Ozone as oxidation agent in cyclic activation of biochar

Granular activated carbons were produced from grape seed biochar by cyclic activation with ozone. In each cycle, char was first oxidized by exposure to ozone and then subjected to high temperature in inert atmosphere to desorb oxygen groups formed. The study assessed the influence of operating conditions in the development of porosity, from a starting biochar with narrow microporosity (SBET: 47 m2 g− 1, SDA: 505 m2g− 1) prepared by flash pyrolysis of grape seed at 800 °C. The variables studied were the number of cycles applied and the oxidation and desorption temperatures (250–275 and 850–950 °C, respectively). High oxidation temperatures led to higher burn-off, which was also found to increase with the number of activation cycles. The burn-off needed to achieve a high surface area was lower than in conventional physical activation. After 7–9 activation cycles, activated carbons with SBET higher than 1200 m2 g− 1 and SDA above 1500 m2 g− 1 were obtained. The use of ozone resulted in mainly microporous activated carbons (0.37–0.52 cm3 g− 1) with very low contribution of mesopores (< 0.04–0.07 cm3 g− 1). The mean micropore size increased with the number of activation cycles due to pore widening, while mesopore mean size decreased along the cycles. The activated carbons showed a unique granular morphology with a hollow core and a porous shell, which is maintained even after 10 activation cyclesThe authors greatly appreciatefinancial support from the Spanish Ministerio de Ciencia e Innovación (CTQ2012-32821

Preparation of granular activated carbons from grape seeds by cycles of liquid phase oxidation and thermal desorption

Activation of grape seed char upon successive cycles of liquid phase oxidation followed by high temperature desorption permits a tailored development of porosity. In this work three different oxidants (HNO3, H 2O2, and (NH4)2S2O 8), have been tested and the desorption temperature has been varied within 850-950 C upon 10 activation cycles. A high increase of BET surface area was observed in the first five cycles with HNO3 as oxidizing agent giving rise to values higher than 1200 m2 g- 1 at around 50% burn-off. Activation with H2O2 and (NH 4)2S2O8 led to a significantly lower development of surface area, with 600 and 800 m2 g- 1 respectively at that burn-off. The analysis of the pore size distribution showed that porosity was generated through the creation of new micropores and widening of existing ones upon activation with HNO3 and (NH4) 2S2O8, whereas H2O2 mostly led to the widening of the narrow micropores already existing in the starting char. The activated carbons obtained are essentially microporous, with some small contribution of mesoporosity in the HNO3 series (V micro = 0.69 cm3 g- 1; Vmeso = 0.07 cm3 g- 1). SEM images showed that the activated carbons maintained the granular morphology of the seeds after 10 cycles showing a hollow core structure with a wall thickness of about 200 μmThe authors greatly appreciate the financial support from the Spanish Ministerio de Ciencia e Innovación (CTQ2009-09983

Granular mesoporous activated carbons from waste tires by cyclic oxygen chemisorption-desorption

This document is the accepted manuscript version of a published work that appeared in final form in Industrial and Engineering Chemistry Research, © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see https://pubs.acs.org/doi/10.1021/ie201499hActivation upon cyclic oxygen chemisorption-desorption has proved to be an efficient way to develop porosity at low burn off from waste tires char. In this work the influence of particle size, desorption temperature, and the number of cycles is studied. Highest values of burnoff and specific surface area (S BET) are obtained for the largest particle diameter (3 mm average) and at intermediate desorption temperature (650 °C). In these conditions S BET values around 500 m 2/g can be achieved at burn-offs of about 30%, and close to 600 m 2/g at around 45% burnoff, with a mean pore size of 10 nm and a micropore volume close to 0.08 cm 3/g. Although the surface area is moderate, the low burnoff and high S BET/burnoff ratio achieved make it possible to maintain initial granular morphology of the particles even after 20 cycles of activationWe greatly appreciate finantial support from the Spanish Ministerio de Educacion y Ciencia through the project CTQ2009-0998

Porous structure and morphology of granular chars from flash and conventional pyrolysis of grape seeds

This work studies the influence of the operating conditions used in the pyrolysis of grape seeds on the morphology and textural properties of the chars resulting. Flash and conventional (283Kmin-1 heating rate) pyrolysis have been used within a wide range of temperature (300-1000°C). The effect of a pretreatment for oil extraction has also been studied. The porous structure of the chars was characterized by adsorption of N2 at 77K, Ar at 77K and 87K, and CO2 at 273K and mercury intrusion porosimetry. The morphology was analyzed by scanning electron microscopy. All the materials prepared revealed an essentially microporous structure, with a poor or even negligible contribution of mesopores. Increasing pyrolysis temperature led to higher specific surface areas and lower pore size. The highest specific surface area values occurred within 700-800°C, reaching up to 500m2g-1 with pore sizes in the 0.4-1.1nm range. No significant morphological changes were observed upon carbonization so that the resulting chars were granular materials of similar size than the starting grape seeds. The hollow core structure of the chars, with most of the material allocated at the periphery of the granules can help to overcome the mass transfer limitations of most common (solid or massive) granular activated carbons. The chars showed a good mechanical strength during attrition tests. These chars can be potential candidates for the preparation of granular carbons molecular sieve or activated carbons raw materialsThe authors greatly appreciate financial support from the Spanish Ministerio de Ciencia e Innovación (CTQ2009-09983

