48,554 research outputs found
The Effect of Connecting-passage Diameter on the Performance of a Compression-ignition Engine with a Precombustion Chamber
Results of motoring tests are presented showing the effect of passage diameter on chamber and cylinder compression pressures, maximum pressure differences, and f.m.e.p. over a speed range from 300 to 1,750 r.p.m. Results of engine performance tests are presented which show the effect of passage diameter on m.e.p., explosion pressures, specific fuel consumption, and rates of pressure rise for a range of engine speeds from 500 to 1,500 r.p.m. The cylinder compression pressure, the maximum pressure difference, and the f.m.e.p. decreased rapidly as the passage diameter increased to 29/64 inch, whereas further increase in passage diameter effected only a slight change. The most suitable passage diameter for good engine performance and operating characteristics was 29/64 inch. Passage diameter became less critical with a decrease in engine speed. Therefore, the design should be based on maximum operating speed. Optimum performance and satisfactory combustion control could not be obtained by means of any single diameter of the connecting passage
Relative distributions of W's and Z's at low transverse momenta
Despite large uncertainties in the and transverse momentum
() distributions for q_T\lsim 10 GeV, the ratio of the distributions
varys little. The uncertainty in the ratio of to distributions is
on the order of a few percent, independent of the details of the
nonperturbative parameterization.Comment: 13 pages in revtex, 5 postscript figures available upon request,
UIOWA-94-0
Does the bracket-ligature combination affect the amount of orthodontic space closure over three months? A randomized controlled trial
OBJECTIVE: To investigate the effect of bracket-ligature combination on the amount of orthodontic space closure over three months. DESIGN: Randomized clinical trial with three parallel groups. SETTING: A hospital orthodontic department (Chesterfield Royal Hospital, UK). PARTICIPANTS: Forty-five patients requiring upper first premolar extractions. METHODS: Informed consent was obtained and participants were randomly allocated into one of three groups: (1) conventional pre-adjusted edgewise brackets and elastomeric ligatures; (2) conventional pre-adjusted edgewise brackets and Super Slick((R)) low friction elastomeric ligatures; (3) Damon 3MX((R)) passive self-ligating brackets. Space closure was undertaken on 0.019x0.025-inch stainless steel archwires with nickel-titanium coil springs. Participants were recalled at four weekly intervals. Upper alginate impressions were taken at each visit (maximum three). The primary outcome measure was the mean amount of space closure in a 3-month period. RESULTS: A one-way ANOVA was undertaken [dependent variable: mean space closure (mm); independent variable: group allocation]. The amount of space closure was very similar between the three groups (1 mm per 28 days); however, there was a wide variation in the rate of space closure between individuals. The differences in the amount of space closure over three months between the three groups was very small and non-significant (P = 0.718). CONCLUSION: The hypothesis that reducing friction by modifying the bracket/ligature interface increases the rate of space closure was not supported. The major determinant of orthodontic tooth movement is probably the individual patient response
The Effect of Clearance Distribution on the Performance of a Compression-ignition Engine with a Precombustion Chamber
The clearance distribution in a precombustion chamber cylinder head was varied so that for a constant compression ratio of 13.5 the spherical auxiliary chambers contained 20, 35, 50, and 70 per cent of the total clearance volume. Each chamber was connected to the cylinder by a single circular passage, flared at both ends, and of a cross-sectional area proportional to the chamber volume, thereby giving the same calculated air-flow velocity through each passage. Results of engine-performance tests are presented with variations of power, fuel consumption, explosion pressure, rate of pressure rise, ignition lag, heat loss to the cooling water, and motoring characteristics. For good performance the minimum auxiliary chamber volume, with the cylinder head design used, was 35 per cent of the total clearance volume; for larger volumes the performance improves but slightly. With the auxiliary chamber that contained 35 percent of the clearance volume there were obtained the lowest explosion pressures, medium rates of pressure rise, and slightly less than the maximum power. For all clearance distributions an increase in engine speed decreased the ignition lag in seconds and increased the rate of pressure rise
