438 research outputs found
Analysis of potential helicopter vibration reduction concepts
Results of analytical investigations to develop, understand, and evaluate potential helicopter vibration reduction concepts are presented in the following areas: identification of the fundamental sources of vibratory loads, blade design for low vibration, application of design optimization techniques, active higher harmonic control, blade appended aeromechanical devices, and the prediction of vibratory airloads. Primary sources of vibration are identified for a selected four-bladed articulated rotor operating in high speed level flight. The application of analytical design procedures and optimization techniques are shown to have the potential for establishing reduced vibration blade designs through variations in blade mass and stiffness distributions, and chordwise center-of-gravity location
Predicting the required number of training samples
A criterion which measures the quality of the estimate of the covariance matrix of a multivariate normal distribution is developed. Based on this criterion, the necessary number of training samples is predicted. Experimental results which are used as a guide for determining the number of training samples are included
Multistage classification of multispectral Earth observational data: The design approach
An algorithm is proposed which predicts the optimal features at every node in a binary tree procedure. The algorithm estimates the probability of error by approximating the area under the likelihood ratio function for two classes and taking into account the number of training samples used in estimating each of these two classes. Some results on feature selection techniques, particularly in the presence of a very limited set of training samples, are presented. Results comparing probabilities of error predicted by the proposed algorithm as a function of dimensionality as compared to experimental observations are shown for aircraft and LANDSAT data. Results are obtained for both real and simulated data. Finally, two binary tree examples which use the algorithm are presented to illustrate the usefulness of the procedure
Processing techniques development, volume 2. Part 1: Crop inventory techniques
There are no author-identified significant results in this report
Processing techniques development, volume 3
The author has identified the following significant results. Analysis of the geometric characteristics of the aircraft synthetic aperture radar (SAR) relative to LANDSAT indicated that relatively low order polynominals would model the distortions to subpixel accuracy to bring SAR into registration for good quality imagery. Also the area analyzed was small, about 10 miles square, so this is an additional constraint. For the Air Force/ERIM data, none of the tested methods could achieve subpixel accuracy. Reasons for this is unknown; however, the noisy (high scintillation) nature of the data and attendent unrecognizability of features contribute to this error. It is concluded that the quadratic model would adequately provide distortion modeling for small areas, i.e., 10 to 20 miles square
Requirements of a global information system for corn production and distribution
There are no author-identified significant results in this report
Agricultural scene understanding
The author has identified the following significant results. The LACIE field measurement data were radiometrically calibrated. Calibration enabled valid comparisons of measurements from different dates, sensors, and/or locations. Thermal band canopy results included: (1) Wind velocity had a significant influence on the overhead radiance temperature and the effect was quantized. Biomass and soil temperatures, temperature gradient, and canopy geometry were altered. (2) Temperature gradient was a function of wind velocity. (3) Temperature gradient of the wheat canopy was relatively constant during the day. (4) The laser technique provided good quality geometric characterization
Probabilistic Relaxation on Multitype Data
Classification of multispectral image data based on spectral information has been a common practice in the analysis of remote sensing data. However, the results produced by current classification algorithms necessarily contain residual inaccuracies and class ambiguity. By the use of other available sources of information, such as spatial, temporal and ancillary information, it is possible to reduce this class ambiguity and in the process improve the accuracy.
In this paper, the probabilistic and supervised relaxation techniques are adapted to the problem. The common probabilistic relaxation labeling algorithm (PRL), which in remote sensing pixel labeling usually converges toward accuracy deterioration, is modified. Experimental results show that the modified relaxation algorithm reduces the labeling error in the first few iterations, then converges to the achieved minimum error. Also a noniterative labeling algorithm which has a performance similar to that of the modified PRL is developed. Experimental results from Landsat and Skylab data are included
Use of Unlabeled Samples for Mitigating the Hughes Phenomenon
The use of unlabeled samples in improving the performance of classifiers is studied. When the number of training samples is fixed and small, additional feature measurements may reduce the performance of a statistical classifier. It is shown that by using unlabeled samples, estimates of the parameters can be improved and therefore this phenomenon may be mitigated. Various methods for using unlabeled samples are reviewed and experimental results are provided
Assessment of methods of acquiring analyzing, and reporting crop production statistics, volume 4
There are no author-identified significant results in this report
- …