Investigation of the Superconducting and Magnetic Phase Diagram of Off-Stoichiometric LiFeAs

At their discovery in 2008, iron pnictide superconductors (IPS) provoked tremendous scientific interest, comparable to the discovery of the cuprate superconductors. So far, IPS reached critical temperatures T c up to 56K. Typically, they show an antiferromagnetic (afm) spin density wave (SDW) which has to be suppressed by doping before superconductivity develops, which then is supported by further doping. Due to the close vicinity of the magnetic and the superconducting (sc) phase, magnetic fluctuations are discussed to be responsible for the sc pairing mechanism in IPS. A special member of the IPS is LiFeAs, because it does not need doping to become sc. It is a stoichiometric superconductor at a T c of 18K. In fact, doping is suppressing its T c . Also, there is no sign of an afm SDW present. Therefore, LiFeAs is a interesting material to study the properties of the IPS in an undisturbed material. In 2010, experiments of the Leibniz Institute for Solid State and Materials Research Dresden (IFW Dresden) revealed further surprising properties of LiFeAs. Samples with a Li deficiency undergo a ferromagnetic (fm) phase transition at 165K. Theoretical calculations suggest that fm fluctuations could induce triplet superconductivity in LiFeAs. This would cause a nonvanishing dynamic susceptibility below T c , which is supported by nuclear magnetic resonance (NMR) experiments. This thesis is discussing the results of the IFW Dresden experiments, and concludes that this ferromagnetism is of weak itinerant nature. The origin might be an increase of the density of states (DOS) at the Fermi level, which is causing an instability towards fm order, as proposed by the Stoner model. For further doping experiments, the synthesis procedure of polycrystalline LiFeAs was optimized to get samples with maximum T c and minimum impurities. Therefore, nuclear quadrupole resonance (NQR) was used. The NQR line width is a measure of impurities in the sample. By minimizing the NQR line width, optimal samples were synthesized. These samples are able to compete with the properties of single crystals. To investigate the doping behavior of LiFeAs, a scenario with four different kinds of impurities and deficiencies was performed with the optimized synthesis procedure. 24 different samples were analyzed, by means of NQR and electrical conductivity. It was found that in fact Fe excess is responsible for changing the physical properties of LiFeAs, and not Li deficiency. It is causing a shrinking of the unit cell volume, as seen by X-ray diffraction (XRD) measurements and it causes a decrease of T c . It also leads to a decrease of room temperature resistivity, which is supporting an increase of the DOS at the Fermi level. The NQR frequency is scaling with the amount of Fe excess and can be used to draw the sc and fm phase diagram of off-stoichiometric LiFeAs. At an amount between 3.2 and 3.6% o f Fe excess LiFeAs undergoes the fm transition