Perturbation Theory of Coulomb Gauge Yang-Mills Theory Within the First Order Formalism
Perturbative Coulomb gauge Yang-Mills theory within the first order formalism
is considered. Using a differential equation technique and dimensional
regularization, analytic results for both the ultraviolet divergent and finite
parts of the two-point functions at one-loop order are derived. It is shown how
the non-ultraviolet divergent parts of the results are finite at spacelike
momenta with kinematical singularities on the light-cone and subsequent branch
cuts extending into the timelike region.Comment: 23 pages, 6 figure
Complexation of Secondary Amides to Chromium(III): the X-Ray Structure of a Molecule with Two Modes of Monodentate Organic Amide Co-ordination
The X-ray crystal structure of the dimer [Cr{H(chba-Et)}(py)_2]_(2)·2py [H_(4)(chba-Et)= 1,2-bis(3,5-dichloro-2-hydroxybenzamido) ethane, py = pyridine] establishes, for the first time, the existence of N-co-ordination of an organic amide to Cr^III, the N-atom and carbonyl O-atom of two separate amide groups being co-ordinated to each Cr^III centre [Cr–N 2.030(6) and Cr–O 1.976(5)Å]; the potentially tetra-anionic chelating ligand leads to a variety of co-ordination modes
REGIONAL AND FUNCTIONAL DISAGGREGATION OF THE COTTON INDUSTRY IN A NATIONAL INPUT-OUTPUT MODEL
Crop Production/Industries,
A Balanced Diaphragm Type of Maximum Cylinder Pressure Indicator
A balanced diaphragm type of maximum cylinder pressure indicator was designed to give results consistent with engine operating conditions. The apparatus consists of a pressure element, a source of controlled high pressure and a neon lamp circuit. The pressure element, which is very compact, permits location of the diaphragm within 1/8 inch of the combustion chamber walls without water cooling. The neon lamp circuit used for indicating contact between the diaphragm and support facilitates the use of the apparatus with multicylinder engines
Not all the bots are created equal:the Ordering Turing Test for the labelling of bots in MMORPGs
This article contributes to the research on bots in Social Media. It takes as its starting point an emerging perspective which proposes that we should abandon the investigation of the Turing Test and the functional aspects of bots in favor of studying the authentic and cooperative relationship between humans and bots. Contrary to this view, this article argues that Turing Tests are one of the ways in which authentic relationships between humans and bots take place. To understand this, this article introduces the concept of Ordering Turing Tests: these are sort of Turing Tests proposed by social actors for purposes of achieving social order when bots produce deviant behavior. An Ordering Turing Test is method for labeling deviance, whereby social actors can use this test to tell apart rule-abiding humans and rule-breaking bots. Using examples from Massively Multiplayer Online Role-Playing Games, this article illustrates how Ordering Turing Tests are proposed and justified by players and service providers. Data for the research comes from scientific literature on Machine Learning proposed for the identification of bots and from game forums and other player produced paratexts from the case study of the game Runescape
The application of amino acid racemization in the acid soluble fraction of enamel to the estimation of the age of human teeth
Estimation of age-at-death for skeletonised forensic remains is one of the most significant problems in forensic anthropology. The majority of existing morphological and histological techniques are highly inaccurate, and show a bias towards underestimating the age of older individuals. One technique which has been successful in forensic age estimation is amino acid racemization in dentine. However, this method cannot be used on remains where the post-mortem interval is greater than 20 years. An alternative approach is to measure amino acid racemization in dental enamel, which is believed to be more resistant to change post-mortem. The extent of amino acid racemization in the acid soluble fraction of the enamel proteins was determined for modem known age teeth. A strong correlation was observed between the age of the tooth and the extent of racemization. No systematic bias in the direction of age estimation errors was detected. For the majority of teeth analyzed, the presence of dental caries did not affect the results obtained. In a minority of cases, carious teeth showed a higher level of racemization than would be expected given the age of the individual. These results indicate that amino acid racemization in enamel has the potential to be used in age estimation of skeletal remains. (C) 2007 Elsevier Ireland Ltd. All rights reserved
- …