Biomass-Derived Microporous Carbon Materials with an Open Structure of Cross-Linked Sub-microfibers with Enhanced Adsorption Characteristics

This document is the accepted manuscript version of a published work that appeared in final form in Energy and Fuels, © American Chemical Society after peer review and technical editing by the publisher. To access the final edited and published work see https://pubs.acs.org/doi/abs/10.1021/acs.energyfuels.6b02112Moringa oleifera seed shells exhibit a unique structure of cross-linked sub-microfibers (0.5-1.5 μm diameter) with a well-connected macroporous network. Controlled pyrolysis (500-800 °C) and cyclic activation of the precursor provided a porous carbon material with a structure that minimizes mass-transfer constraints. Under both slow (10 °C/min-1) and flash pyrolysis, the structure was preserved, while a significant microporosity was developed. By flash pyrolysis (700-800 °C), a material with enhanced characteristics for potential application as a molecular sieve (SDA = 450-470 m2 g-1, and SBET = 5 m2 g-1) was obtained. Cyclic activation of carbonized shells, consisting of an oxygen chemisorption stage (180 °C) followed by a desorption stage in an inert atmosphere (450-900 °C), resulted in a controlled development of microporosity upon successive activation cycles. After 10 activation cycles, respective SDA and SBET values of 1172 and 761 m2 g-1 were obtained. Higher development of the surface area and a wider distribution of micropores was observed when the desorption stage was carried out at 900 °C. The development of the surface area was achieved at low burnoff (22-33%), thus preserving the structure of the material. Thanks to its unique structure, the material obtained exhibited enhanced characteristics for gas sorption as a result of diminished mass-transfer limitations, assessed through the kinetics of carbon dioxide adsorption runs at ambient conditionsThe authors greatly appreciate financial support from the Spanish Ministerio de Economía y Competitividad (CTQ2012-32821

Impact of COVID-19 on cardiovascular testing in the United States versus the rest of the world

Objectives: This study sought to quantify and compare the decline in volumes of cardiovascular procedures between the United States and non-US institutions during the early phase of the coronavirus disease-2019 (COVID-19) pandemic. Background: The COVID-19 pandemic has disrupted the care of many non-COVID-19 illnesses. Reductions in diagnostic cardiovascular testing around the world have led to concerns over the implications of reduced testing for cardiovascular disease (CVD) morbidity and mortality. Methods: Data were submitted to the INCAPS-COVID (International Atomic Energy Agency Non-Invasive Cardiology Protocols Study of COVID-19), a multinational registry comprising 909 institutions in 108 countries (including 155 facilities in 40 U.S. states), assessing the impact of the COVID-19 pandemic on volumes of diagnostic cardiovascular procedures. Data were obtained for April 2020 and compared with volumes of baseline procedures from March 2019. We compared laboratory characteristics, practices, and procedure volumes between U.S. and non-U.S. facilities and between U.S. geographic regions and identified factors associated with volume reduction in the United States. Results: Reductions in the volumes of procedures in the United States were similar to those in non-U.S. facilities (68% vs. 63%, respectively; p = 0.237), although U.S. facilities reported greater reductions in invasive coronary angiography (69% vs. 53%, respectively; p < 0.001). Significantly more U.S. facilities reported increased use of telehealth and patient screening measures than non-U.S. facilities, such as temperature checks, symptom screenings, and COVID-19 testing. Reductions in volumes of procedures differed between U.S. regions, with larger declines observed in the Northeast (76%) and Midwest (74%) than in the South (62%) and West (44%). Prevalence of COVID-19, staff redeployments, outpatient centers, and urban centers were associated with greater reductions in volume in U.S. facilities in a multivariable analysis. Conclusions: We observed marked reductions in U.S. cardiovascular testing in the early phase of the pandemic and significant variability between U.S. regions. The association between reductions of volumes and COVID-19 prevalence in the United States highlighted the need for proactive efforts to maintain access to cardiovascular testing in areas most affected by outbreaks of COVID-19 infection

Robust estimation of bacterial cell count from optical density

Optical density (OD) is widely used to estimate the density of cells in liquid culture, but cannot be compared between instruments without a standardized calibration protocol and is challenging to relate to actual cell count. We address this with an interlaboratory study comparing three simple, low-cost, and highly accessible OD calibration protocols across 244 laboratories, applied to eight strains of constitutive GFP-expressing E. coli. Based on our results, we recommend calibrating OD to estimated cell count using serial dilution of silica microspheres, which produces highly precise calibration (95.5% of residuals &lt;1.2-fold), is easily assessed for quality control, also assesses instrument effective linear range, and can be combined with fluorescence calibration to obtain units of Molecules of Equivalent Fluorescein (MEFL) per cell, allowing direct comparison and data fusion with flow cytometry measurements: in our study, fluorescence per cell measurements showed only a 1.07-fold mean difference between plate reader and flow cytometry data

