89,814 research outputs found
The effect of delta 3 on a yawing HAWT blade and on yaw dynamics
A single degree of freedom aeroelastic computer model, WMSTAB3, was employed to perform a parametric analysis of HAWT blade behavior during yaw maneuvers. Over 1,000 different combinations of delta sub 3 and normal frequency were analyzed. The effect of delta sub 3 and flapping stiffness on flapping frequency, phase, and magnitude are discussed. The moments transmitted to the fixed system during yaw maneuvers were calculated and reduced to time constants of response to step changes in wind direction. The significance of the time constants for the configurations considered relative to yaw response rate and lag angle is discussed, along with their possible significance for large HAWT
The galactic halo question: New size constraints from galactic gamma-ray data
The SAS-2 gamma-ray data is analyzed making use of recent CO line emission and other data for determining the large-scale distribution of galactic gas. A nonuniform distribution of cosmic rays in the galaxy is implied. This fact rules out large trapping halo models and extragalactic origin models. Detailed models of diffusion halos of various sizes perpendicular to the galactic plane are considered. In such models, the scale perpendicular to the plane has a strong effect in determining the radial distribution of cosmic rays. Such radial distributions are calculated for cylindrical coordinate models. The implied gamma-ray longitude distributions are then calculated and compared with the SAS-2 data for goodness-of-fit. Assuming the sources to be supernova remnants or pulsars, cosmic ray nucleon halo models with scale heights greater than 3 kpc are found to provide a poor fit to the gamma-ray longitude data (probability of 6% or less). Thin halo, or source dominated diffusion models are found to provide a good fit to the gamma-ray data, with an upper limit scale height of approximately 3 kpc
Overdensities of SMGs around WISE-selected, ultra-luminous, high-redshift galaxies
Submillimetre (submm) observations of WISE-selected, dusty, luminous,
high-redshift galaxies have revealed intriguing overdensities around them on
arcmin scales. They could be the best signposts of overdense environments on
the sky.Comment: ALMA Conference Proceedings December 2014 2 page
Boundary lubrication and thermal stability studies with five liquid lubricants in nitrogen to 400 C
Steel friction and wear tests in nitrogen with paraffinic resins, synthetic paraffinic oil, glycol, and ester lubricants including thermal stability at high temperature
State-of-the-art of turbofan engine noise control
The technology of turbofan engine noise reduction is surveyed. Specific topics discussed include: (1) new fans for low noise; (2) fan and core noise suppression; (3) turbomachinery noise sources; and (4) a new program for improving static noise testing of fans and engines
Fracture behavior of unidirectional boron/aluminum composite laminates
An experiment was conducted to verify the results of mathematical models which predict the stresses and displacements of fibers and the amount of damage growth in a center-notched lamina as a function of the applied remote stress and the matrix and fiber material properties. A brittle lacquer coating was used to detect the yielding in the matrix while X-ray techniques were used to determine the number of broken fibers in the laminate. The notched strengths and the amounts of damage found in the specimens agree well with those predicted by the mathematical model. It is shown that the amount of damage and the crack opening displacement does not depend strongly on the number of plies in the laminate for a given notch width. By heat-treating certain laminates to increase the yield stress of the alumina matrix, the effect of different matrix properties on the fracture behavior was investigated. The stronger matrix is shown to weaken the notched laminate by decreasing the amount of matrix damage, thereby making the laminate more notch sensitive
Effect of sterilization irradiation on friction and wear of ultrahigh-molecular-weight polyethylene
The effect of sterilization gamma irradiation on the friction and wear properties of ultrahigh molecular weight polyethylene (UHMWPE) sliding against 316L stainless steel in dry air at 23 C was determined. A pin-on-disk apparatus was used. Experimental conditions included a 1-kilogram load, a 0.061- to 0.27-meter-per-second sliding velocity, and a 32000- to 578000-meter sliding distance. Although sterilization doses of 2.5 and 5.0 megarads greatly altered the average molecular weight and the molecular weight distribution, the friction and wear properties of the polymer were not significantly changed
Fabrication and wear test of a continuous fiber/particulate composite total surface hip replacement
Continuous fiber woven E-glass composite femoral shells having the ame elastic properties as bone were fabricated. The shells were then encrusted with filled epoxy wear resistant coatings and run dry against ultrahigh molecular weight polyethylene acetabular cups in 42,000 and 250,000 cycle were tests on a total hip simulator. The tribological characteristics of these shells atriculating with the acetabular cups are comparable to a vitallium bal articulating with an ultrahigh molecular weight polyethylene cup
The rich cluster of galaxies ABCG 85. III. Analyzing the ABCG 85/87/89 complex
We present a combined X-ray and optical analysis of the ABCG 85/87/89 complex
of clusters of galaxies, based on the ROSAT PSPC image, optical photometric
catalogues (Slezak et al. 1998), and an optical redshift catalogue (Durret et
al. 1998). From this combined data set, we find striking alignments at all
scales at PA160\deg. At small scales, the cD galaxy in ABCG 85 and the
brightest galaxies in the cluster are aligned along this PA. At a larger scale,
X-ray emission defines a comparable PA south-southeast of ABCG 85 towards ABCG
87, with a patchy X-ray structure very different from the regular shape of the
optical galaxy distribution in ABCG 87. The galaxy velocities in the ABCG 87
region show the existence of subgroups, which all have an X-ray counterpart,
and seem to be falling onto ABCG 85 along a filament almost perpendicular to
the plane of the sky. To the west of ABCG 85, ABCG 89 appears as a significant
galaxy density enhancement, but is barely detected at X-ray wavelengths. The
galaxy velocities reveal that in fact this is not a cluster but two groups with
very different velocities superimposed along the line of sight. These two
groups appear to be located in intersecting sheets on opposite sides of a large
bubble. These data and their interpretation reinforce the cosmological scenario
in which matter, including galaxies, groups and gas, falls onto the cluster
along a filament.Comment: accepted for publication in Astronomy & Astrophysic
Tribological characteristics of a composite total-surface hip replacement
Continuous fiber, woven E glass composite femoral shells having the same elastic properties as bone were fabricated. The shells were then encrusted with filled epoxy wear resistant coatings and run dry against ultrahigh molecular weight polyethylene acetabular cups in 42,000 and 250,000 cycle wear tests on a total hip simulator. The tribological characteristics of these continuous fiber particulate composite femoral shells articulating with ultrahigh molecular weight polyethylene acetabular cups were comparable to those of a vitallium ball articulating with an ultrahigh molecular weight polyethylene acetabular cup
- …