Eigenvalue Placement and Stabilization by Constrained Optimization

A pole placement algorithm is proposed which uses constrained nonlinear optimization techniques on a finite dimensional model of a linear n degree of freedom system. Low order feedback control is assumed where r poles may be assigned; r being the rank of the sensor coefficient matrix. It is shown that by combining feedback control theory methods with optimization techniques, one can ensure the stability characteristics of a system, and can alter its transient response

On damping mechanisms in beams

A partial differential equation model of a cantilevered beam with a tip mass at its free end is used to study damping in a composite. Four separate damping mechanisms consisting of air damping, strain rate damping, spatial hysteresis and time hysteresis are considered experimentally. Dynamic tests were performed to produce time histories. The time history data is then used along with an approximate model to form a sequence of least squares problems. The solution of the least squares problem yields the estimated damping coefficients. The resulting experimentally determined analytical model is compared with the time histories via numerical simulation of the dynamic response. The procedure suggested here is compared with a standard modal damping ratio model commonly used in experimental modal analysis

Candidate proof mass actuator control laws for the vibration suppression of a frame

The vibration of an experimental flexible space truss is controlled with internal control forces produced by several proof mass actuators. Four candidate control law strategies are evaluated in terms of performance and robustness. These control laws are experimentally implemented on a quasi free-free planar truss. Sensor and actuator dynamics are included in the model such that the final closed loop is self-equilibrated. The first two control laws considered are based on direct output feedback and consist of tuning the actuator feedback gains to the lowest mode intended to receive damping. The first method feeds back only the position and velocity of the proof mass relative to the structure; this results in a traditional vibration absorber. The second method includes the same feedback paths as the first plus feedback of the local structural velocity. The third law is designed with robust H infinity control theory. The fourth strategy is an active implementation of a viscous damper, where the actuator is configured to provide a bending moment at two points on the structure. The vibration control system is then evaluated in terms of how it would benefit the space structure's position control system

Static and dynamic characteristics of a piezoceramic strut

The experimental study of a piezoceramic active truss is presented. This active strut is unique in that the piezoceramic configurations allow the stroke length of the strut not to be dependent on the piezoceramic material's expansion range but on the deflection range of the piezoceramic bender segment. A finite element model of a piezoceramic strut segment was constructed. Piezoceramic actuation was simulated using thermally induced strains. This model yielded information on the stiffness and force range of a bender element. The static and dynamic properties of the strut were identified experimentally. Feedback control was used to vary the stiffness of the strut. The experimentally verified model was used to explore implementation possibilities of the strut

Central Policies for Local Debt: The Case of Teacher Pensions

The recent debt crises in New York City and Cleveland, the deterioration of public infra-structures in certain of our states and larger cities, and the occasional bankruptcy of smaller pension plans suggest that not all of local finance stands on a sound fiscal base. This paper examines the trends in funding for one form of state and local government debt--teacher pensions underfundings -- and asks what a central government might do to check any unwanted growth in these liabilities. The analysis concludes (i) that this form of state-local debt is sizeable and growing, (ii) that state and local governments have an implicit pay-as-you-go bias in pension financing which encourages the growth of debt, but (iii) central government benefit and funding regulations or debt relief policies can slow, or even reverse, that growth.

Vibration suppression and slewing control of a flexible structure

Examined here are the effects of motor dynamics and secondary piezoceramic actuators on vibration suppression during the slewing of flexible structures. The approach focuses on the interaction between the structure, the actuators, and the choice of control law. The results presented here are all simulated, but are based on experimentally determined parameters for the motor, structure, piezoceramic actuators, and piezofilm sensors. The simulation results clearly illustrate that the choice of motor inertia relative to beam inertia makes a critical difference in the performance of the system. In addition, the use of secondary piezoelectric actuators reduces the load requirements on the motor and also reduces the overshoot of the tip deflection. The structures considered here are a beam and a frame. The majority of results are based on a Euler Bernoulli beam model. The slewing frame introduces substantial torsional modes and a more realistic model. The slewing frame results are incomplete and represent work in progress

Control of a flexible planar truss using proof mass actuators

A flexible structure was modeled and actively controlled by using a single space realizable linear proof mass actuator. The NASA/UVA/UB actuator was attached to a flexible planar truss structure at an optimal location and it was considered as both passive and active device. The placement of the actuator was specified by examining the eigenvalues of the modified model that included the actuator dynamics, and the frequency response functions of the modified system. The electronic stiffness of the actuator was specified, such that the proof mass actuator system was tuned to the fourth structural mode of the truss by using traditional vibration absorber design. The active control law was limited to velocity feedback by integrating of the signals of two accelerometers attached to the structure. The two lower modes of the closed-loop structure were placed further in the LHS of the complex plane. The theoretically predicted passive and active control law was experimentally verified

Comparison of acoustic and strain gauge techniques for crack closure measurements

A quantitative study on the systems performances of the COD gauge and the acoustic transmission techniques to elastic deformation of part-through crack and compact tension specimens has been conducted. It is shown that the two instruments measure two completely different quantities: The COD gauge yields information on the length change of the specimen whereas the acoustic technique is sensitive directly to the amount of contract area between two surfaces, interfering with the acoustic signal. In another series of experiments, compression tests on parts with specifically prepared surfaces were performed so that the surface contact area could be correlated with the transmitted acoustic signal, as well as the acoustic with the COD gauge signal. A linear relation between contact area and COD gauge signal was obtained until full contact had been established

Controlling flexible structures with second order actuator dynamics

The control of flexible structures for those systems with actuators that are modeled by second order dynamics is examined. Two modeling approaches are investigated. First a stability and performance analysis is performed using a low order finite dimensional model of the structure. Secondly, a continuum model of the flexible structure to be controlled, coupled with lumped parameter second order dynamic models of the actuators performing the control is used. This model is appropriate in the modeling of the control of a flexible panel by proof-mass actuators as well as other beam, plate and shell like structural numbers. The model is verified with experimental measurements

Artificial piezoelectric grass for energy harvesting from turbulence-induced vibration

The primary objective of this research is to develop a deploy-and-forget energy harvesting device for use in low-velocity, highly turbulent fluid flow environments i.e. streams or ventilation systems. The work presented here focuses on a novel, lightweight, highly robust, energy harvester design referred to as piezoelectric grass . This biologically inspired design consists of an array of cantilevers, each constructed with piezoelectric material. When exposed to proper turbulent flow conditions, these cantilevers experience vigorous vibrations. Preliminary results have shown that a small array of piezoelectric grass was able to produce up to 1.0 mW per cantilever in high-intensity turbulent flow having a mean velocity of 11.5 m s −1 . According to the literature, this is among the highest output achieved using similar harvesting methods. A distributed parameter model for energy harvesting from turbulence-induced vibration will be introduced and experimentally validated. This model is generalized for the case of a single cantilever in turbulent cross-flow. Two high-sensitivity pressure probes were needed to perform spectral measurements within various turbulent flows. The design and performance of these probes along with calibration and measurement techniques will be discussed.Peer Reviewedhttp://deepblue.lib.umich.edu/bitstream/2027.42/98616/1/0964-1726_21_10_105024.pd