Heteroepitaxial hematite photoanodes as a model system for solar water splitting

Heteroepitaxial multilayer Pt(111)/Fe2O3(0001) films were deposited on sapphire c-plane (0001) substrates by RF magnetron sputtering and pulsed laser deposition, respectively. The films were highly crystalline, displaying an in-plane mosaic spread of less than 1° and a homogenous surface morphology with roughness of ∼3 Å. Ellipsometry and UV-vis spectroscopy measurements were shown to be in excellent agreement with modelling, demonstrating that the optics of the system including absorption in the hematite layer are well described. For polycrystalline hematite photoanodes deposited on platinum, full characterization of the system is hampered by the inability to make measurements in alkaline electrolyte containing hydrogen peroxide (H2O2) due to spontaneous decomposition of H2O2 by the exposed platinum. The pin-hole free high quality of the heteroepitaxial films is demonstrated by the ability to make stable and reproducible measurements in H2O2 containing electrolyte allowing for accurate extraction of charge separation and injection efficiency. The combination of excellent crystalline quality in addition to the well characterized optics and electrochemical properties of the heteroepitaxial hematite photoanodes demonstrate that Al2O3(0001)/Pt(111)/Fe2O3(0001) is a powerful model system for systematic investigation into solar water splitting photoanodes

Defect segregation and its effect on the photoelectrochemical properties of Ti-doped hematite photoanodes for solar water splitting

Optimising the photoelectrochemical performance of hematite photoanodes for solar water splitting requires better understanding of the relationships between dopant distribution, structural defects and photoelectrochemical properties. Here, we use complementary characterisation techniques including electron microscopy, conductive atomic force microscopy (CAFM), Rutherford backscattering spectroscopy (RBS), atom probe tomography (APT) and intensity modulated photocurrent spectroscopy (IMPS) to study this correlation in Ti-doped (1 cat.%) hematite films deposited by pulsed laser deposition (PLD) on F:SnO2 (FTO) coated glass substrates. The deposition was carried out at 300 {\deg}C, followed by annealing at 500 deg C for 2 h. Upon annealing, Ti was observed by APT to segregate to the hematite/FTO interface and into some hematite grains. Since no other pronounced changes in microstructure and chemical composition were observed by electron microscopy and RBS after annealing, the non-uniform Ti redistribution seems to be the reason for a reduced interfacial recombination in the annealed films, as observed by IMPS. This results in a lower onset potential, higher photocurrent and larger fill factor with respect to the as-deposited state. This work provides atomic-scale insights into the microscopic inhomogeneity in Ti-doped hematite thin films and the role of defect segregation in their electrical and photoelectrochemical properties

High quality oxide-free metallic nanoparticles: a strategy for synthesis through laser ablation in aqueous medium

The paper explores the synthesis of oxide-free nanoparticles of Ag and Cu through laser ablation of pure targets under aqueous medium and tuning the quality and size through addition of Polyvinylpyrrolidone (PVP) in the medium. The size distribution of nanoparticles reduces from 37 +/- 30 nm and 13 +/- 5 nm to 32 +/- 12 nm and 4 +/- 1 nm for Ag and Cu with changes in PVP concentration from 0.00 to 0.02 M, respectively. Irregular shaped particles of Ag with Ag2O phase and a Cu-Cu2O core-shell particles form without the addition of PVP, while oxide layer is absent with 0.02 M of PVP. The recent understanding of the mechanism of particle formation during laser ablation under liquid medium allows us to rationalize our observation

Synthesis and Mechanism of Composition and Size Dependent Morphology Selection in Nanoparticles of Ag-Cu Alloys Processed by Laser Ablation Under Liquid Medium

We have synthesized Ag-Cu alloy nanoparticles of four different compositions by using the laser ablation technique with the target under aqueous medium. Following this, we report a morphological transition in the nanoparticles from a normal two-phase microstructure to a structure with random segregation and finally a core shell structure at small sizes as a function of Cu concentration. To illustrate the composition dependence of morphology, we report observations carried out on nanoparticles of two different sizes: similar to 5 and similar to 20 nm. The results could be rationalized through the thermodynamic modeling of free energy of phase mixing and wettability of the alloying phases

