7,256 research outputs found
Stochastic Gravitational Wave Measurements with Bar Detectors: Dependence of Response on Detector Orientation
The response of a cross-correlation measurement to an isotropic stochastic
gravitational-wave background depends on the observing geometry via the overlap
reduction function. If one of the detectors being correlated is a resonant bar
whose orientation can be changed, the response to stochastic gravitational
waves can be modulated. I derive the general form of this modulation as a
function of azimuth, both in the zero-frequency limit and at arbitrary
frequencies. Comparisons are made between pairs of nearby detectors, such as
LIGO Livingston-ALLEGRO, Virgo-AURIGA, Virgo-NAUTILUS, and EXPLORER-AURIGA,
with which stochastic cross-correlation measurements are currently being
performed, planned, or considered.Comment: 17 pages, REVTeX (uses rcs, amsmath, hyperref, and graphicx style
files), 4 figures (8 eps image files
Physical parameters of the Cen X-3 system
Photographic spectra of Cen X-3 show that the primary star has a spectral type near 06.5 with weak, variable emission at wavelength 4640 and 4686. No orbital motion of the emission or absorption lines is detected; for the latter the upper limit is approximately + or - 50 km/s. Analysis of the available data indicates that the primary is a factor of 2-3 less massive than expected from normal evolutionary models while the X-ray source has a solar mass near 1.5
Develop and test fuel cell powered on-site integrated total energy systems: Phase 3, full-scale power plant development
A 25 cell stack of the 13 inch x 23 inch cell size (about 4kW) remains on test after 6000 hours, using simulated reformate fuel. A similar stack was previously shut down after 7000 hours on load. These tests were carried out for the purpose of assessing the durability of fuel cell stack components developed through the end of 1983. In light of the favorable results obtained, a 25kW stack that will contain 175 cells of the same size is being constructed using the same technology base. The components for the 25kW stack have been completed. A methanol steam reformer with a design output equivalent to 50kW has been constructed to serve as a hydrogen generator for the 25kW stack. This reformer and the balance of the fuel processing sub system are currently being tested and debugged. The stack technology development program focused on cost reduction in bipolar plates, nonmetallic cooling plates, and current collecting plates; more stable cathode catalyst support materials; more corrosion resistant metal hardware; and shutdown/start up tolerance
Develop and test fuel cell powered on-site integrated total energy systems
On-going testing of an 11 cell, 10.7 in. x 14 in. stack (about 1 kW) reached 2600 hours on steady load. Nonmetallic cooling plates and an automated electrolyte replenishment system continued to perform well. A 10 cell, 10.7 in. x 14 in. stack was constructed with a modified electrolyte matrix configuration for the purpose of reducing cell IR loss. The desired effect was achieved, but the general cell performance level was irregular. Evaluation is continuing. Preparations for a long term 25 cell, 13 in. x 23 in. test stack (about 4 kW) approached completion. Start up in early May 1984 is expected
Develop and test fuel cell powered on-site integrated total energy system
Test results are presented for a 24 cell, two sq ft (4kW) stack. This stack is a precursor to a 25kW stack that is a key milestone. Results are discussed in terms of cell performance, electrolyte management, thermal management, and reactant gas manifolding. The results obtained in preliminary testing of a 50kW methanol processing subsystem are discussed. Subcontracting activities involving application analysis for fuel cell on site integrated energy systems are updated
Searching for Galactic White Dwarf Binaries in Mock LISA Data using an F-Statistic Template Bank
We describe an F-statistic search for continuous gravitational waves from
galactic white-dwarf binaries in simulated LISA Data. Our search method employs
a hierarchical template-grid based exploration of the parameter space. In the
first stage, candidate sources are identified in searches using different
simulated laser signal combinations (known as TDI variables). Since each source
generates a primary maximum near its true "Doppler parameters" (intrinsic
frequency and sky position) as well as numerous secondary maxima of the
F-statistic in Doppler parameter space, a search for multiple sources needs to
distinguish between true signals and secondary maxima associated with other,
"louder" signals. Our method does this by applying a coincidence test to reject
candidates which are not found at nearby parameter space positions in searches
using each of the three TDI variables. For signals surviving the coincidence
test, we perform a fully coherent search over a refined parameter grid to
provide an accurate parameter estimation for the final candidates. Suitably
tuned, the pipeline is able to extract 1989 true signals with only 5 false
alarms. The use of the rigid adiabatic approximation allows recovery of signal
parameters with errors comparable to statistical expectations, although there
is still some systematic excess with respect to statistical errors expected
from Gaussian noise. An experimental iterative pipeline with seven rounds of
signal subtraction and re-analysis of the residuals allows us to increase the
number of signals recovered to a total of 3419 with 29 false alarms.Comment: 29 pages, 11 figures; submitted to Classical and Quantum Gravit
Continuous-flow laboratory simulation of stream water quality changes downstream of an untreated wastewater discharge.
