Studying the thermo-gas-dynamic process in a muzzle brake compensator

To reduce the recoil and improve the stability of small arms, a muzzle brake compensator is attached to the muzzle of the barrel. This device uses the kinetic energy of the powder gas escaping from the bore after the bullet is fired. In this paper, the authors present the determination of the thermo-gas-dynamic model of the operation of a muzzle brake compensator and an example of calculating this type of muzzle device for the AK assault rifle using 7.62x39 mm ammunition. The results of the calculation allowed for obtaining the parameters of the powder gas flow in the process of flowing out of the muzzle device, as well as the change in the momentum of the powder gas's impact on the muzzle device. The model proposed in the article provides the basis for a quantitative evaluation of the effectiveness of using the muzzle device in stabilizing infantry weapons when firing

Kinetics of Organic Biodegradation and Biogas Production in the Pilot-Scale Moving Bed Biofilm Reactor (MBBR) for Piggery Wastewater Treatment

In this research, the kinetics of COD biodegradation and biogas production in a moving bed biofilm reactor (MBBR) at pilot scale (10 m3) for piggery wastewater treatment were investigated. Polyethylene (PE) was used as a carrying material, with organic loading rates (OLRs) of 10, 15, and 18 kgCOD/m3 day in accordance to hydraulic retention times (HRTs) of 0.56, 0.37, and 0.3 day. The results showed that a high COD removal efficiency was obtained in the range of 68–78% with the influent COD of 5.2–5.8 g/L at all 3 HRTs. About COD degradation kinetics, in comparison to the first- and second-order kinetics and the Monod model, Stover–Kincannon model showed the best fit with R2 0.98 and a saturation value constant (KB) and a maximum utilization rate (Umax) of 52.40 g/L day and 82.65 g/L day, respectively. The first- and second-order kinetics with all 3 HRTs and Monod model with the HRT of 0.56 day also obtained high R2 values. Therefore, these kinetics and models can be further considered to be used for predicting the kinetic characteristics of the MBBR system in piggery wastewater treatment process. The result of a 6-month operation of the MBBR was that biogas production was mostly in the operating period of days 17 to 80, around 0.2 to 0.3 and 0.15–0.20 L/gCODconverted, respectively, and then reduction at an OLR of 18 kgCOD/m3. After the start-up stage, day 35 biogas cumulative volume fluctuated from 20 to 30 m3/day and reached approximately 3500 m3 for 178 days during the whole digestive process. Methane is accounted for about 65–70% of biogas with concentration around 400 mg/L

Three-Photon Absorption Induced Photoluminescence in Organo-Lead Mixed Halide Perovskites

International audienc

Simulation dataset of thermal and epithermal neutron self-shielding correction factors for 186W(n,γ)187W reaction rate experiments using tungsten foil targets

In the experiments of neutron interaction with research samples, the incident neutron energy spectrum, distribution inside the irradiating sample volume, is affected by the unexpected neutron self-shielding effects. The nature of these effects is due to the formation and thickness of the irradiating sample, which significantly causes neutron self-absorption and multiple scattering inside the sample volume. The datasets presented in this article showed the thermal (Gth) and epithermal (Gepi) neutron self-shielding correction factors for the 186W(n,γ)187W neutron capture reaction rate in irradiating tungsten (W) foil samples with different thicknesses. The simulations were performed for three models of surface neutron source's geometries and relative orientations of the irradiating foil samples of isotropic cylinder surface neutron source with foil sample along to the center line, isotropic cylinder neutron source with foil sample flat to the center line, and isotropic spherical neutron source with foil sample placed at the center point. The range of sample thicknesses was from 10 µm to 2.5 mm. The uncertainties for each data point are also reported in the data table, making it more convenient for reuse in related experiments or evaluations

Enhanced Photocatalytic Performance of Nitrogen-Doped TiO₂ Nanotube Arrays Using a Simple Annealing Process

Nitrogen-doped TiO2 nanotube arrays (N-TNAs) were successfully fabricated by a simple thermal annealing process in ambient N2 gas at 450 °C for 3 h. TNAs with modified morphologies were prepared by a two-step anodization using an aqueous NH4F/ethylene glycol solution. The N-doping concentration (0–9.47 at %) can be varied by controlling N2 gas flow rates between 0 and 500 cc/min during the annealing process. Photocatalytic performance of as-prepared TNAs and N-TNAs was studied by monitoring the methylene blue degradation under visible light (λ ≥ 400 nm) illumination at 120 mW·cm−2. N-TNAs exhibited appreciably enhanced photocatalytic activity as compared to TNAs. The reaction rate constant for N-TNAs (9.47 at % N) reached 0.26 h−1, which was a 125% improvement over that of TNAs (0.115 h−1). The significant enhanced photocatalytic activity of N-TNAs over TNAs is attributed to the synergistic effects of (1) a reduced band gap associated with the introduction of N-doping states to serve as carrier reservoir, and (2) a reduced electron‒hole recombination rate

In the interest of public safety: rapid response to the COVID-19 epidemic in Vietnam

We describe the status of the COVID-19 epidemic in Vietnam, major response successes, factors that prompted implementation of certain public health actions, and the impact of these actions. In addition, information for three case studies is reported, with crucial learnings to inform future response. Findings from this study suggest that as early as 20 January 2020, Vietnam held a national risk assessment, established a national COVID-19 Response Plan and Technical Treatment and Care Guidelines, and prepared public health laboratories to accurately diagnose cases and hospitals to effectively treat patients. The first COVID-19 case was detected on 23 January. As of 30 September, there had been three waves of the COVID-19 epidemic totalling 1095 cases, and resulting in 35 deaths all among people with underlying health conditions. Evidence of potential transmission of SARS-CoV-2 from a commercial passenger flight inbound to Vietnam was reported. This study also highlights the importance of early technical preparedness, strong political commitment, multisectoral and multilevel efforts, increased resourcing and coordination towards an effective COVID-19 response. Controlling outbreaks in settings, such as crowded public places (bars and hospitals), within certain villages and over cities, required early detection, aggressive trace-test-quarantine efforts, a geographically extensive lockdown area and an adoption of several non-pharmaceutical interventions. Many low-income and middle-income countries have experienced their second or third wave of the COVID-19 epidemic, and they can learn from Vietnam’s response across the three epidemic waves. Swift governmental action, strict border control measures, effective communication of health promotion measures, widespread community engagement, expanded testing capacity and effective social measures to slow the spread of SARS-CoV-2, are highly important in these locations

Facile Synthesis of 4-Oxo-4<i>H</i>-quinolizine-2-carboxamide Derivatives

<div><p></p><p>A facile synthetic method for the construction of 2-substituted-4-oxo-4H-quinolizine based core structure has been successfully developed. The synthesis made use of a one pot Stobbe condensation followed by cyclisation starting from the commercially available 2-pyridinecarbaldehyde. The structure of the formed 4-oxo-4H-quinolizine-2-carboxylate was fully confirmed by MS, ¹H NMR, ¹³C NMR, COSY, HMBC and HSQC spectra. The ethyl carboxylate moiety was then further functionalized via direct aminolysis by a range of amines to afford the corresponding 4-oxo-4H-quinolizine-2-carboxamides <b>4a-i</b> in moderate to good yields.</p></div