12,968 research outputs found
Coherent structures and modeling: Some background comments
Coherent structures are discussed as a sequence of events (identifiable motions) in the flow which convert significant amounts of mechanical energies of the mean flow stream, into turbulent fluctuations. The use of structure information in modeling is also discussed
Phase-lock loop frequency control and the dropout problem
Technique automatically sets the frequency of narrow band phase-lock loops within automatic lock-in-range. It presets a phase-lock loop to a desired center frequency with a closed loop electronic frequency discriminator and holds the phase-lock loop to that center frequency until lock is achieved
A review of quasi-coherent structures in a numerically simulated turbulent boundary layer
Preliminary results of a comprehensive study of the structural aspects of a numerically simulated number turbulent boundary layer are presented. A direct Navier-Stokes simulation of a flat-plate, zero pressure gradient boundary layer at Re0 = 670 was used. Most of the known nonrandom, coherent features of turbulent boundary layers are confirmed in the simulation, and several new aspects of their spatial character are reported. The spatial relationships between many of the various structures are described, forming the basis for a more complete kinematical picture of boundary layer physics than has been previously known. In particular, the importance of vortex structures of various forms to the generation of Reynolds shear stress is investigated
Communication system features dual mode range acquisition plus time delay measurement
Communication system combines range acquisition system and time measurement system for tracking high velocity aircraft and spacecraft. The range acquisition system uses a pseudonoise code to determine range and the time measurement system reduces uncontrolled phase variations in the demodulated signal
Identifying capacitive and inductive loss in lumped element superconducting hybrid titanium nitride/aluminum resonators
We present a method to systematically locate and extract capacitive and
inductive losses in superconducting resonators at microwave frequencies by use
of mixed-material, lumped element devices. In these devices, ultra-low loss
titanium nitride was progressively replaced with aluminum in the
inter-digitated capacitor and meandered inductor elements. By measuring the
power dependent loss at 50 mK as the Al-TiN fraction in each element is
increased, we find that at low electric field, i.e. in the single photon limit,
the loss is two level system in nature and is correlated with the amount of Al
capacitance rather than the Al inductance. In the high electric field limit,
the remaining loss is linearly related to the product of the Al area times its
inductance and is likely due to quasiparticles generated by stray radiation. At
elevated temperature, additional loss is correlated with the amount of Al in
the inductance, with a power independent TiN-Al interface loss term that
exponentially decreases as the temperature is reduced. The TiN-Al interface
loss is vanishingly small at the 50 mK base temperature.Comment: 10 pages, 5 figure
Experiments in free shear flows: Status and needs for the future
Experiments in free turbulent flows are recommended with the primary concern placed on classical flows in order to augment understanding and for model building. Five classes of experiments dealing with classical free turbulent flows are outlined and proposed as being of particular significance for the near future. These classes include the following: (1) Experiments clarifying the effect of density variation owing to use of different gases, with and without the additional effect of density variation due to high Mach number or other effects; (2) experiments clarifying the role and importance of various parameters which determine the behavior of the near field as well as the condictions under which any of these parameters can be neglected; (3) experiments determining the cumulative effect of initial conditions in terms of distance to fully established flow; (4) experiments for cases where two layers of distinctly different initial turbulence structure flow side by side at the same mean speed; and (5) experiment using contemporary experimental techniques to study structure in free turbulent shear flows in order to compliment and support contemporary work on boundary layers
Characterization and In-situ Monitoring of Sub-stoichiometric Adjustable Tc Titanium Nitride Growth
The structural and electrical properties of Ti-N films deposited by reactive
sputtering depend on their growth parameters, in particular the Ar:N2 gas
ratio. We show that the nitrogen percentage changes the crystallographic phase
of the film progressively from pure \alpha-Ti, through an \alpha-Ti phase with
interstitial nitrogen, to stoichiometric Ti2N, and through a substoichiometric
TiNX to stoichiometric TiN. These changes also affect the superconducting
transition temperature, Tc, allowing, the superconducting properties to be
tailored for specific applications. After decreasing from a Tc of 0.4 K for
pure Ti down to below 50 mK at the Ti2N point, the Tc then increases rapidly up
to nearly 5 K over a narrow range of nitrogen incorporation. This very sharp
increase of Tc makes it difficult to control the properties of the film from
wafer-to-wafer as well as across a given wafer to within acceptable margins for
device fabrication. Here we show that the nitrogen composition and hence the
superconductive properties are related to, and can be determined by,
spectroscopic ellipsometry. Therefore, this technique may be used for process
control and wafer screening prior to investing time in processing devices
Residual Stress Analysis using Multiparameter Tomographic Reconstruction
While tomographic reconstruction techniques are commonly utilized for the analysis of electromagnetic (typically x-ray) wave propagation data, this approach is infrequently used to examine acoustic data outside the geophysics community. However, acoustic tomography offers some distinct cost and performance advantages over conventional imaging techniques and some unique capabilities which are currently under investigation. One of the most intriguing of the enhanced capabilities is multiparameter imaging. In conventional ultrasonic testing, one usually concentrates on a single parameter of interest, whether it be amplitude, velocity, etc. and for most applications this is fully adequate. This is also true for most tomographic imaging situations such as x-ray tomography where attenuation is sought as the parameter to be obtained from the reconstruction process. However, in many cases, one parameter alone fails to yield full information about the material state even for isotropic media where two independent material stiffness parameters are required for complete characterization. For anisotropic media, the situation becomes increasingly complex with the degree of anisotropy with 21 independent material parameters required. In this work, we address the problem of multiparameter reconstruction and detail a way in which a standard reconstruction technique namely the algebraic reconstruction technique or ART can be modified to achieve this goal. Both isotropic and anisotropic situations are considered. Also, as a practical application of this approach, we address the problem of residual stress determination. Certainly, the use of tomography for residual stress analysis is not new. However, in all these studies, only a single residual stress parameter was reconstructed. This approach is quite satisfactory providing the stress state is uniaxial. Here, we develop a general approach for the tomographic reconstruction of a triaxial stress field
- …