Phase formation and stability of alloy phases in free nanoparticles: some insights

This paper explores phase formation and phase stability in free nanoparticles of binary alloys. A procedure for estimating the size and composition dependent free energies incorporating the contributions from the interfaces has been presented. Both single phase solid solution and two phase morphology containing interphase interfaces have been considered. A free energy scenario has been evaluated for two binary alloy systems Ag-Ni and Ag-Cu to predict the microstructure of the alloy nanoparticles at different size ranges as a function of composition. Both Ag-Cu and Ag-Ni systems exhibit wide bulk immiscibility. Ag-Ni nanoparticles were synthesized using the wet chemical synthesis technique whereas Ag-Cu nanoparticles were synthesized using laser ablation of a Ag-Cu target immersed in distilled water. Microstructural and compositional characterization of Ag-Ni and Ag-Cu nanoparticles on a single nanoparticle level was conducted using transmission electron microscopy. Nanoparticle microstructures observed from the microscopic investigation have been correlated with thermodynamic calculation results. It is shown that the observed two phase microstructure consisting of Ag-Ni solid solution in partial decomposed state coexisting with pure Ag phases in the case of Ag-Ni nanoparticles can be only be rationalized by invoking the tendency for phase separation of an initial solid solution with increase in nanoparticle size. Smaller sized Ag-Ni nanoparticles prefer a single phase solid solution microstructure. Due to an increase in particle size during the synthesis process the initial solid solution decomposes into an ultrafine scale phase separated microstructure. We have shown that it is necessary to invoke critical point phenomenon and wetting transition in systems showing a critical point that leads to phase separated Ag-Ni nanoparticles providing a catalytic substrate for the nucleation of equilibrium Ag over it. In the case of the Ag-Cu system, we report the experimental observation of a core shell structure at small sizes. This can be rationalized in terms of a metastable solid solution. It is argued that the nucleation barrier can prevent the formation of biphasic morphology with an internal interface. In such a situation, demixing of the solid solution can bring the system to a lower energy configuration. This has lead to the observed core-shell morphology in the Ag-Cu system during room temperature synthesis

Temperature- and Size-Dependent Compositionally Tuned Microstructural Landscape for Ag-46 Atom % Cu Nanoalloy Prepared by Laser Ablation in Liquid

We report a temperature- and size-dependent compositionally tuned microstructural landscape for Ag-46 atom % Cu alloy nanoparticles. The microstructural and morphological changes were established through the technique of in situ transmission electron microscopy. The nanoparticles were synthesized by laser ablation of alloy target in an aqueous medium. The as-synthesized particles predominantly contain nanosized grains of a single-phase solid solution with grains having sizes ∼3 ± 0.5 nm. For particles with smaller sizes (∼20 nm), the solid solution decomposes and grains coarsen on heating to yield predominantly bicrystals containing two phases of Ag-rich and Cu-rich solid solution. The microstructure of the larger particles (≥40 nm) evolves through segregation of Ag and their preferential growth near the surface of the particles. This leads to a core–shell-like composition distribution at a certain range of temperatures (≥200 °C) and sizes (≥32 nm). At higher temperatures, these core–shell particles undergo a morphological transition through grain growth yielding bicrystals of two phases. We present a size- and temperature-dependent morphology diagram that captures these changes

Synthesis and Mechanism of Composition and Size Dependent Morphology Selection in Nanoparticles of Ag–Cu Alloys Processed by Laser Ablation Under Liquid Medium

We have synthesized Ag–Cu alloy nanoparticles of four different compositions by using the laser ablation technique with the target under aqueous medium. Following this, we report a morphological transition in the nanoparticles from a normal two-phase microstructure to a structure with random segregation and finally a core–shell structure at small sizes as a function of Cu concentration. To illustrate the composition dependence of morphology, we report observations carried out on nanoparticles of two different sizes: ∼5 and ∼20 nm. The results could be rationalized through the thermodynamic modeling of free energy of phase mixing and wettability of the alloying phases