39 research outputs found
Heat transfer to laminar flow over a double backward-facing step
Heat transfer and laminar air flow over a double backward-facing step numerically studied in this paper. The simulations was performed by using ANSYS ICEM for meshing process and using ANSYS fluent 14 (CFD) for solving. The k-ɛ standard model adopted with Reynolds number varied between 98.5 to 512 and three step height at constant heat flux (q=2000 W/m2). The top of wall and bottom of upstream are insulated with bottom of downstream is heated. The results show increase in Nusselt number with increases of Reynolds number for all cases and the maximum of Nusselt number happens at the first step in compared to the second step. Due to increase of cross section area of downstream to generate sudden expansion then Nusselt number decrease but the profile of Nusselt number keep same trend for all cases where increase after the first and second steps. Recirculation region after the first and second steps are denoted by contour of streamline velocity. The higher augmentation of heat transfer rate observed for case 1 at Reynolds number of 512 and heat flux q=2000 W/m2
Numerical Investigation of Heat Transfer Enhancement in a Rectangular Heated Pipe for Turbulent Nanofluid
Thermal characteristics of turbulent nanofluid flow in a rectangular pipe have been investigated numerically. The continuity, momentum, and energy equations were solved by means of a finite volume method (FVM). The symmetrical rectangular channel is heated at the top and bottom at a constant heat flux while the sides walls are insulated. Four different types of nanoparticles Al2O3, ZnO, CuO, and SiO2 at different volume fractions of nanofluids in the range of 1% to 5% are considered in the present investigation. In this paper, effect of different Reynolds numbers in the range of 5000 < Re < 25000 on heat transfer characteristics of nanofluids flowing through the channel is investigated. The numerical results indicate that SiO2-water has the highest Nusselt number compared to other nanofluids while it has the lowest heat transfer coefficient due to low thermal conductivity. The Nusselt number increases with the increase of the Reynolds number and the volume fraction of nanoparticles. The results of simulation show a good agreement with the existing experimental correlations
Detection of the gas–liquid two-phase flow regimes using non-intrusive microwave cylindrical cavity sensor
Gas–liquid two-phase flow phenomenon occurs in various engineering applications and the measurement of it is important. A microwave sensor in the form of a cylindrical cavity has been designed to operate between 5 and 5.7 GHz. The aim is to analyse a two phase gas–liquid flow regime in a pipeline. LabVIEW software is utilised to capture the data, process them and display the results in real time. The results have shown that the microwave sensor has successfully detected the two-phase flow regimes in both the static and dynamic flow environments with reasonable accuracy. The study has also shown the independence of the technique and its accuracy to the temperature change (28–83 °C). Several flow regimes of the gas–liquid two-phase flow have been discussed. The system is also able to detect the stratified, wavy, elongated bubbles and homogeneous flow regimes
Energy, exergy and economic analysis of liquid flat-plate solar collector using green covalent functionalized graphene nanoplatelets
The conventional method of synthesizing carbon-based nanofluids produces harmful products that are highly toxic and hazardous. The present investigation deals with the effects of using eco-friendly, non-corrosive, covalent functionalized Graphene Nanoplatelets with gallic acid (GGNPs) as heat transfer fluid on energetic and exergetic performance of a Liquid flat-plate solar collector (LFPSC). Long-term dispersible stable GGNP nanofluids with base fluid distilled water are prepared with different weight concentrations of 0.025%, 0.05% & 0.1%. For varying concentrations, fluid flow rates of 0.8, 1.2, and 1.5 L/min, heat flux intensities of 600, 800, and 1000 W/m(2), and inlet temperature ranging from 303 to 323 K are considered for the conduction of experiments. Improvement in energy and exergetic efficiency was achieved using GGNP nanofluids. Thermal efficiency surges with increment in flow rate and heat flux intensities, meanwhile it decreases for increment in inlet temperature. The maximum enhancement in LFPSC efficiency is 24.09% for 0.1 wt% GGNPs and flow rate of 1.5 L/min than distilled water. Analysis of exergetic performance revealed that exergy efficiency reduces with a rise in mass flow rate meanwhile enhanced with an increase in nanofluid concentration. Exergy efficiency was maximum for 0.1% GGNP concentration and flow rate of 0.8 L/min. The maximum increase in friction factor values is approximately 1.5, 2.6 and 7.9% for 0.025, 0.05 and 0.1% GGNP nanofluids than distilled water. Relative pumping power slightly increases with the increment of GGNP concentration but is quite close to that of the base fluid. Performance index greater than one is obtained with higher values achieved at an increase in GGNP weight concentration. Economic consideration of GGNP nanofluids in LFPSC showcased a maximum reduction of 26.41% in the size of collector area using 0.1% GGNP nanofluid instead of distilled water. The payback period for LFPSC using GGNPs was 5.615% lesser than that of using water