Massive Parallel Analysis of Single Cells in an Integrated Microfluidic Platform

New tools that facilitate the study of cell-to-cell variability could help uncover novel cellular regulation mechanisms. We present an integrated microfluidic platform to analyze a large number of single cells in parallel. To isolate and analyze thousands of individual cells in multiplexed conditions, our platform incorporates arrays of microwells (7 pL each) in a multilayered microfluidic device. The device allows the simultaneous loading of cells into 16 separate chambers, each containing 4640 microwells, for a total of 74 240 wells per device. We characterized different parameters important for the operation of the microfluidic device including flow rate, solution exchange rate in a microchamber, shear stress, and time to fill up a single microwell with molecules of different molecular weight. In general, after ∼7.5 min of cell loading our device has an 80% microwell occupancy with 1–4 cells, of which 36% of wells contained a single cell. To test the functionality of our device, we carried out a cell viability assay with adherent and nonadherent cells. We also studied the production of neutrophil extracellular traps (NETs) from single neutrophils isolated from peripheral blood, observing the existence of temporal heterogeneity in NETs production, perhaps having implications in the type of the neutrophil response to an infection or inflammation. We foresee our platform will have a variety of applications in drug discovery and cellular biology by facilitating the characterization of phenotypic differences in a monoclonal cell population

Reduction of cardiac imaging tests during the COVID-19 pandemic: The case of Italy. Findings from the IAEA Non-invasive Cardiology Protocol Survey on COVID-19 (INCAPS COVID)

Background: In early 2020, COVID-19 massively hit Italy, earlier and harder than any other European country. This caused a series of strict containment measures, aimed at blocking the spread of the pandemic. Healthcare delivery was also affected when resources were diverted towards care of COVID-19 patients, including intensive care wards. Aim of the study: The aim is assessing the impact of COVID-19 on cardiac imaging in Italy, compare to the Rest of Europe (RoE) and the World (RoW). Methods: A global survey was conducted in May–June 2020 worldwide, through a questionnaire distributed online. The survey covered three periods: March and April 2020, and March 2019. Data from 52 Italian centres, a subset of the 909 participating centres from 108 countries, were analyzed. Results: In Italy, volumes decreased by 67% in March 2020, compared to March 2019, as opposed to a significantly lower decrease (p &lt; 0.001) in RoE and RoW (41% and 40%, respectively). A further decrease from March 2020 to April 2020 summed up to 76% for the North, 77% for the Centre and 86% for the South. When compared to the RoE and RoW, this further decrease from March 2020 to April 2020 in Italy was significantly less (p = 0.005), most likely reflecting the earlier effects of the containment measures in Italy, taken earlier than anywhere else in the West. Conclusions: The COVID-19 pandemic massively hit Italy and caused a disruption of healthcare services, including cardiac imaging studies. This raises concern about the medium- and long-term consequences for the high number of patients who were denied timely diagnoses and the subsequent lifesaving therapies and procedures

International Impact of COVID-19 on the Diagnosis of Heart Disease

Background: The coronavirus disease 2019 (COVID-19) pandemic has adversely affected diagnosis and treatment of noncommunicable diseases. Its effects on delivery of diagnostic care for cardiovascular disease, which remains the leading cause of death worldwide, have not been quantified. Objectives: The study sought to assess COVID-19's impact on global cardiovascular diagnostic procedural volumes and safety practices. Methods: The International Atomic Energy Agency conducted a worldwide survey assessing alterations in cardiovascular procedure volumes and safety practices resulting from COVID-19. Noninvasive and invasive cardiac testing volumes were obtained from participating sites for March and April 2020 and compared with those from March 2019. Availability of personal protective equipment and pandemic-related testing practice changes were ascertained. Results: Surveys were submitted from 909 inpatient and outpatient centers performing cardiac diagnostic procedures, in 108 countries. Procedure volumes decreased 42% from March 2019 to March 2020, and 64% from March 2019 to April 2020. Transthoracic echocardiography decreased by 59%, transesophageal echocardiography 76%, and stress tests 78%, which varied between stress modalities. Coronary angiography (invasive or computed tomography) decreased 55% (p &lt; 0.001 for each procedure). In multivariable regression, significantly greater reduction in procedures occurred for centers in countries with lower gross domestic product. Location in a low-income and lower–middle-income country was associated with an additional 22% reduction in cardiac procedures and less availability of personal protective equipment and telehealth. Conclusions: COVID-19 was associated with a significant and abrupt reduction in cardiovascular diagnostic testing across the globe, especially affecting the world's economically challenged. Further study of cardiovascular outcomes and COVID-19–related changes in care delivery is warranted