Measured space environmental effects to LDEF during retrieval

On the STS-32 shuttle mission, a space flight experiment provided an understanding of the effects of the space environment on the Long Duration Exposure Facility (LDEF) from rendezvous with the shuttle until removal from the payload bay at the Orbiter Processing Facility (OPF) at KSC. The Interim Operational Contamination Monitor (IOCM) is an attached shuttle payload that has been used on two earlier flights (STS 51C and STS 28) to quantify the contamination deposited during the course of the mission. The IOCM can characterize by direct measurement, the deposition of molecular and particulate contamination during any phase of flight. In addition to these principal measurements, the IOCM actively measures the thermophysical properties of thermal control surfaces by calorimetry, the flux of the ambient atomic oxygen environment, the incident solar flux, and the absolute ambient pressure in the payload bay. The IOCM also provides a structure and sample holders for the exposure of passive material samples to the space environment, e.g. thermal cycling, atomic oxygen, and micrometeoroids and/or orbital debris, etc. One of the more salient results from the STS-32 flight suggests that the LDEF emitted a large number of particulates after berthing into the shuttle. The mission atomic oxygen fluence was also calculated. Although the fluence was low by normal standards, the Kapton passive samples exhibited the onset of erosion. Orbital debris and micrometeoroid impacts also occurred during the retrieval mission. The average perforation diameter was approximately 12.5 microns. The largest perforation diameter was measured at 65 microns

Space shuttle orbiter leading-edge flight performance compared to design goals

Thermo-structural performance of the Space Shuttle orbiter Columbia's leading-edge structural subsystem for the first five (5) flights is compared with the design goals. Lessons learned from thse initial flights of the first reusable manned spacecraft are discussed in order to assess design maturity, deficiencies, and modifications required to rectify the design deficiencies. Flight data and post-flight inspections support the conclusion that the leading-edge structural subsystem hardware performance was outstanding for the initial five (5) flights

Reproductive wastage in sheep

The average lambing performance of Western Australia\u27s ewe flock fluctuates between 60 and 70 per cent. Although this level of performance and variation between years is important for the sheep industry, individual farmers are more concerned about performance of their own flocks. Figure shows the range in lambing performances that exist between farms in this State in 1983-84. The seriously poor performance of many flocks is apparentm - 28 percent of farms had less than 60 per cent lambing. By contrast, 24 farms had performances better than 100 per cent. The reasons for the large differences between farms ( and between years for each farm) lie in the nimber of eggs a ewe sheds at mating, and the wastage that follows through to lamb marking. This review examines the source of reproductive wastage in the ewe. It establishes the importance of the research outlined in the following three articles to improve the performance of ewes

Comparison of 3D scanned human models for off-body communications using motion capture

Body area networks are complex to analyze as there are several channel mechanisms occurring simultaneously, i.e. environmental multipath together with body motion and close coupling between worn antennas and human tissue. Electromagnetic (EM) simulation is an important tool since not all studies can be done on a real human. In order to gain insight into off-body communication involving a worn antenna, this paper uses a 3D animated model obtained from a 3D surface scanner and a motion capture system for full wave simulation of channels at 2.45 and 5.5GHz. To evaluate if the model can represent body area radio channels in general, a comparison of S21 of the simulated model with measurements from 5 other models of similar height to the main test subject is presented

State space collapse and diffusion approximation for a network operating under a fair bandwidth sharing policy

We consider a connection-level model of Internet congestion control, introduced by Massouli\'{e} and Roberts [Telecommunication Systems 15 (2000) 185--201], that represents the randomly varying number of flows present in a network. Here, bandwidth is shared fairly among elastic document transfers according to a weighted $\alpha$-fair bandwidth sharing policy introduced by Mo and Walrand [IEEE/ACM Transactions on Networking 8 (2000) 556--567] [$\alpha\in (0,\infty)$]. Assuming Poisson arrivals and exponentially distributed document sizes, we focus on the heavy traffic regime in which the average load placed on each resource is approximately equal to its capacity. A fluid model (or functional law of large numbers approximation) for this stochastic model was derived and analyzed in a prior work [Ann. Appl. Probab. 14 (2004) 1055--1083] by two of the authors. Here, we use the long-time behavior of the solutions of the fluid model established in that paper to derive a property called multiplicative state space collapse, which, loosely speaking, shows that in diffusion scale, the flow count process for the stochastic model can be approximately recovered as a continuous lifting of the workload process.Comment: Published in at http://dx.doi.org/10.1214/08-AAP591 the Annals of Applied Probability (http://www.imstat.org/aap/) by the Institute of Mathematical Statistics (http://www.imstat.org

LED instrument approach instruction display

A display employing light emitting diodes (LED's) was developed to demonstrate the feasibility of such displays for presenting landing and navigation information to reduce the workload of general aviation pilots during IFR flight. The display consists of a paper tape reader, digital memory, control electronics, digital latches, and LED alphanumeric displays. A presentable digital countdown clock-timer is included as part of the system to provide a convenient means of monitoring time intervals for precise flight navigation. The system is a limited capability prototype assembled to test pilot reaction to such a device under simulated IFR operation. Pilot opinion indicates that the display is helpful in reducing the IFR pilots workload when used with a runway approach plate. However, the development of a compact, low power second generation display was recommended which could present several instructions simultaneously and provide information update capability. A microprocessor-based display could fulfill these requirements