In regions of the world with poor provision of wastewater treatment, raw sewage
is often discharged directly into surface waters. This paper describes an
experimental evaluation of the fate of two organic chemicals under these
conditions using an artificial channel cascade fed with a mix of settled sewage
and river water at its upstream end and operated under continuous steady-state
conditions. The experiments underpin an environmental risk assessment
methodology based on the idea of an “impact zone” (IZ) – the zone downstream of
wastewater emission in which water quality is severely impaired by high
concentrations of unionised ammonia, nitrite and biochemical oxygen demand
(BOD). Radiolabelled dodecane-6-benzene sulphonate (DOBS) and aniline
hydrochloride were used as the model chemical and reference compound
respectively. Rapid changes in 14C counts were observed with flow-time for both
these materials. These changes were most likely to be due to complete
mineralisation. A dissipation half-life of approximately 7.1 h was observed for
the 14C label with DOBS. The end of the IZ was defined as the point at which the
concentration of both unionised ammonia and nitrite fell below their respective
predicted no-effect concentrations for salmonids. At these points in the
cascade, approximately 83 and 90% of the initial concentration of 14C had been
removed from the water column, respectively. A simple model of mineral nitrogen
transformations based on Michaelis–Menten kinetics was fitted to observed
concentrations of NH4, NO2 and NO3. The cascade is intended to provide a
confirmatory methodology for assessing the ecological risks of chemicals under
direct discharge co
Develop and test fuel cell powered on site integrated total energy sysems: Phase 3: Full-scale power plant development
A 25-cell stack of the 13 inch x 23 inch cell size (about 4kW) remains on test after 8300 hours, using simulated reformate fuel. A similar stack was previously shut down after 7000 hours on load. These tests have been carried out for the purpose of assessing the durability of fuel cell stack components developed through the end of 1983. A 25kW stack containing 175 cells of the same size and utilizing a technology base representative of the 25-cell stacks has been constructed and is undergoing initial testing. A third 4kW stack is being prepared, and this stack will incorporate several new technology features
An Economic Evaluation of Irish Salmon Fishing General Summary of Results. ESRI Memorandum Series No. 99 1974
The purpose of the study was to investigate the economies of salmon fishing in Ireland. Essentially, it set out to answer the question "how valuable was the Irish salmon industry to the economy in 1970?" In order to answer this
question, the study tried to evaluate the economic impact of angling and commercial fishing on the various districts, determine the capacity of the industry for future development and provide information to assist in the more effective marketing of salmon and sea-trout angling. Although the survey was confined to 1970, its findings may be updated for subsequent years by means of the regularly published data on catches and numbers of licences, and by appropriate price indices
An Economic Evaluation of Irish Salmon Fishing, II: The Irish Anglers. General Research Series Paper No. 75, June 1974
The first part of the study, which dealt with salmon
anglers from outside the Republic, has already been completed and the results
published [i]. The terms of reference of the study together with some background
information were given in the latter publication. This second part is
concerned with Irish salmon anglers and particularly with assessing the extent
and regional distribution of the economic effects of their activities. In both
these papers, we attempt to find out what Sort of peoplethe ang!ers are; where
and how Often they fish, and, particularly, how much they spend and where this
expenditure takes place. The concluding part of the study will deal with commercial
fishermen and fishery operators, and in that paper we also hope to
amalgamate our information on angling and on commercial fishing into a
comprehensive picture of Irish salmon fishing
- …