Lost Apollo heat flow data suggest a different lunar bulk composition

Lunar surface heat flow values were measured on the Apollo missions between 1971 and 1977. However, the late-term data have been lost. We succeeded in archiving the data after March 1, 1976. We will introduce the new set of archived data

Detection of structure in asteroid analogue materials and Titan’s regolith by a landing spacecraft

We compare measurements made by two impact penetrometers of different sizes and with different tip shapes to further understand penetrometer design for performing pentrometry on an asteroid. To this end we re-visit the interpretation of data from the Huygens' penetrometer, ACC-E, that impacted Titan's surface. In addition we investigate the potential of a spacecraft fitted with a penetrometer to bounce using a test rig, built at The Open University (UK). Analysis of ACC-E laboratory data, obtained from impacts into ~4 mm diameter gravel, was found to produce an unusual decrease in resistance with depth (force-depth gradient) which was also seen in the Huygens' ACCE data from Titan and originally interpreted as a wet or moist sand. The downward trend could also be reproduced in a hybrid Discrete Element Model (DEM) if it was assumed that the near surface particles are more readily mobilised than those deeper in the target. With regard to penetrometer design penetration resistance was found to be sensitive to the ratio of particle to tip diameter. A clear trend was observed with a conical tip penetrometer, X-PEN, of decreasing force-depth gradients with increasing particle sizes most likely due to a transformation from a bulk displacement of material by the penetrating tip to more local interactions. ACC-E, which has a hemispherical tip, was found to produce a wider range of force-depth gradients than X-PEN, which had a conical tip, possibly due to difficulties dislodging jammed particles. Both penetrometers were able to determine particle diameter and mass after post-processing of the data. Laboratory simulations of landings with the test rig suggest that a large impact penetrometer under certain circumstances could absorb a significant amount of the elastic energy of the spacecraft possibly aiding landing. Alternatively a small impact penetrometer would allow the spacecraft to bounce freely on the surface to make a measurement at another location

Evidence for Recent Wet-Based Crater Glaciation in Tempe Terra, Mars.

[Introduction] Mars’ mid-latitudes host abundant putative debris-covered water-ice glaciers (viscous flow features; VFF). Eskers emerging from 110-150 Myr-old VFF in Phlegra Montes and Tempe Terra provide evidence for rare occurences of past, localized basal melting of their parent VFF, despite the cold climates of the late Amazonian (see this conf.). Eskers are sinuous ridges comprising glaciofluvial sediment deposited by meltwater flowing through tunnels within glacial ice. Here, we describe a population of sinuous ridges emerging from VFF in an unnamed ~45 km-diameter crater (38.47 N, 72.43 W) in Tempe Terra, ~600 km from the VFF-linked esker identified by Butcher et al. We consider two working hypotheses for the formation of the sinuous ridges; that they are either (1) eskers formed by melting of the glaciers from which they emerge, or (2) topographically inverted fluvial channels which formed prior to glaciation of the crater. We present observations from preliminary geomorphic mapping of the crater to start to test those hypotheses

MoonLITE – Technological feasibility of the penetrator concept

Introduction: While the surface missions to the Moon of the 1960s and 1970s achieved a great deal, scientifically a great deal was also left unresolved. The recent plethora of lunar missions (flown or proposed) reflects resurgence in interest in the Moon, not only in its own right, but also as a record of the formation of the Earth-Moon System and the interplanetary environment at 1 AU. Results from orbiter missions have indicated the possible presense of ice within permanently shaded craters at the lunar poles [1] – a situation that, if confirmed, will have profound impacts on lunar exploration

