Wind and solar powered turbine

A power generating station having a generator driven by solar heat assisted ambient wind is described. A first plurality of radially extendng air passages direct ambient wind to a radial flow wind turbine disposed in a centrally located opening in a substantially disc-shaped structure. A solar radiation collecting surface having black bodies is disposed above the fist plurality of air passages and in communication with a second plurality of radial air passages. A cover plate enclosing the second plurality of radial air passages is transparent so as to permit solar radiation to effectively reach the black bodies. The second plurality of air passages direct ambient wind and thermal updrafts generated by the black bodies to an axial flow turbine. The rotating shaft of the turbines drive the generator. The solar and wind drien power generating system operates in electrical cogeneration mode with a fuel powered prime mover

Fundamental study of transpiration cooling

Isothermal and non-isothermal pressure drop data and heat transfer data generated on porous 304L stainless steel wire forms, sintered spherical stainless steel powder, and sintered spherical OFHC copper powder are reported and correlated. Pressure drop data was collected over a temperature range from 500 R to 2000 R and heat transfer data collected over a heat flux range from 5 to 15 BTU/in2/sec. It was found that flow data could be correlated independently of transpirant temperature and type (i.e., H2, N2). It was also found that no simple relation between heat transfer coefficient and specimen porosity was obtainable

The stability of drop shapes for translation at zero Reynolds number through a quiescent fluid

Boundary-integral calculations are used to investigate the evolution of the shape of an initially nonspherical drop that translates at zero Reynolds through a quiescent, unbounded fluid. For finite capillary numbers, it is shown that the drop reverts to a sphere, provided the initial deformation is not too large. However, drops that are initially deformed to a greater extent are shown to deform continuously, forming an elongated shape with a tail when initially prolate, and a flattened shape with a cavity at the rear when initially oblate. The critical degree of deformation decreases as the capillary number increases and appears to be consistent with the results of Kojima et al. [Phys. Fluids 27, 19 (1984)], who showed that the spherical drop is unstable to infinitesimal disturbances in the limit Ca=∞

Parts verification for multi-level-dependent demand manufacturing systems: a recognition and classification structure

This research has developed and implemented a part recognition and classification structure to execute parts verification in a multi-level dependent demand manufacturing system. The part recognition algorithm enables the parent and child relationship between parts to be recognised in a finite-capacitated manufacturing system. This algorithm was developed using SIMAN simulation language and implemented in a multi-level dependent demand manufacturing simulation model. The part classification structure enables the modelling of a multi-level dependent demand manufacturing between parts to be carried out effectively. The part classification structure was programmed using Visual Basic Application (VBA) and was integrated to the work-to-list generated from a simulated MRP model. This part classification structure was then implemented in the multi-level dependent demand manufacturing simulation model. Two stages of implementation, namely parameterisation and execution, of the part recognition and classification structure were carried out. A real case study was used and five detail steps of execution were processed. Simulation experiments and MRP were run to verify and validate the part recognition and classification structure. The results led to the conclusion that implementation of the recognition and classification structure has effectively verified the correct parts and sub-assemblies used for the correct product and order. No parts and sub-assemblies shortages were found, and the quantity required was produced. The scheduled release for some orders was delayed due to overload of the required resources. When the loading is normal, all scheduled release timing is adhered to. The recognition and classification structure has a robust design; hence it can be easily adapted to new systems parameter to study a different or more complex case

Electronic states and optical properties of PbSe nanorods and nanowires

A theory of the electronic structure and excitonic absorption spectra of PbS and PbSe nanowires and nanorods in the framework of a four-band effective mass model is presented. Calculations conducted for PbSe show that dielectric contrast dramatically strengthens the exciton binding in narrow nanowires and nanorods. However, the self-interaction energies of the electron and hole nearly cancel the Coulomb binding, and as a result the optical absorption spectra are practically unaffected by the strong dielectric contrast between PbSe and the surrounding medium. Measurements of the size-dependent absorption spectra of colloidal PbSe nanorods are also presented. Using room-temperature energy-band parameters extracted from the optical spectra of spherical PbSe nanocrystals, the theory provides good quantitative agreement with the measured spectra.Comment: 35 pages, 12 figure

Not All SLAPs Are Created Equal: A Comparison of Patients with Planned and Incidental SLAP Repair Procedures

