Optimization of admixture and three-layer particleboard made from oil palm empty fruit bunch and rubberwood clones

Empty fruit bunch (EFB) is a biomass that is widely available and has the potential to be used as industrial raw material especially in wood-based industries. This study focuses on producing a particleboard by incorporating EFB with two different rubberwood clones: Prang Besar (PB) 260 and RRIM 2002, respectively. PB 260 is a commercially planted clone and wood from matured (>25 year-old) trees are used by wood-based panel manufacturers. RRIM 2002 is a new clone planted at the Malaysian Rubber Board (MRB) research trial plots and consists of only 4-year-old trees. Two types of particleboards (admixture and three-layer) with different ratios were produced. The Japanese Industrial Standard (JIS-5908 2003 particleboard) was used to evaluate mechanical and dimensional stability properties of the particleboards. From the study, it was found that admixture particleboards showed superior properties compared to three-layer particleboards. Layering EFB and rubberwood significantly decreased board performance for all properties (except internal bonding). The optimum ratios of EFB and both rubberwood clones are found to be 1:1 (50% EFB: 50% rubberwood). Meanwhile, increasing the rubberwood clones ratio to 70% lowered board performance especially for EFB (30%):RRIM 2002 clone (70%) boards which showed the lowest values for all properties for both admixture and three-layer board

Utilization of Renewable Biomass and Waste Materials for Production of Environmentally-Friendly, Bio-based Composites

The introduction of renewable biomass into a polymer matrix is an option competing with other possibilities, such as energy recovery and/or re-use in the carbonized state, or production of chemicals, such as, in the case of ligno-cellulosic waste, concentrates on the production of simple sugars, then possibly leading to the development of biopolymers. These competitive applications have also some interest and market, however with a considerable energy, water and materials consumption, due also to the not always high yielding. Other possibilities for renewable biomass are therefore being used as fillers to increase mechanical performance of polymers or to allow e.g., the absorption of toxic chemicals. This review concentrates on the use of biomass as close as possible to the “as received” state, therefore avoiding whenever suitable any thermal treatment. More specifically, it focuses on its introduction into the three categories of oil-based (or bio-based replacement) of engineered polymers, into industrial biopolymers, such as poly(lactic acid) (PLA) and self-developed biopolymers, such as thermoplastic starch (TPS)

IFSS, TG, FT-IR spectra of impregnated sugar palm (Arenga pinnata) fibres and mechanical properties of their composites.

This study aimed to investigate the effect of resin impregnation on the interfacial shear strength (IFSS), thermogravimetric (TG) and fourier transform infrared (FT-IR) of sugar palm (Arenga pinnata) fibres. In addition, the effect of resin impregnation on the mechanical properties of sugar palm fibre reinforced unsaturated polyester (UP) composites was also studied. The fibres were impregnated with UP via vacuum resin impregnation process at a pressure of 600 mmHg for 5 min. Composites of 10, 20, 30, 40 and 50 % fibre loadings were fabricated and tested for tensile and flexural properties. It was observed that the impregnation process caused the fibres to be enclosed by UP resin and this gave a strong influence to the increase of its interfacial bonding by the increase of its IFSS from single fibre pull-out test. It was also observed with TG and FT-IR spectra that the impregnated fibre had lower moisture uptake than the control and there was no significant increase in thermal stability of the impregnated fibre. The sequence of fibre decomposition started from the evaporation of moisture, hemicelluloses, cellulose, lignin and finally ash content and the presence of these components were proven by FT-IR spectra. For the composite specimens, due to the high interfacial bonding of the impregnated fibre and the matrix, the impregnated composites showed consistently higher tensile strength, tensile modulus, elongation at break, flexural strength, flexural modulus and toughness than the control samples. It was also observed that 30 % fibre loading gave optimum properties

Review of natural fibre-reinforced hybrid composites

Natural fibre-reinforced hybrid composites which contain one or more types of natural reinforcement are gaining increasing research interest. This paper presents a review of natural fibre-reinforced hybrid composites. Both thermoplastic and thermoset composites reinforced by hybrid/synthetic fibres or hybrid/hybrid fibres are reviewed. The properties of natural fibres, the properties and processing of composites are summarised

Selective Colorimetric Detection of Nitrite in Water using Chitosan Stabilized Gold Nanoparticles Decorated Reduced Graphene oxide

© 2017 The Author(s). Excess nitrite (NO 2 - ) concentrations in water supplies is considered detrimental to the environment and human health, and is associated with incidence of stomach cancer. In this work, the authors describe a nitrite detection system based on the synthesis of gold nanoparticles (AuNPs) on reduced graphene oxide (rGO) using an aqueous solution of chitosan and succinic acid. The AuNPs-rGO nanocomposite was confirmed by different physicochemical characterization methods including transmission electron microscopy, elemental analysis, X-ray diffraction, UV-visible (UV-vis) and Fourier transform infrared spectroscopy. The AuNPs-rGO nanocomposite was applicable to the sensitive and selective detection of NO 2 - with increasing concentrations quantifiable by UV-vis spectroscopy and obvious to the naked eye. The color of the AuNPs-rGO nanocomposite changes from wine red to purple with the addition of different concertation of NO 2 - . Therefore, nitrite ion concentrations can be quantitatively detected using AuNPs-rGO sensor with UV-vis spectroscopy and estimated with the naked eye. The sensor is able to detect NO 2 - in a linear response ranging from 1 to 20 μM with a detection limit of 0.1 μM by spectrophotometric method. The as-prepared AuNPs-rGO nanocomposite shows appropriate selectivity towards NO 2 - in the presence of potentially interfering metal anions

Harnessing the potential of ligninolytic enzymes for lignocellulosic biomass pretreatment

Abundant lignocellulosic biomass from various industries provides a great potential feedstock for the production of value-added products such as biofuel, animal feed, and paper pulping. However, low yield of sugar obtained from lignocellulosic hydrolysate is usually due to the presence of lignin that acts as a protective barrier for cellulose and thus restricts the accessibility of the enzyme to work on the cellulosic component. This review focuses on the significance of biological pretreatment specifically using ligninolytic enzymes as an alternative method apart from the conventional physical and chemical pretreatment. Different modes of biological pretreatment are discussed in this paper which is based on (i) fungal pretreatment where fungi mycelia colonise and directly attack the substrate by releasing ligninolytic enzymes and (ii) enzymatic pretreatment using ligninolytic enzymes to counter the drawbacks of fungal pretreatment. This review also discusses the important factors of biological pretreatment using ligninolytic enzymes such as nature of the lignocellulosic biomass, pH, temperature, presence of mediator, oxygen, and surfactant during the biodelignification process