Computer modelling of a penetrator thermal sensor

The Philae lander is part of the Rosetta mission to investigate comet 67P/Churyumov-Gerasimenko. It will use a harpoon like device to anchor itself onto the surface. The anchor will perhaps reach depths of 1–2 m. In the anchor is a temperature sensor that will measure the boundary temperature as part of the MUPUS experiment. As the anchor attains thermal equilibrium with the comet ice it may be possible to extract the thermal properties of the surrounding ice, such as the thermal diffusivity, by using the temperature sensor data. The anchor is not an optimal shape for a thermal probe and application of analytical solutions to the heat equation is inappropriate. We prepare a numerical model to fit temperature sensor data and extract the thermal diffusivity. Penetrator probes mechanically compact the material immediately surrounding them as they enter the target. If the thermal properties, composition and dimensions of the penetrator are known, then the thermal properties of this pristine material may be recovered although this will be a challenging measurement. We report on investigations, using a numerical thermal model, to simulate a variety of scenarios that the anchor may encounter and how they will affect the measurement

Multi-Phase Sedment-Discharge Dynamics of Subglacial Drainage Recorded by a Glacier-Linked Esker in NW Tempe Terra, Mars

International audienceIntroduction: Our recent discoveries of eskers associated with 110-150 Myr old debris-covered glaciers in Phlegra Montes [1] and NW Tempe Terra [2], Mars, indicate that localised wet-based glaciation has occurred in at least two locations during the late Amazonian , despite cold climate conditions. Eskers are sedi-mentary ridges deposited by meltwater flowing through drainage tunnels within or beneath glaciers. In this study, we use new 3D measurements of the NW Tempe Terra esker (46.17 °N, 83.06 °W) to develop a conceptual model for the sediment-discharge dynamics of the esker-forming drainage episode(s). Methods: Following [3], we used a 2 m/pixel digital elevation model derived from High Resolution Imaging Science Experiment (HiRISE) images to measure ridge height (H) and width (W) every ~20 m along the esker. We exclude ridge portions obscured by the parent glacier (Fig 1), as well as transitions between morphological zones. Results: A scatterplot of the raw height and width measurements (Fig 2A) has multiple limbs which correspond to subzones of the esker with common morphological characteristics (Fig 1)

3D Morphometries of Eskers on Mars, and Comparisons to Eskers in Finland

International audienceIntroduction: We present new, high-resolution measurements of the 3D morphometries of eskers associated with debris-covered glaciers in the Phlegra Mon-tes [1] and NW Tempe Terra [2] regions of Mars' northern mid-latitudes. We compare them with the ancient south polar 'Dorsa Argentea' eskers on Mars [3], and first large database (n > 20,000) of 3D morphome-tries of terrestrial eskers, from SW Finland [4]. Eskers are ridges of glaciofluvial sediment deposited by meltwater flowing through tunnels within or beneath glaciers. They are vital tools for reconstructing the dynamics, extent, and environmental drivers of wet-based glaciation on Earth and Mars. For example, reconstructions of Mars' climate conditions at the Noa-chian-Hesperian transition [e.g., 5] have relied heavily upon insights from the Dorsa Argentea eskers [e.g., 3], which record basal melting of a large south polar ice sheet ~3.5 Ga. Morphometric studies of candidate eskers on Mars are vital both for testing hypotheses of their origins as eskers [e.g., 3], and for informing insights into the magnitude and dynamics of meltwater flows that formed them [e.g., 5-6]. Previously, such work has been limited by a lack of large-scale surveys of the 3D morphometries of eskers on Earth, to which the martian landforms can be compared. A new database comprising >20 000 measurements of 3D esker morphometries from SW Finland provides new opportunities for such-comparisons, which we exploit in this study [4]. Methods: We used 1-2 m/pixel digital elevation models generated from High Resolution Imaging Science Experiment (HiRISE) images to measure esker heights (H) and widths (W) from cross-sectional tran-sects spaced at 10 and 20 m intervals along the Phlegra Montes and NW Tempe Terra eskers, respectively (fol-lowing [3]). We calculated average slopes across cross-sectional transects (θ) as: tan −1 (H/0.5W). We classified transects into sharp-, multi-, and round-crested morphologies according to the scheme of [6]. The NW Tempe Terra esker comprises two 'stacked' esker ridges (see [7], this conference) which we treat separately in the present study. Storrar and Jones [4] obtained similar H, W, and θ measurements at 10 m intervals along ~70 km of Qua-ternary-aged eskers in SW Finland, using 2 m/pixel elevation data from airborne LiDAR