47 research outputs found

    Exergoeconomic analysis for the design improvement of supercritical CO2 cycle in concentrated solar plant

    Get PDF
    In this work, an exergoeconomic analysis is applied to the power cycle of a concentrated solar plant for its design improvement. A supercritical CO2 cycle connected with the exothermic reactor of a thermochemical storage unit is considered. The analysis is conducted with the goal of highlighting the advantages of exergoeconomic analysis while suggesting changes to both the design parameters and the system configuration. Starting from the plant configuration which guarantees the maximum efficiency, the exergoeconomic analysis is iteratively applied with the goal of reducing the unit cost of electricity. The analysis is conducted in a way that cost functions of the components can be substituted with the cost analysis of specific designs. This is a big advantage of this procedure, which is suitable for applications in which economic analysis requires a detailed knowledge of the system characteristics. The procedure is then validated comparing the results with those obtained through mathematical optimization

    Optimal Installation of Heat Pumps in Large District Heating Networks

    Get PDF
    Power-to-heat technology represents a promising solution for the decarbonization of the energy sector. The installation of large-scale heat pumps within district heating systems is widely recognized to be a cost-effective and competitive way to provide flexibility to the electric system, enhancing the use of intermittent renewable energy sources. The goal of this paper is to show how the economic and environmental benefits provided by the installation of a large-scale heat pump in existing district heating systems vary according to the installation location in different scenarios. To do that, an integrated methodology is developed. This includes a physical model of the thermo-fluid dynamic of the district heating network and a detailed modeling of the heat pump. To compare the different positions and also the different operating conditions, an approach based on exergy analysis is adopted. Moreover, a specific control strategy of the mass-flow rate is analyzed to further reduce greenhouse gas emissions. The application to a real large-scale district heating network shows that reductions in CO2 emissions of almost 4% can be obtained by installing a single heat pump of about 4 MWe (over a total thermal load of about 305 MWt), while this positive effect can be reduced by up to 63% if placing the heat pump at non-optimal locations

    Integration of ThermoChemical Energy Storage in Concentrated Solar Power. Part 2: comprehensive optimization of supercritical CO2 power block

    Get PDF
    Abstract Among the various options of Thermo-Chemical Energy Storage, Calcium-Looping represents a promising alternative for Concentrated Solar Power plants, thanks to high operating temperatures, high energy density and absence of thermal losses. Finding the most suitable power cycle for this system is a task that has still to be solved and is not trivial because it consists in a complex process synthesis problem. From a preliminary analysis (Part 1), supercritical CO2 cycles results to be the most promising option. In the present work, the integration of this power block (pilot plant size, 2 MWe) is deeply investigated through a comprehensive analysis. Numerous thermal cycle layouts are considered and two options for the power block thermal feeding are assumed. The HEATSEP methodology (comprising genetic algorithm, pinch analysis and bisection) is adopted to optimize both components operating conditions and heat transfer processes in the discharging phase. The plant section devoted to the charging process is optimized and dimensioned taking into account the transient operation. Thanks to the complex problem structure developed, the algorithm is free to find the most suitable configuration between a huge set of feasible combinations. Both energy and economic optimizations are performed for the complete plant and, being in contrast between them, a multi-objective optimization is executed. The independent variables influence on the resulting configuration is assessed and intermediate layouts obtained from the Pareto curve are commented. Carbonator inlet temperature of reactants are observed to increase with plant efficiency. The maximum efficiency (21%) is obtained with the most complex power block (recompression, intercooling and reheating) exchanging heat directly on the carbonator wall. Less performing discharging processes are cheaper but determine higher costs of charging sections; the resulting effect is positive and the integration of simpler power blocks results economically convenient. A power cycle with single intercooling and thermal feeding performed on the carbonator outflows is the result of economic optimization (efficiency equal to 16.3%). The algorithm gives precedence to power block thermal feeding and then to reactants preheating. Novel plant layouts are designed for these configurations and data useful for further investigations are provided in the last part of this work

    Integration of ThermoChemical Energy Storage in Concentrated Solar Power. Part 1: energy and economic analysis/optimization

    Get PDF
    Coupling of Concentrated Solar Power and Thermo-Chemical Energy Storage is a very interesting option because of the high efficiencies attainable with a renewable source and the large variation of solar radiation. Thermo-Chemical Energy Storage based on Calcium-Looping represents a promising opportunity thanks to high operating temperature, high energy density, null thermal losses and cheap calcium oxide precursor exploitable. The large variety of suitable power blocks and the importance of their integration in the discharging process makes it necessary to perform a coherent analysis of the selected alternatives, in order to compare them and establish the most convenient integration. Many aspects must be taken into account, such as system efficiency, investment costs and layout complexity. The purposes of the present work are: the development of a methodology to simulate the entire plant operations; the synthesis of heat recovery systems for both the charging and discharging processes; the execution of an economic analysis and the development of economic optimizations for the design/dimensioning of solar side and calciner side. Between the options investigated, power blocks based on supercritical CO2 are the most convenient both in terms of global efficiency (higher than 19%) and capital investment, keeping this advantage also for higher plant sizes. The methodology here developed and the results obtained are useful information for a deeper analysis of the most promising integration alternative, which is performed in the second part of this study

