195 research outputs found

    Improved photovoltaic devices, using transparent contacts

    Get PDF
    Transparent conducting coating is applied to narrow pn junction surface to provide ohmic contact for majority carrier flow. Coating can be made thick to prevent series resistance problem

    Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures, phase 2

    Get PDF
    Crystal growth procedures, fabrication techniques, and theoretical analysis were developed in order to make GaAlAs-GaAs solar cell structures which exhibit high performance at air mass 0 illumination and high temperature conditions

    The optimization of Ga (1-x)Al (x)As-GaAs solar cells for air mass zero operation and a study of Ga (1-x)Al (x)As-GaAs solar cells at high temperatures, phase 1

    Get PDF
    The three types of solar cells investigated were: (1) one consisting of a nGaAs substrate, a Zn doped pGaAs region, and a Zn doped Ga(1-x)Al(x)As layer, (2) one consisting of an nGaAs substrate, a Ge doped pGaAs region, and a pGa(1-x)Al(x)As upper layer, and (3) one consisting of an n+GaAs substrate, an nGa(1-x)Al(X)As region, a pGa(1-x)Bl(X) As region, and a pGa(1-y)Al(y)As upper layer. In all three cases, the upper alloy layer is thin and of high Al composition in order to obtain high spectral response over the widest possible range of photon energies. Spectral response, capacitance-voltage, current-voltage, diffusion length, sunlight (or the equivalent)-efficiency, and efficiency-temperature measurements were made as a function of device parameters in order to analyze and optimize the solar cell behavior

    Optimization of solar cells for air mass zero operation and study of solar cells at high temperatures, phase 4

    Get PDF
    The Pd contact to GaAs was studied using backscattering, Auger analysis, and sheet resistance measurements. Several metallurgical phases were present at low temperatures, but PdGa was the dominant phase in samples annealed at 500 C. Ti/Pd/Ag contacts appeared to have the lowest contact resistance. Etchback epitaxy (EBE) was compared to saturated melt epitaxy (SME) method of growing liquid phase epitaxial layers. The SME method resulted in a lower density of Ga microdroplets in the grown layer, although the best solar cells were made by the EBE method. Photoluminescence was developed as a tool for contactless analysis of GaAs cells. Efficiencies of over 8 percent were measured at 250 C

    Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures, phase 3

    Get PDF
    The etch-back epitaxy process is described for producing thin, graded composition GaAlAs layers. The palladium-aluminum contact system is discussed along with its associated problems. Recent solar cell results under simulated air mass zero light and at elevated temperatures are reported and the growth of thin polycrystalline GaAs films on foreign substrates is developed

    Optimization of solar cells for air mass zero operation and a study of solar cells at high temperatures

    Get PDF
    The power to weight ratio of GaAs cells can be reduced by fabricating devices using thin GaAs films on low density substrate materials (silicon, glass, plastics). A graphoepitaxy technique was developed which uses fine geometric patterns in the substrate to affect growth. Initial substrates were processed by etching 25 microns deep grooves into 100 oriented wafers; fine-grained polycrystalline GaAs layers 25-50 microns thick were then deposited on these and recrystallization was performed, heating the substrates to above the GaAs melting point in ASH3 atmosphere, resulting in large grain regrowth oriented along the groove dimensions. Experiments with smaller groove depths and spacings were initially encouraging; single large GaAs grains would totally cover one and often two groove fields of 14 groove each spanning several hundred microns. Dielectric coatings on the grooved substrates were also used to modify the growth

    Crystalline structure and orientation of gold clusters grown in preformed nanometer-sized pits

    Get PDF
    Abstract Gold clusters were produced by condensing evaporated gold in nanometer-sized preformed pits on the surface of highly Ž . oriented pyrolytic graphite HOPG . The height of the clusters was 6.7 " 0.7 nm as measured with scanning tunneling microscopy in ultrahigh vacuum, the lateral width was 10.1 " 1.9 nm as determined with transmission electron microscopy Ž . TEM . Using TEM for electron diffraction, we obtained information on the crystalline structure of the clusters. The Ž . intensity of the observed diffraction rings shows the preferential orientation of the clusters with the 111 plane of the gold Ž . lattice parallel to the 0001 surface of HOPG. This was compared to the diffraction pattern of gold clusters produced in the gas phase by inert-gas evaporation and deposited on a flat HOPG surface at room temperature as complete units which showed no preferential orientation. The directional alignment in the surface plane as it is described in the literature for larger gold crystallites grown on a flat HOPG surface is not observed for the nanometer-sized clusters grown in pits

    Tunable variation of optical properties of polymer capped gold nanoparticles

    Full text link
    Optical properties of polymer capped gold nanoparticles of various sizes (diameter 3-6 nm) have been studied. We present a new scheme to extract size dependent variation of total dielectric function of gold nanoparticles from measured UV-Vis absorption data. The new scheme can also be used, in principle, for other related systems as well. We show how quantum effect, surface atomic co - ordination and polymer - nanoparticle interface morphology leads to a systematic variation in inter band part of the dielectric function of gold nanoparticles, obtained from the analysis using our new scheme. Careful analysis enables identification of the possible changes to the electronic band structure in such nanoparticles.Comment: 13 pages,7 figures, 1 tabl

    Fully Gapped Single-Particle Excitations in the Lightly Doped Cuprates

    Full text link
    The low-energy excitations of the lightly doped cuprates were studied by angle-resolved photoemission spectroscopy. A finite gap was measured over the entire Brillouin zone, including along the d_{x^2 - y^2} nodal line. This effect was observed to be generic to the normal states of numerous cuprates, including hole-doped La_{2-x}Sr_{x}CuO_{4} and Ca_{2-x}Na_{x}CuO_{2}Cl_{2} and electron-doped Nd_{2-x}Ce_{x}CuO_{4}. In all compounds, the gap appears to close with increasing carrier doping. We consider various scenarios to explain our results, including the possible effects of chemical disorder, electronic inhomogeneity, and a competing phase.Comment: To appear in Phys. Rev.

    Deterministic polarization chaos from a laser diode

    Full text link
    Fifty years after the invention of the laser diode and fourty years after the report of the butterfly effect - i.e. the unpredictability of deterministic chaos, it is said that a laser diode behaves like a damped nonlinear oscillator. Hence no chaos can be generated unless with additional forcing or parameter modulation. Here we report the first counter-example of a free-running laser diode generating chaos. The underlying physics is a nonlinear coupling between two elliptically polarized modes in a vertical-cavity surface-emitting laser. We identify chaos in experimental time-series and show theoretically the bifurcations leading to single- and double-scroll attractors with characteristics similar to Lorenz chaos. The reported polarization chaos resembles at first sight a noise-driven mode hopping but shows opposite statistical properties. Our findings open up new research areas that combine the high speed performances of microcavity lasers with controllable and integrated sources of optical chaos.Comment: 13 pages, 5 figure
    corecore