INVESTIGATION OF TECHNIQUES FOR REDUCING UNINTENTIONAL ELECTROMAGNETIC EMISSIONS FROM ELECTRONIC CIRCUITS AND SYSTEMS

This dissertation describes three independent studies related to techniques for reducing unintentional electromagnetic emissions from electronic circuits and systems. The topics covered are: low-inductance multi-layer ceramic capacitor for high frequency circuit board decoupling, the application of imbalance difference model to various circuit board and cable geometries, and balanced cable interface for reducing common-mode currents from power inverter. The first chapter discusses the importance and the meaning of the connection inductance associated with MLCCs and analyzes the effect of plate orientation in MLCCs. It demonstrates that vertically oriented plates have no more or less inductance than horizontally oriented plates when the overall dimensions of the plate stack are similar. Decoupling capacitance options at the various levels of a high-speed circuit is investigated to determine the range of frequencies that decoupling at each level is likely to be is effective. Innovative low-inductance capacitive-stem capacitor configurations are described and their connection impedance is compared to that of standard surface-mounted capacitors. The second chapter investigates the imbalance difference model that is a method for modeling how differential-mode signal currents are converted to common-mode noise currents. Various cable geometries to determine how well imbalance factor`s values of DM-to-CM conversion compare to full-wave calculations are explored. The imbalance difference model can be applied to cables with more than two conductors are demonstrated. The third chapter investigates the balanced cable interface for reducing common-mode currents from power inverter. The concept of a balancing network to reduce the common-mode currents on power inverter cables above 30 MHz is introduced. An experimental test set-up is used to demonstrate the effect of a balancing network on the common-mode current, differential-mode current and the common-mode rejection ratio on a balanced cable with an imbalanced termination. The balancing network is also evaluated using a 3-phase brushless DC motor driver to verify its effectiveness in a real application

Semiconductor integrated circuit chip, multilayer chip capacitor and semiconductor integrated circuit chip package

Disclosed are a semiconductor integrated circuit chip, a multilayer chip capacitor, and a semiconductor integrated circuit chip package. The semiconductor integrated circuit chip includes a semiconductor integrated circuit chip body, an input/output terminal disposed on the outside of the semiconductor integrated circuit chip body, and a decoupling capacitor disposed at a side face of the semiconductor integrated circuit chip body and electrically connected to the input/output terminal. The semiconductor integrated circuit chip cab be obtained, which can maintain an impedance of a power distribution network below a target impedance in a wide frequency range, particularly at a high frequency, by minimizing an inductance between a decoupling capacitor and a semiconductor integrated circuit chip

Nematic response revealed by coherent phonon oscillations in BaFe2_2As2_2

We investigate coherent phonon oscillations of BaFe$_2$As$_2$ using optical pump-probe spectroscopy. Time-resolved optical reflectivity shows periodic modulations due to $A_{1g}$ coherent phonon of $c$-axis arsenic vibrations. Optical probe beams polarized along the orthorhombic $a$- and $b$-axes reveal that the initial phase of coherent oscillations shows a systematic deviation as a function of temperature, although these oscillations arise from the same $c$-axis arsenic vibrations. The oscillation-phase remains anisotropic even in the tetragonal structure, reflecting a nematic response of BaFe$_2$As$_2$. Our study suggests that investigation on the phase of coherent phonon oscillations in optical reflectivity can offer unique evidence of a nematic order strongly coupled to a lattice instability.Comment: 5 pages, 4 figure

Integration between WSNs and Internet based on Address Internetworking for Web Services

There has been an increasing interest in wireless sensor networks as a new technology to realize ubiquitous computing, and demands for internetworking technology between the wireless sensor networks and the Internet which is based on IP address. For this purpose, this paper proposes and implements the internetworking scheme which assigns IP addresses to the sensor nodes and internetworks based on the gateway-based integration for internetworking between the wireless sensor networks and the Internet. That is, the proposed scheme makes the access to the wireless sensor networks be serviced as like the Web service with internetworking Internet IP address and ZigBee address which is allocated to the sensor node in wireless sensor networks. For validating the proposed scheme, we made experiments using Berkeley TinyOS, Mica Motes, dual protocol stack based on ZigBee and IP, and showed the service result using browser (IE) and IPv6 address based on DNS

Continuous Tip Widening Technique for Roll-to-Roll Fabrication of Dry Adhesives

In this study, we reported continuous partial curing and tip-shaped modification methods for continuous production of dry adhesive with microscale mushroom-shaped structures. Typical fabrication methods of dry adhesive with mushroom-shaped structures are less productive due to the failure of large tips on pillar during demolding. To solve this problem, a typical pillar structure was fabricated through partial curing, and tip widening was realized through applying the proper pressure. Polyurethane acrylate was used in making the mushroom structure using two-step UV-assisted capillary force lithography (CFL). To make the mushroom structure, partial curing was performed on the micropillar, followed by tip widening. Dry adhesives with properties similar to those of typical mushroom-shaped dry adhesives were fabricated with reasonable adhesion force using the two-step UV-assisted CFL. This production technology was applied to the roll-to-roll process to improve productivity, thereby realizing continuous production without any defects. Such a technology is expected to be applied to various fields by achieving the productivity improvement of dry adhesives, which is essential for various applications

Educational implications for university education through analysing learning outcomes, teaching-learning strategy and assessment strategy of universities of the United Kingdom- courses/programs related to life science

The purpose of this study is to analyse the specifications in the course/module descriptions in the field of biological science in UK universities and to examine its implications for the innovation of higher education. For supporting data, learning outcomes, teaching & learning strategies and assessment strategies in the course/module descriptions were closely analysed. In many UK universities, learning outcomes were presented according to four com-ponents of knowledge and understanding, cognitive (in-tellectual) skills, practical skills and transferable/key skills.In this research, total twelve teaching & learning strategies and thirteen assessment strategies were examined in the course/module descriptions related to life science of UK universities with TEF Gold. The mean number of teaching & learning strategies was 7.9. and as for the assessment strategies was 7.7. The results showed that UK universities use various teaching & learning and assessment strategies. Moreover, learning outcomes, teaching & learning and assess-ment strategies are consistently structured in the course/ programs in the field of biological sciences.The develop-ment of consistent and detailed specifications in the course/module descriptions such as learning outcomes, tea-ching & learning and assessment strategies would con-tribute to innovative higher education

CDMA2000 Downlink Performance Analysis Based on Deterministic Ray-Tracing Channel Model

This paper presents frame error rate (FER) properties of downlink in CDMA2000 system with the movement of the mobile terminal in high-rise urban environment. The site-specific channel model based on ray-tracing technique is chosen for this analysis with the established cells and sectors for the current IS-95 service. The tendency of FER according to the position of the mobile terminal is analyzed. From this analysis, we can infer the possibility of using the established IS-95 cell plannings for the CDMA2000 service