A CFD study of turbulent heat transfer and fluid flow through the channel with semicircle rib
In the present paper turbulent heat transfer and fluid flow through the channel with semicircle ribs numerically studied. The SST k-ω turbulence Model with finite volume method was employed in simulation. The adopted boundary condition considered step heights of ribs varied from 2.5mm to 10mm with pitch ratio different from 2.5 to 40 and flow Reynolds number between 10000 to 25000 at constant surface temperature. The computational results showed recirculation region after each ribs which effect on performance of heat transfer rate. Increase of Reynolds number and number of ribs leads to increase in heat transfer coefficient. Step height and pitch ratio of ribs increase local heat transfer coefficient along the channel. This simulation has been done by ANSYS 14 FLUENT
Graphene nanoplatelets suspended in different basefluids based solar collector: An experimental and analytical study
© 2021 by the authors. Licensee MDPI, Basel, Switzerland. A flat plate solar collector (FPSC) was analytically studied, with functionalized graphene nanoplatelets (f-GNPs) as its working fluid. Four samples (wt % nanofluids) were prepared in different base fluids such as ethylene glycol (EG), distilled water (DW):EG (70:30), and DW:EG (50:50). Experimental results (via DW) were used to verify the effectiveness of the analytical model. Some of the operating conditions were taken into account in this research, including temperatures, power, and mass flow rates. Experimental techniques were used to elucidate the modified nanofluids’ physicochemical properties, such as its particle sizes, stability, and morphology, involving electron microscopes (EMs), UV–VIS, and X-ray techniques. Differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA) were applied to test the thermal analysis. The findings confirmed that the use of f-GNPs nanofluids enhanced the performance of the FPSC relative to the use of base fluids for all testing conditions. The maximum enhancement of the collector’s effectiveness at a mass flow rate of 1.5 kg min−1 and a weight concentration of 0.1 wt %, increased to 12.69%, 12.60%, and 12.62% in the case of EG, DW:EG (70:30), and DW:EG (50:50), respectively. The results also confirmed an improvement in both the heat gain (FR(τα)) and heat loss (FRUL) coefficients for the f-GNPs nanofluid
Numerical study of turbulent heat transfer in separated flow: review
The numerical studies of turbulent heat transfer in separation flow presented in this paper. Enhancement of heat transfer rate in turbulent separation flow at sudden expansion in passage, over forward or backward facing-steps, blunt body, ribs channel, and swirl generators in channels were investigated numerically. Different models (CFD) used to study heat transfer characteristics and fluid flow in separation and reattachment region and compared results with previous experimental data. The effect of expansion ratio, Reynolds number, step height, (shape, number, and angle) of ribs and (length, twist angle, and gap width) twist the tape on improvement of heat transfer were referred. The numerical results indicated increases of heat transfer coefficients with increases in the above parameters. The numerical simulations derived from finite volume, element, and difference methods for evaluation of turbulent heat transfer in separated flow and employed several computational programs
Design and implementation of a non-invasive real-time microwave sensor for assessing water hardness in heat exchangers
A non-invasive-monitoring of concentration and dielectric properties of calcium hardness in heat exchanger cooling water was conducted with a 2.5 GHz microwave cavity resonator designed and fabricated locally for the experiment. The principle of electric dipole moment theories were used to analyse the sample solution that occurs as a function of calcium ion content. Artificial difference of water hardness was prepared by mixing CaCl 2 in deionised water . The sample was centrally positioned in the electric field of the TM 010 mode of a resonant cylindrical cavity. COMSOL simulation package was used to compare and validate the experimental cavity resonator frequency. Transmission signal (S 21 ) measurements via vector network analyser at different concentrations were observed a linear relationship in amplitude with different frequency changes. In addition, calcium absorption provides a first-order change in material polarisation (i.e. real permittivity), and second-order transitions associated dielectric losses (i.e. imaginary permittivity). These research findings introduce a novel technique of real-time monitoring of water hardness concentration by using non-invasive microwave sensor. © 2017 Informa UK Limited, trading as Taylor & Francis Grou