84 research outputs found
Recommended from our members
Hollow square core fiber sensor for physical parameters measurement
The measurement of physical parameters is important in many current applications, since they often rely on these measurands to operate with the due quality and the necessary safety. In this work, a simple and robust optical fiber sensor based on an antiresonant hollow square core fiber (HSCF) is proposed to measure simultaneously temperature, strain, and curvature. The proposed sensor was designed in a transmission configuration where a segment of HSCF, with a 10 mm length, was spliced between two single mode fibers. In this sensor, a cladding modal interference (CMI) and a Mach-Zehnder interference (MZI) are enhanced along with the antiresonance (AR) guidance. All the present mechanisms exhibit different responses towards the physical parameters. For the temperature, sensitivities of 32.8 pm/°C, 18.9 pm/°C, and 15.7 pm/°C were respectively attained for the MZI, AR, and CMI. As for the strain, sensitivities of 0.45 pm/μϵ, -0.93 pm/μϵ, and -2.72 pm/μϵ were acquired for the MZI, AR and CMI respectively. Meanwhile, for the curvature measurements, two regions of analysis were considered. In the first region (0 m-1 - 0.7 m-1) sensitivities of 0.033 nm/m-1, -0.27 nm/m-1, and -2.21 nm/m-1 were achieved, whilst for the second region (0.7 m-1 - 1.5 m-1) sensitivities of 0.067 nm/m-1, -0.63 nm/m-1, and -0.49 nm/m-1 were acquired for the MZI, AR and CMI, respectively
Hybrid sensor based on a hollow square core fiber for temperature independent refractive index detection
In this work, a hybrid sensor based on a section of hollow square core fiber (HSCF) spliced between two single mode fibers is proposed for the measurement of refractive index of liquids. The sensor, with a length of a few millimeters, operates in a transmission configuration. Due to the HSCF inner geometry, two different interferometers are generated. The first, a Mach-Zehnder interferometer, is insensitive to the external refractive index, and presents a sensitivity to temperature of (29.2 ± 1.1) pm/°C. The second one, a cladding modal interferometer, is highly sensitive to the external refractive index. An experimental resolution of 1.0 × 10-4 was achieved for this component. Due to the different responses of each interferometer to the parameters under study, a compensation method was developed to attain refractive index measurements that are temperature independent. The proposed sensor can find applications in areas where refractive index measurements are required and the control of room temperature is a challenge, such as in the food and beverage industry, as well as in biochemical or biomedical industries.publishe
Recommended from our members
Capillary based hybrid fiber sensor in a balloon-like shape for simultaneous measurement of displacement and temperature
In this work, a hybrid sensor based on a silica capillary in a balloon-like shape for simultaneous measurement of displacement and temperature is proposed for the first time, to the best of our knowledge. The sensor is fabricated by splicing a segment of a hollow core fiber between two single mode fibers (SMF) and by bending the fiber in a balloon shape with the capillary at the top-center position. In a transmission scheme, the SMF-capillary-SMF configuration excites an antiresonant (AR) guidance and the balloon shape enhances a Mach-Zehnder interferometer (MZI). The different responses of the interferometers to external displacement and temperature variations are conducive to a hybrid application of the sensor for simultaneous measurement of these parameters. Experimental results show that, for a capillary length of 1.2 cm and a balloon length of 4 cm, AR is insensitive to displacement and its sensitivity to temperature is 14.3 pm/°C, while the MZI has a sensitivity to displacement of 1.68 nm/mm and twice the sensitivity of AR to temperature, of 28.6 pm/°C. The proposed fiber sensor consists of only one sensing element in one configuration exciting two interferometers at the same time, which makes it of simple fabrication as well as low cost
Negative curvature hollow core fiber sensor for the measurement of strain and temperature
Three different types of strain and temperature sensors based on negative curvature hollow core fiber (NCHCF) are proposed. Each sensor is produced by splicing a small section of the NCHCF between two sections of single mode fiber. Different types of interferometers are obtained simply by changing the splicing conditions. The first sensor consists on a single Fabry-Perot interferometer (FPI). The remaining two configurations are attained with the same sensing structure, depending on its position in relation to the interrogation setup. Thus, a double FPI or a hybrid sensor, the latter being composed by an FPI and a Michelson interferometer, are formed. The inline sensors are of submillimeter size, thus enabling nearly punctual measurements
Negative curvature hollow core fiber sensor for the measurement of strain and temperature
Three different types of strain and temperature sensors based on negative curvature hollow core fiber (NCHCF) are proposed. Each sensor is produced by splicing a small section of the NCHCF between two sections of single mode fiber. Different types of interferometers are obtained simply by changing the splicing conditions. The first sensor consists on a single Fabry-Perot interferometer (FPI). The remaining two configurations are attained with the same sensing structure, depending on its position in relation to the interrogation setup. Thus, a double FPI or a hybrid sensor, the latter being composed by an FPI and a Michelson interferometer, are formed. The inline sensors are of submillimeter size, thus enabling nearly punctual measurements.publishe
Simultaneous measurement of refractive index and temperature using a double antiresonant hollow core fiber
In this work, an inline sensor based on a double antiresonant hollow core fiber is proposed for the simultaneous