Background. Epidemiological studies have shown a progressive increase in the rate of superior labrum anterior-posterior (SLAP) repair surgery after the year 2000. However, it is not clear whether this is due to increased recognition of isolated SLAP tears or increased SLAP repair performed secondarily during arthroscopy for other purposes. Hypothesis/Purpose. We hypothesized that both isolated SLAP repair and secondary SLAP repair increased with time and that patient age influenced the pathway to SLAP diagnosis and surgery - such that younger patients were more likely to have isolated SLAP repair surgery after being diagnosed in clinic. Study Design. Descriptive epidemiology study. Methods. Data were obtained from the MarketScan database from 2003 to 2013. CPT and ICD-9 codes were used to identify SLAP surgery patients and concomitant procedures. The timing of SLAP diagnosis relative to surgery was used to determine whether the injury was recognized preoperatively. Results. 64,497 SLAP surgery patients were included. Preoperative SLAP diagnosis increased from 17.1% in 2003 to 44.6% in 2013. Patients diagnosed preoperatively were younger and had fewer concomitant procedures. Increasing age and concomitant rotator cuff tear (RCT) repair corresponded to lower odds of preoperative SLAP diagnosis. Discussion. Younger patients were more likely to have their SLAP tear diagnosed prior to surgery. Those diagnosed before surgery had fewer simultaneous procedures during their operations, suggesting that SLAP repair was more likely the primary operation. From 2003 to 2013, SLAP tears were increasingly recognized in the preoperative setting

Developing and applying a user-centered model for the design and implementation of information visualization tools

The objective of this paper is to show how approaches for user-centered information visualization design and development are being applied in the context of healthcare where users are not familiar with information visualization techniques. We base our design methods on user-centered frameworks in which 'prototyping' plays an important role in the process. We modify existing approaches to involve prototyping at an early stage of the process as the problem domain is assessed. We believe this to be essential, as it increases users' awareness of what information visualization techniques can offer them and that it enables users to participate more effectively in later stages of the design and development process. This also acts as a stimulus for engagement. The problem domain analysis stage of a pilot study using this approach is presented, in which techniques are being collaboratively developed with domain users from a healthcare institution. Our results suggest that this approach has engaged users, who are subsequently able to apply generic information visualization concepts to their domains and as a result are better equipped to take part in the subsequent collaborative design and development process

Statistical Basis for Predicting Technological Progress

Forecasting technological progress is of great interest to engineers, policy makers, and private investors. Several models have been proposed for predicting technological improvement, but how well do these models perform? An early hypothesis made by Theodore Wright in 1936 is that cost decreases as a power law of cumulative production. An alternative hypothesis is Moore's law, which can be generalized to say that technologies improve exponentially with time. Other alternatives were proposed by Goddard, Sinclair et al., and Nordhaus. These hypotheses have not previously been rigorously tested. Using a new database on the cost and production of 62 different technologies, which is the most expansive of its kind, we test the ability of six different postulated laws to predict future costs. Our approach involves hindcasting and developing a statistical model to rank the performance of the postulated laws. Wright's law produces the best forecasts, but Moore's law is not far behind. We discover a previously unobserved regularity that production tends to increase exponentially. A combination of an exponential decrease in cost and an exponential increase in production would make Moore's law and Wright's law indistinguishable, as originally pointed out by Sahal. We show for the first time that these regularities are observed in data to such a degree that the performance of these two laws is nearly tied. Our results show that technological progress is forecastable, with the square root of the logarithmic error growing linearly with the forecasting horizon at a typical rate of 2.5% per year. These results have implications for theories of technological change, and assessments of candidate technologies and policies for climate change mitigation

Glucose metabolism and oscillatory behavior of pancreatic islets

A variety of oscillations are observed in pancreatic islets.We establish a model, incorporating two oscillatory systems of different time scales: One is the well-known bursting model in pancreatic beta-cells and the other is the glucose-insulin feedback model which considers direct and indirect feedback of secreted insulin. These two are coupled to interact with each other in the combined model, and two basic assumptions are made on the basis of biological observations: The conductance g_{K(ATP)} for the ATP-dependent potassium current is a decreasing function of the glucose concentration whereas the insulin secretion rate is given by a function of the intracellular calcium concentration. Obtained via extensive numerical simulations are complex oscillations including clusters of bursts, slow and fast calcium oscillations, and so on. We also consider how the intracellular glucose concentration depends upon the extracellular glucose concentration, and examine the inhibitory effects of insulin.Comment: 11 pages, 16 figure