Comment on "A note on the construction of the Ermakov-Lewis invariant"

We show that the basic results on the paper referred in the title [J. Phys. A: Math. Gen. v. 35 (2002) 5333-5345], concerning the derivation of the Ermakov invariant from Noether symmetry methods, are not new

Study on integration of silver-zinc battery improvements Interim technical report, 1 Jan. - 30 Jun. 1970

Components and single cell design for five cell silver zinc batter

Study on integration of silver-zinc battery improvements Interim technical report, 1 Mar. 1969 - 31 Dec. 1969

Research and development in silver zinc batteries for aerospace us

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 2: Stage performance

The aerodynamic performance of the compressor-drive turbine of the DOE upgraded gas turbine engine was determined in low temperature air. The as-received cast rotor blading had a significantly thicker profile than design and a fairly rough surface finish. Because of these blading imperfections a series of stage tests with modified rotors were made. These included the as-cast rotor, a reduced-roughness rotor, and a rotor with blades thinned to near design. Significant performance changes were measured. Tests were also made to determine the effect of Reynolds number on the turbine performance. Comparisons are made between this turbine and the compressor-drive turbine of the DOE baseline gas turbine engine

The effect of rotor blade thickness and surface finish on the performance of a small axial flow turbine

An experimental investigation was conducted to determine the effect of blade profile inaccuracies and surface finish on the aerodynamic performance of a 11.13 cm tip diameter turbine. The as-received cast rotor blades had a significantly thicker profile than the design intent and a fairly rough surface finish. Stage test results showed an increase of one point in efficieny by smoothing the surface finish and another three points by thinning the blade profiles to near the design profile. Most of the performance gain between the as-cast thick and the thinned rotor blades both with the same surface finish, was attributed to reduced trailing edge losses of the recontoured blades

Comparison of Experimental and Analytical Performance for Contoured Endwall Stators

Comparisons between predicted and experimental stator losses showed that the analysis was able to predict the change in stator loss when contoured endwalls with highly three dimensional passage geometry were used. The level of loss was predicted to within 75 percent of that measured. The predicted loss was due only to profile loss and boundary layer growth on the endwalls. The 25 percent difference was approximately 0.015 at design pressure ratio. The analysis was shown to predict the trend in stator flow angle, even for small stator geometries

Cold-air performance of compressor-drive turbine of Department of Energy upgraded automobile gas turbine engine. 1: Volute-manifold and stator performance

The aerodynamic performance of the inlet manifold and stator assembly of the compressor drive turbine was experimentally determined with cold air as the working fluid. The investigation included measurements of mass flow and stator-exit fluid torque as well as radial surveys of total pressure and flow angle at the stator inlet and annulus surveys of total pressure and flow angle at the stator exit. The stator-exit aftermixed flow conditions and overall stator efficiency were obtained and compared with their design values and the experimental results from three other stators. In addition, an analysis was made to determine the constituent aerodynamic losses that made up the stator kinetic energy loss

Analytical and experimental investigation of stator endwall countouring in a small axial-flow turbine

An experimental and analytical investigation was conducted to determine the effect of stator endwall contouring on turbine stage performance. In this investigation three stator configurations were evaluated using a common rotor. The three stator configurations were a cylindrical endwall design and two contoured endwall designs, one having a S-shaped outer wall profile and the other having a conical-shaped outer wall profile. Experimental data were obtained over a range of equivalent speeds, total pressure ratios, and rotor tip clearances for each stator-rotor combination. Detailed analytical loss assessments were conducted to aid in the determination of the contouring effect on turbine performance

Cold-air performance of compressor-drive turbine of department of energy upgraded automobile gas turbine engine. 3: Performance of redesigned turbine

The aerodynamic performance of a redesigned compressor drive turbine of the gas turbine engine is determined in air at nominal inlet conditions of 325 K and 0.8 bar absolute. The turbine is designed with a lower flow factor, higher rotor reaction and a redesigned inlet volute compared to the first turbine. Comparisons between this turbine and the originally designed turbine show about 2.3 percentage points improvement in efficiency at the same rotor tip clearance. Two versions of the same rotor are tested: (1) an as cast rotor, and (2) the same rotor with reduced surface roughness. The effect of reducing surface roughness is about one half percentage point improvement in efficiency. Tests made to determine the effect of Reynolds number on the turbine performance show no effect for the range from 100,000 to 500,000

Research on low voltage electroluminescent devices with storage, phase 1 Final report, 1 May 1967 - 29 Feb. 1968

Materials for electroluminescent display panel based on carrier injectio