    Including thermal network operation in the optimization of a Multi Energy System

    Get PDF
    The combined production of different energy vectors with Multi Energy Systems is a very attractive opportunity to increase the generation efficiency, compensate the oscillations of renewable sources, and improve the flexi-bility in power generation. Optimizing their operation is a complex task, since the problem can easily reach high dimensions, representing a challenge for commercial solvers. The inclusion in the optimization of a thermal network whose simulation is based on temperatures and flowrates allows to significantly improve the applica-bility of the obtained results. In addition, the effect of the operating temperatures on the performances of thermal components should be included as well. With these purposes, the present study proposes a strategy for the operation optimization of a MES and its internal thermal network. The model relies on a decomposition approach, where the original problem is divided in two subproblems. In the first one, the MES operating costs are minimized without considering the effects of the thermal network, while in the second one, the thermal network operation is optimized in order to find the operating conditions that are more favourable to the ones found for the MES. These subproblems are iteratively solved until the process converges to a stable solution. Some efforts are taken to keep the mathematical formulation as simple as possible (the MES is a Mixed Integer Linear Pro-gramming, while the heating network is a Quadratically Constrained Programming). The developed model al-lows to find near-optimal solutions which satisfy the numerous physical and technical constraints addressed. The results provide an optimized schedule for the thermal storage in terms of mass flowrates and temperature. One of the strengths of the model is the relatively low computational time required to reach the convergence and, despite not being the global optimum, the high quality of the solution obtained

    Optimal operation of district heating networks through demand response

    Get PDF
    In this paper, an optimization method aiming at minimizing the thermal peaks in district heating networks is proposed. The method relies on a thermo-fluid dynamic model of both the supply and return networks and permits to analyze the opportunities for thermal peak shaving through “virtual storage”. The latter is obtained through variation of the thermal request profiles of the users. The presence of a peak in the morning is due to the shut-down or attenuation of the heating systems during the night, which lead to a dramatical increase of the thermal request early in the morning. The peak compromises a full exploitation of cogeneration and renewable plants that are able to cover just a portion of the maximum load. Consequently, boilers have to be used, leading the system to a performance reduction and to an increase of primary energy consumption. Moreover, the peak makes the possibility of network extension quite difficult, because of the limitation on mass flow rates in the pipes. For this reason, a model is developed to make the thermal profile as flat as possible. The model is applied to a portion of the Turin district heating network, which is the largest network in Italy. Results show that reductions between 20% and 42% are possible, depending on the maximum changes in the possible schedules

    Optimal Configuration of Power-to-Cool Technology in District Cooling Systems

    Get PDF
    In a multienergy framework, power-to-heat technology is becoming increasingly attractive. This interest is mainly due to the possibility of exploiting excesses and unbalances of electricity, which are becoming more and more common with the increasing capacity of the renewable sources. An interesting option consists in using heat pumps to convert excess of electricity produced by photovoltaic systems (especially in the midday hours) into cold to be provided to district heating and district cooling networks. This article aims to propose a methodology to select the best heat pump location in district cooling system. The analysis is performed with the aim of minimizing the cost of network construction and pumping. The procedure includes the best heat pump location and the design of the pipeline. Results show that distributed heat pumps allow one reducing both the costs and the average pipeline diameters by about 50% with respect to concentrated production. Furthermore, the optimal location of distributed heat pumps allows reducing costs of about 7% with respect to a uniformly distributed production

    Compact model of latent heat thermal storage for its integration in multi-energy systems

    Get PDF
    Nowadays, flexibility through energy storage constitutes a key feature for the optimal management of energy systems. Concerning thermal energy, Latent Heat Thermal Storage (LHTS) units are characterized by a significantly higher energy density with respect to sensible storage systems. For this reason, they represent an interesting solution where limited space is available. Nevertheless, their market development is limited by engineering issues and, most importantly, by scarce knowledge about LHTS integration in existing energy systems. This study presents a new modeling approach to quickly characterize the dynamic behavior of an LHTS unit. The thermal power released or absorbed by a LHTS module is expressed only as a function of the current and the initial state of charge. The proposed model allows simulating even partial charge and discharge processes. Results are fairly accurate when compared to a 2D finite volume model, although the computational effort is considerably lower. Summarizing, the proposed model could be used to investigate optimal LHTS control strategies at the system level. In this paper, two relevant case studies are presented: (a) the reduction of the morning thermal power peak in District Heating systems; and (b) the optimal energy supply schedule in multi-energy systems

    Analytical approach for entropy generation and heat transfer in CNT-nanofluid dynamics through a ciliated porous medium

    Get PDF
    The transportation of biological and industrial nanofluids by natural propulsion like cilia movement and self-generated contraction-relaxation of flexible walls has significant applications in numerous emerging technologies. Inspired by multi-disciplinary progress and innovation in this direction, a thermo-fluid mechanical model is proposed to study the entropy generation and convective heat transfer of nanofluids fabricated by the dispersion of single-wall carbon nanotubes (SWCNT) nanoparticles in water as the base fluid. The regime studied comprises heat transfer and steady, viscous, incompressible flow, induced by metachronal wave propulsion due to beating cilia, through a cylindrical tube containing a sparse (i.e. high permeability) homogenous porous medium. The flow is of the creeping type and is restricted under the low Reynolds number and long wavelength approximations. Slip effects at the wall are incorporated and the generalized Darcy drag-force model is utilized to mimic porous media effects. Cilia boundary conditions for velocity components are employed to determine analytical solutions to the resulting non-dimensionalized boundary value problem. The influence of pertinent physical parameters on temperature, axial velocity, pressure rise and pressure gradient, entropy generation function, Bejan number and stream-line distributions are computed numerically. A comparative study between SWCNT nanofluids and pure water is also computed. The computations demonstrate that axial flow is accelerated with increasing slip parameter and Darcy number and is greater for SWCNT- nanofluids than for pure water. Furthermore the size of the bolus for SWCNT-nanofluids is larger than that of the pure water. The study is applicable in designing and fabricating nanoscale and microfluidics devices, artificial cilia and biomimetic micro-pump
    corecore