Influence of shock wave propagation on dielectric barrier discharge plasma actuator performance

Interest in plasma actuators as active flow control devices is growing rapidly due to their lack of mechanical parts, light weight and high response frequency. Although the flow induced by these actuators has received much attention, the effect that the external flow has on the performance of the actuator itself must also be considered, especially the influence of unsteady high-speed flows which are fast becoming a norm in the operating flight envelopes. The primary objective of this study is to examine the characteristics of a dielectric barrier discharge (DBD) plasma actuator when exposed to an unsteady flow generated by a shock tube. This type of flow, which is often used in different studies, contains a range of flow regimes from sudden pressure and density changes to relatively uniform high-speed flow regions. A small circular shock tube is employed along with the schlieren photography technique to visualize the flow. The voltage and current traces of the plasma actuator are monitored throughout, and using the well-established shock tube theory the change in the actuator characteristics are related to the physical processes which occur inside the shock tube. The results show that not only is the shear layer outside of the shock tube affected by the plasma but the passage of the shock front and high-speed flow behind it also greatly influences the properties of the plasma

Influence of composition and precipitation evolution on damage at grain boundaries in a crept polycrystalline Ni-based superalloy

© 2018 Acta Materialia Inc. The microstructural and compositional evolution of intergranular carbides and borides prior to and after creep deformation at 850 °C in a polycrystalline nickel-based superalloy was studied. Primary MC carbides, enveloped within intergranular γ′ layers, decomposed resulting in the formation of layers of the undesirable η phase. These layers have a composition corresponding to Ni3Ta as measured by atom probe tomography and their structure is consistent with the D024 hexagonal structure as revealed by transmission electron microscopy. Electron backscattered diffraction reveals that they assume various misorientations with regard to the adjacent grains. As a consequence, these layers act as brittle recrystallized zones and crack initiation sites. The composition of the MC carbides after creep was altered substantially, with the Ta content decreasing and the Hf and Zr contents increasing, suggesting a beneficial effect of Hf and Zr additions on the stability of MC carbides. By contrast, M5B3 borides were found to be microstructurally stable after creep and without substantial compositional changes. Borides at 850 °C were found to coarsen, resulting in some cases into γ′- depleted zones, where, however, no cracks were observed. The major consequences of secondary phases on the microstructural stability of superalloys during the design of new polycrystalline superalloys are discussed

Anodized aluminium pressure sensitive paint: effect of paint application technique

The porous surface of the Anodized Aluminium Pressure Sensitive Paint (AA-PSP) is what differentiates it from conventional sol–gel based PSPs, leading to a faster response time of the paint. The objective of the current study is to examine the effect of the paint application technique, i.e., whether the AA substrate is dipped or sprayed, on the pressure and temperature sensitivity. A more practical procedure for preparing the AA samples is also presented. Scanning Electron Microscope (SEM) images are acquired together with the calibration of the AA-PSP at various temperatures and pressures to determine the effectiveness of each application technique. The results revealed that the AA sample which was dipped in the PSP solution shows a higher pressure sensitivity than the sprayed one. The SEMs show that spraying leads to the covering up of the micropores created on the surface and undermining the benefit of anodization

Compressible flow structures interaction with a two-dimensional ejector: a cold-flow study

An experimental study has been conducted to examine the interaction of compressible flow structures such as shocks and vortices with a two-dimensional ejector geometry using a shock-tube facility. Three diaphragm pressure ratios ofP4 =P1 = 4, 8, and 12 have been employed, whereP4 is the driver gas pressure andP1 is the pressure within the driven compartment of the shock tube. These lead to incident shock Mach numbers of Ms = 1:34, 1.54, and 1.66, respectively. The length of the driver section of the shock tube was 700 mm. Air was used for both the driver and driven gases. High-speed shadowgraphy was employed to visualize the induced flowfield. Pressure measurements were taken at different locations along the test section to study theflow quantitatively. The induced flow is unsteady and dependent on the degree of compressibility of the initial shock wave generated by the rupture of the diaphragm

Revealing the true partitioning character of zirconium in additively manufactured polycrystalline superalloys

International audienc

Development of measurement-based load models for the dynamic simulation of distribution grids

The advent of new types of loads, such as power electronics and the increased penetration of low-inertia motors in the existing distribution grids alter the dynamic behavior of conventional power systems. Therefore, more accurate dynamic, aggregate, load models are required for the rigorous assessment of the stability limits of modern distribution networks. In this paper, a measurement-based, input/output, aggregate load model is proposed, suitable for dynamic simulations of distribution grids. The new model can simulate complex load dynamics by employing variable-order transfer functions. The minimum required model order is automatically determined through an iterative procedure. The applicability and accuracy of the proposed model are thoroughly evaluated under distinct loading conditions and network topologies using measurements acquired from a laboratory-scale test setup. Furthermore, the performance of the proposed model is compared against other conventional load models, using the mean absolute percentage error

Quantification challenges for atom probe tomography of hydrogen and deuterium in zircaloy-4

Analysis and understanding of the role of hydrogen in metals is a significant challenge for the future of materials science, and this is a clear objective of recent work in the atom probe tomography (APT) community. Isotopic marking by deuteration has often been proposed as the preferred route to enable quantification of hydrogen by APT. Zircaloy-4 was charged electrochemically with hydrogen and deuterium under the same conditions to form large hydrides and deuterides. Our results from a Zr hydride and a Zr deuteride highlight the challenges associated with accurate quantification of hydrogen and deuterium, in particular associated with the overlap of peaks at a low mass-to-charge ratio and of hydrogen/deuterium containing molecular ions. We discuss possible ways to ensure that appropriate information is extracted from APT analysis of hydrogen in zirconium alloy systems that are important for nuclear power applications

A three-level distributed architecture for the real-time monitoring of modern power systems

To monitor network operation in real-time, power system operators have developed wide-area monitoring systems (WAMS). However, the centralized communication and information processing architecture of WAMS cannot be extended easily to distribution networks. In this aspect, a three-level distributed network monitoring architecture is proposed in this paper, concerning the dynamic analysis of transmission, primary and secondary distribution networks by exploiting measurements of ambient data and transient responses. In the proposed architecture, operators are responsible for the operation and analysis of their own grid but also can share an overview of the system performance to facilitate their operational coordination. Different online and offline applications are supported within the architecture, including small-signal, transient and frequency stability analysis as well as dynamic equivalencing and real-time inertia estimation. Measurement-based algorithms and models are proposed for each case. Finally, the performance of the developed algorithms has been tested by using a combined transmission and distribution power system model

Methodology for evaluating equivalent models for the dynamic analysis of power systems

The increasing penetration of distributed renewable energy sources drastically alters the dynamic characteristics of distribution networks (DNs). Therefore, several equivalent models have been recently proposed, to analyze more accurately the complex behavior of modern DNs. However, relatively simple models are still commonly used in practice for dynamic power system studies. In addition, dynamic equivalent models for DNs are sensitive to different operating conditions and there is lack of systematic understanding of their performance. Scope of this paper is to propose a methodology for identifying the applicability range in terms of accuracy and generalization capability of several conventional and newly developed equivalent models for the dynamic analysis of modern DNs. A set of metrics is used for the modelling accuracy assessment and a sensitivity analysis framework is introduced to fully quantify the generalization capabilities of DN equivalent models. Based on the above, guidelines and recommendations for the development of robust equivalent models for DN analysis are proposed