measurement of refractive index and temperature. The fiber, consisting of four silica capillaries with wall thickness of
~1.5 um and a cladding with a thickness of ~36.5 um, is spliced between two sections of single mode fiber. The spectral
behavior, measured in transmission, results from the combination of different frequencies which enable the
discrimination between the two parameters. The sensing head is subjected to refractive index measurements using
aqueous solutions with different concentrations of ethanol. For a sensor with a length of ~10 mm, and considering the
lower frequency signal, the sensitivity to refractive index is 389.6 nm/RIU, whereas for the higher frequency, the
sensitivity attained is 2.8 nm/RIU. On the other hand, the sensing head presented a sensitivity to temperature of
25.5 pm/K and -27.6 pm/K for the higher and lower frequencies, respectively.publishe
Recommended from our members
Hybrid soliton dynamics in liquid-core fibres
The discovery of optical solitons being understood as temporally and spectrally stationary optical states has enabled numerous innovations among which, most notably, supercontinuum light sources have become widely used in both fundamental and applied sciences. Here, we report on experimental evidence for dynamics of hybrid solitons—a new type of solitary wave, which emerges as a result of a strong non-instantaneous nonlinear response in CS2-filled liquid-core optical fibres. Octave-spanning supercontinua in the mid-infrared region are observed when pumping the hybrid waveguide with a 460 fs laser (1.95 μm) in the anomalous dispersion regime at nanojoule-level pulse energies. A detailed numerical analysis well correlated with the experiment uncovers clear indicators of emerging hybrid solitons, revealing their impact on the bandwidth, onset energy and noise characteristics of the supercontinua. Our study highlights liquid-core fibres as a promising platform for fundamental optics and applications towards novel coherent and reconfigurable light sources
Recommended from our members
Carbon chloride-core fibers for soliton mediated supercontinuum generation
We report on soliton-fission mediated infrared supercontinuum generation in liquid-core step-index fibers using highly transparent carbon chlorides (CCl4, C2Cl4). By developing models for the refractive index dispersions and nonlinear response functions, dispersion engineering and pumping with an ultrafast thulium fiber laser (300 fs) at 1.92 μm, distinct soliton fission and dispersive wave generation was observed, particularly in the case of tetrachloroethylene (C2Cl4). The measured results match simulations of both the generalized and a hybrid nonlinear Schrödinger equation, with the latter resembling the characteristics of non-instantaneous medium via a static potential term and representing a simulation tool with substantially reduced complexity. We show that C2Cl4 has the potential for observing non-instantaneous soliton dynamics along meters of liquid-core fiber opening a feasible route for directly observing hybrid soliton dynamics
Recommended from our members
Three-dimensional spatiotemporal tracking of nano-objects diffusing in water-filled optofluidic microstructured fiber
Three-dimensional (3D) tracking of nano-objects represents a novel pathway for understanding dynamic nanoscale processes within bioanalytics and life science. Here we demonstrate 3D tracking of diffusing 100 nm gold nanosphere within a water-filled optofluidic fiber via elastic light scattering-based position retrieval. Specifically, the correlation between intensity and position inside a region of a fiber-integrated microchannel has been used to decode the axial position from the scattered intensity, while image processing-based tracking was used in the image plane. The 3D trajectory of a diffusing gold nanosphere has been experimentally determined, while the determined diameter analysis matches expectations. Beside key advantages such as homogenous light-line illumination, low-background scattering, long observation time, large number of frames, high temporal and spatial resolution and compatibility with standard microscope, the particular properties of operating with water defines a new bioanalytical platform that is highly relevant for medical and life science applications. © 2020 Shiqi Jiang et al., published by De Gruyter. 2020
High-power fiber laser based on a non filamented-core fully-aperiodic large pitch fiber
International audienceSince the double-clad fiber architectures development, fiber-based laser have witnessed an impressive power scaling [1]. The extracted power rising has been accompanied by the development of Very Large Mode Area (VLMA) fiber designs allowing overcome some key hurdles like the non-linear process or photo-darkening [2]. However, due to the very large core size of fiber architectures, a new phenomenon, referring to modal instabilities, has been evidenced recently like the current limitation which hampers any further power increase in the field of fiber laser sources without a dramatic degradation of the emitted beam quality [3]. In order to push away the appearance power threshold of this limitation, new aperiodic cladding microstructurations have been proposed to improve the higher-order modes (HOM) rejection out of the gain region and then to optimize the amplification of the sole fundamental mode [4]. These aperiodic microstructures have proved recently their potential to enhance an efficient HOM delocalization enabling singlemode confinement in the core region with passive VLMA fibers [5].In this communication we report on the first high power emission demonstration obtained using a solid non-filamented core fully-aperiodic large pitch fiber manufactured by the REPUSIL method based on the sintering and vitrification of micrometric doped silica powders. Using a simple laser cavity, an average output power of 233 W was achieved with an available pump power of 400 W for the first time in such a fiber. The preliminary M2 measurements have shown an excellent beam quality with values less than 1.4
- …