11 research outputs found

    Existence of a Tribo-Modified Surface Layer on SBR Elastomers: Balance Between Formation and Wear of the Modified Layer

    Get PDF
    In most of the tribological contacts, the composition and tribological properties of the original interface will change during use. The tribo-films, with modified properties compared to the bulk, are dynamic structures that play a significant role in friction. The existence of a tribo-modified surface layer and its importance on the overall friction of elastomers has been shown both theoretically and experimentally before. The characteristics of the modified surface layer deserve specific attention since the tribological properties of elastomers in contact with a rough counter-surface are determined by these modified surfaces together with the properties of bulk of the material. Both the formation of the modified layer and the break down (wear) of it are of importance in determining the existence and thickness of the tribo-modified layer. In this study, the importance of the wear is emphasized by comparing two styrene butadiene rubber-based elastomers in contact with a granite sphere. A current status of perception of the removal and the stability of the modified surface layers on rubbers is introduced as well as experimental work related to this matter and discussion within literature. Pin-on-disk friction tests are performed on two SBR-based samples in contact with a granite sphere under controlled environmental conditions to form the modified surface layer. Although the hysteresis part of the friction force which has a minor contribution in the overall friction is not markedly different, the total measured friction coefficient differs significantly. Mechanical changes both inside and outside the wear track are determined by atomic force microscope nano-indentations at different timescales to examine the modified surface layer on the test samples. The specific wear rates of the two tribo-systems are compared, and the existence of the modified surface layer, the different measured friction coefficient and the running-in distances toward steady-state friction are explained considering different wear rates. A conceptual model is presented, correlating the energy input into the tribo-system and the existence of a modified surface layer

    The Effect of Silanization Temperature and Time on the Marching Modulus of Silica-Filled Tire Tread Compounds

    No full text
    Marching modulus phenomena are often observed in silica-reinforced solution styrene–butadiene rubber/butadiene rubber (S-SBR/BR) tire tread compounds. When such a situation happens, it is difficult to determine the optimum curing time, and as a consequence the physical properties of the rubber vulcanizates may vary. Previous studies have demonstrated that the curing behavior of silica compounds is related to the degree of silanization. For the present work, the effect of silanization temperature and time on the marching modulus of silica-filled rubber was evaluated. The correlations between these mixing parameters and their effect on the factors that have a strong relation with marching modulus intensity (MMI) were investigated: the amount of bound rubber, the filler flocculation rate (FFR), and the filler–polymer coupling rate (CR). The MMI was monitored by measuring the vulcanization rheograms using a rubber process analyzer (RPA) at small (approximately 7%) and large (approximately 42%) strain in order to discriminate the effects of filler–filler and filler–polymer interactions on the marching modulus of silica-filled rubber compounds. The results were interpreted via the correlation between these factors and their effect on the MMI. A higher temperature and a longer silanization time led to a better degree of silanization, in order of decreasing influence

    Dynamic Response and Molecular Chain Modifications Associated with Degradation during Mixing of Silica-Reinforced Natural Rubber Compounds

    Get PDF
    Mixing silica-reinforced rubber for tire tread compounds involves high shear forces and temperatures to obtain a sufficient degree of silanization. Natural Rubber (NR) is sensitive to mastication and chemical reactions, and thus, silica–NR mixing encounters both mechanical and thermal degradation. The present work investigates the degradation phenomena during the mixing of silica-reinforced NR compounds in-depth. The Mooney stress relaxation rates, the dynamic properties with frequency sweep, a novel characterization of branch formation on NR using Δδ values acc. Booij and van Gurp-Palmen plots, together, indicate two major competitive reactions taking place: chain scission or degradation and preliminary cross-linking or branch formation. For masticated pure NR and gum compounds, the viscous responses increase, and the changes in all parameters indicate the dominance of chain scission with increasing dump temperature. It causes molecular weight decrease, broader molecular weight distribution, and branched structures. Different behavior is observed for silica-filled NR compounds in which both physical and chemical cross-links are promoted by silanization and coupling reactions. At high dump temperatures above 150 °C, the results indicate a significant increase in branching due to preliminary cross-linking. These molecular chain modifications that cause network heterogeneity deteriorate the mechanical properties of resulting vulcanizates

    Structural variation-associated expression changes are paralleled by chromatin architecture modifications.

    Get PDF
    Copy number variants (CNVs) influence the expression of genes that map not only within the rearrangement, but also to its flanks. To assess the possible mechanism(s) underlying this "neighboring effect", we compared intrachromosomal interactions and histone modifications in cell lines of patients affected by genomic disorders and control individuals. Using chromosome conformation capture (4C-seq), we observed that a set of genes flanking the Williams-Beuren Syndrome critical region (WBSCR) were often looping together. The newly identified interacting genes include AUTS2, mutations of which are associated with autism and intellectual disabilities. Deletion of the WBSCR disrupts the expression of this group of flanking genes, as well as long-range interactions between them and the rearranged interval. We also pinpointed concomitant changes in histone modifications between samples. We conclude that large genomic rearrangements can lead to chromatin conformation changes that extend far away from the structural variant, thereby possibly modulating expression globally and modifying the phenotype. GEO SERIES ACCESSION NUMBER: GSE33784, GSE33867

    Structural variation in the 3D genome

    No full text
    Structural and quantitative chromosomal rearrangements, collectively referred to as structural variation (SV), contribute to a large extent to the genetic diversity of the human genome and thus are of high relevance for cancer genetics, rare diseases and evolutionary genetics. Recent studies have shown that SVs can not only affect gene dosage but also modulate basic mechanisms of gene regulation. SVs can alter the copy number of regulatory elements or modify the 3D genome by disrupting higher-order chromatin organization such as topologically associating domains. As a result of these position effects, SVs can influence the expression of genes distant from the SV breakpoints, thereby causing disease. The impact of SVs on the 3D genome and on gene expression regulation has to be considered when interpreting the pathogenic potential of these variant types
    corecore