late 1980s and the early 1990s, UN staff realized the need to explain the organization’s role to the local population and provide information about UN-supported elections. In promoting this innovation, they played the role of policy entrepreneurs. The institutionalization of this innovation, however, was not an automatic process and required continuous advocacy by UN information staff
Protocol for the perfusion and angiography imaging sub-study of the Third International Stroke Trial (IST-3) of alteplase treatment within six-hours of acute ischemic stroke
RATIONALE: Intravenous thrombolysis with recombinant tissue Plasminogen Activator improves outcomes in patients treated early after stroke but at the risk of causing intracranial hemorrhage. Restricting recombinant tissue Plasminogen Activator use to patients with evidence of still salvageable tissue, or with definite arterial occlusion, might help reduce risk, increase benefit and identify patients for treatment at late time windows. AIMS: To determine if perfusion or angiographic imaging with computed tomography or magnetic resonance help identify patients who are more likely to benefit from recombinant tissue Plasminogen Activator in the context of a large multicenter randomized trial of recombinant tissue Plasminogen Activator given within six-hours of onset of acute ischemic stroke, the Third International Stroke Trial. DESIGN: Third International Stroke Trial is a prospective multicenter randomized controlled trial testing recombinant tissue Plasminogen Activator (0·9 mg/kg, maximum dose 90 mg) started up to six-hours after onset of acute ischemic stroke, in patients with no clear indication for or contraindication to recombinant tissue Plasminogen Activator. Brain imaging (computed tomography or magnetic resonance) was mandatory pre-randomization to exclude hemorrhage. Scans were read centrally, blinded to treatment and clinical information. In centers where perfusion and/or angiography imaging were used routinely in stroke, these images were also collected centrally, processed and assessed using validated visual scores and computational measures. STUDY OUTCOMES: The primary outcome in Third International Stroke Trial is alive and independent (Oxford Handicap Score 0-2) at 6 months; secondary outcomes are symptomatic and fatal intracranial hemorrhage, early and late death. The perfusion and angiography study additionally will examine interactions between recombinant tissue Plasminogen Activator and clinical outcomes, infarct growth and recanalization in the presence or absence of perfusion lesions and/or arterial occlusion at presentation. The study is registered ISRCTN25765518
Dislocation interactions in near-alpha Titanium alloy Ti6242Si under LCF
Dislocation interactions were investigated in near-alpha titanium alloy Ti6242Si after low cycle fatigue. Samples from the gauge section and the crack initiation site on the fracture surface were studied. Grain pairs with different crystallographic orientations were analysed from the gauge section to understand the dislocation interactions near the boundary. Deformation was primarily caused by planar slip, localized into slip bands in primary alpha (αp) grains. Direct slip transfer was observed within grains having similar orientations. In contrast, slip transfer resulted in a different kind of dislocation nucleation in the neighboring hard grain where there was misorientation between the grains, with the observation of cross-slip. Strain transfer was observed between highly misoriented grain pairs. Crack nucleation occurred on an αp grain by basal plane splitting, due to the large tensile stress developed by a double ended pile-up. This kind of pile-up is suggested to result from the incomplete reversibility of dislocation motion during load reversals. The observation of superjogs on the basal dislocations in the crack nucleated αp grain provides a rationale for why cracks nucleate near, rather than on, the basal plane
Embrittlement of alloy 625 and effect of remedial treatments
This study investigated the susceptibility of alloy 625 to embrittlement in the temperature range 600–800 ℃ using simulated thermal treatments, specimens from ex-service petroleum industry components and subsequent remedial heat treatment. Embrittlement was quantified by conducting impact testing using the Charpy V-notch method and the results discussed in terms of precipitate formation and ageing. The results of annealing the exposed samples at high temperature are presented, demonstrating that embrittlement is most detrimental at intermediate temperatures (i.e. 650 ℃). The study confirms that a 24-h remedial heat treatment of embrittled alloy 625 leads to significant recovery of impact energy on ex-service samples. </jats:p
A validated through process model to predict the fatigue life of a cast A356 automotive wheel
Through process modeling of aluminum alloy castings relating casting defects to fatigue performance
A validated model of the cyclic stress state of an A356 automotive wheel and its impact on fatigue life
- …