128 research outputs found
Superspreading: Mechanisms and Molecular Design
The
intriguing ability of certain surfactant molecules to drive
the superspreading of liquids to complete wetting on hydrophobic substrates
is central to numerous applications that range from coating flow technology
to enhanced oil recovery. Despite significant experimental efforts,
the precise mechanisms underlying superspreading remain unknown to
date. Here, we isolate these mechanisms by analyzing coarse-grained
molecular dynamics simulations of surfactant molecules of varying
molecular architecture and substrate affinity. We observe that for
superspreading to occur, two key conditions must be simultaneously
satisfied: the adsorption of surfactants from the liquid–vapor
surface onto the three-phase contact line augmented by local bilayer
formation. Crucially, this must be coordinated with the rapid replenishment
of liquid–vapor and solid–liquid interfaces with surfactants
from the interior of the droplet. This article also highlights and
explores the differences between superspreading and conventional surfactants,
paving the way for the design of molecular architectures tailored
specifically for applications that rely on the control of wetting
Low-surface energy surfactants with branched hydrocarbon architectures
International audienceSurface tensiometry and small-angle neutron scattering have been used to characterize a new class of low-surface energy surfactants (LSESs), "hedgehog" surfactants. These surfactants are based on highly branched hydrocarbon (HC) chains as replacements for environmentally hazardous fluorocarbon surfactants and polymers. Tensiometric analyses indicate that a subtle structural modification in the tails and headgroup results in significant effects on limiting surface tensions Îłcmc at the critical micelle concentration: a higher level of branching and an increased counterion size promote an effective reduction of surface tension to low values for HC surfactants (Îłcmc 24 mN m-1). These LSESs present a new class of potentially very important materials, which form lamellar aggregates in aqueous solutions independent of dilution
The effect of salts on the liquid–liquid phase equilibria of PEG600 + salt aqueous two-phase systems
Six new ATPSs were prepared by combining polyethylene glycol PEG600 with potassium citrate, dipotassium hydrogen phosphate, sodium formate, potassium formate, sodium sulfate, and lithium sulfate. Complete phase diagrams, including the binodal curve and three tie-lines, were determined at 23 °C. The experimental data obtained for the binodal curve were successfully adjusted to the Merchuk equation, and the reliability of tie-line data was confirmed using the equations suggested by Othmer–Tobias and Bancroft. The ability of each ion to induce ATPS formation was investigated. Na+ proved to be more effective in ATPS formation than K+ and Li+. For potassium salts, the order observed for the effectiveness of the anions was: HPO42– > C6H5O73– > HCO2–. Regarding the sodium salts, it was found that SO42– is clearly more effective than HCO2–. The position of the ions in the Hofmeister series and their free energy of hydration (ΔGhyd) were used to explain the ability of the ions to induce PEG salting-out. Furthermore, the effective excluded volume (EEV) of the salts was determined and the following order was found: Na2SO4 > K2HPO4 > Li2SO4 > K3C6H5O7 > NaCHO2 > KCHO2. Similar order was obtained when analyzing the size of the heterogeneous regions, suggesting the practical use of EEV as a comparison parameter between different ATPSs.This work is partially supported by project PEst-C/EQB/LA0020/2011, financed by FEDER through COMPETE-Programa Operacional Factores de Competitividade and by FCT-Fundacao para a Ciencia e a Tecnologia. Sara Silverio acknowledges her Ph.D. grant from FCT (SFRH/BD/43439/2008)
Surfactants at the design limit
This document is the Accepted Manuscript version of a Published Work that appeared in final form in Langmuir, copyright © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see https://doi.org/10.1021/acs.langmuir.5b00336This article analyzes how the individual structural elements of surfactant molecules affect surface properties, in particular, the point of reference defined by the limiting surface tension at the aqueous cmc, γcmc. Particular emphasis is given to how the chemical nature and structure of the hydrophobic tails influence γcmc. By comparing the three different classes of surfactants, fluorocarbon, silicone, and hydrocarbon, a generalized surface packing index is introduced which is independent of the chemical nature of the surfactants. This parameter ϕcmc represents the volume fraction of surfactant chain fragments in a surface film at the aqueous cmc. It is shown that ϕcmc is a useful index for understanding the limiting surface tension of surfactants and can be useful for designing new superefficient surfactants
- …