Tetra-Responsive Grafted Hydrogels for Flow Control in Microfluidics

Microfluidics covers the science of manipulating small quantities of fluids using microscale devices with great potential in analysis, multiplexing, automation and high-throughput screening. Compared to conventional systems, microfluidics benefits from miniaturization resulting in shortened time of experiments, decreased sample and reagent consumptions as well as reduced overall costs. For microfluidic devices where further weight and cost reduction is additionally required, stimuli-responsive hydrogels are particularly interesting materials since they can convert an environmental stimulus directly to mechanical work without any extra power source. Hydrogels are used as chemostats, micropumps, and chemo-mechanical valves in microfluidics. Existing studies about hydrogels for flow control reported on hydrogels responsive to only one stimulus, including temperature, pH value, and solvent. Combining temperature and pH stimuli within one material is an interesting approach, which allows internal as well as external flow control and broadens potential applications. Among the variety of temperature- and pH-responsive monomers, N-isopropylacrylamide (NiPAAm) and acrylic acid (AA) are considered as ideal building blocks to obtain a hydrogel with pronounced stimuli response. There are different architectures for realizing a temperature- and pH-responsive hydrogel with NiPAAm and AA (e.g. copolymer gels, interpenetrating polymer networks (IPNs), semi-IPNs, or graft copolymer gels). Each approach has its inherent benefits and disadvantages. Grafted hydrogels with a temperature-responsive backbone and pH-responsive graft chains are a promising architecture overcoming drawbacks of copolymer gels (loss of thermoresponsive behavior due to the comonomer), interpenetrating polymer networks (IPNs, difficult fabrication of structured particles via soft lithography), and semi-IPNs (leakage of penetrating polymer). However, studies about multi-responsive grafted hydrogels for flow control in microfluidics are comparatively rare and further research is needed to emphasize their real potential. For this reason, the overall aim of this work was the synthesis of temperature- and pH-responsive grafted hydrogels based on NiPAAm and AA for flow control in microfluidics. This required the synthesis of a pH-responsive macromonomer by RAFT polymerization. As a suitable chain transfer agent with a carboxylic acid group for an end-group functionalization, 2-(dodecyl-thiocarbonothioylthio)-2-methylpropionic (DTP) acid was employed. The approach towards the synthesis of the pH-responsive macromonomer based on two key steps: (i) attaching a functional group, which retains during RAFT polymerization, and (ii) conducting the RAFT polymerization to synthesize the pH-responsive macromonomer. In total, four functionalizations for the macromonomer were investigated, including allyl, unconjugated vinyl, acrylamide, and styrene. End-group analysis and solubility tests revealed that macromonomers with a styrene functionalization are suitable for the synthesis of graft copolymer gels. A series of grafted net-PNiPAAm-g-PAA-styrene hydrogels with a PNiPAAm backbone and PAA-styrene graft chains (Mn = 4200 g/mol, Mw/Mn = 1.6) were prepared and characterized. The main goal was to identify suitable stimuli for an application as a chemo-mechanical valve and to show reversibility of the swelling and shrinking process. Importantly, the temperature sensitivity should be retained, while a pH response needs to be introduced. Equilibrium swelling studies quantified with the response ratio revealed that a grafting density of PAA-styrene between 0.25 and 1 mol-% provides a suitable response towards temperature, pH, salt, and solvent. Furthermore, the swelling and shrinking process is highly reproducible over four consecutive cycles for all four stimuli. In order to evaluate the swelling kinetics of grafted net-PNiPAAm-g-PAA-styrene hydrogels, the collective diffusion model extended by a volume specific surface was applied. The determined cooperative diffusion coefficients of net-PNiPAAm-g-PAA-styrene indicated faster response time with increasing PAA-styrene content. Remarkably, net-PNiPAAm-g-PAA-styrene containing 1 mol-% PAA-styrene exhibited an accelerated swelling rate by a factor of 9 compared to pure net-PNiPAAm. Rheological analysis of net-PNiPAAm-g-PAA-styrene showed that an increasing graft density leads to decreasing mechanical stability. The photopolymerization experiments showed that the gelation time linearly increases with the grafting density. Grafted net-PNiPAAm-g-PAA-styrene hydrogels were tested in two fluidic setups for flow control. A straightforward fluidic platform was developed consisting of a fluid reservoir, an inlet channel, an actuator chamber and an outlet channel. The actuator chamber was filled with crushed hydrogel particles. Accordingly, the fluid flow was directed by the active resistance of the hydrogel particles in the actuator chamber (i.e. swelling degree) and allowed flow control by the local environmental conditions. Flow rate studies showed that the fluid flow throttles when the inlet channel was provided with a solution in which the hydrogel swells (pH 9 buffer solution at room temperature). In contrast, the hydrogel-based valve opens immediately when a solution was used in which the hydrogel collapses. The advantageous properties of net-PNiPAAm-g-PAA-styrene were highlighted by using pH, salt and solvent stimulus in one experiment. Remarkably, the opening and closing function was reversible over six consecutive cycles. As part of a collaboration project with the chair of polymeric microsystems within the Cluster of Excellence Center for Advancing Electronics Dresden (A. Richter and P. Frank), membrane assures hydraulic coupling in a chemo-fluidic membrane transistor (CFMT) and grafted net-PNiPAAm-g-PAA-styrene hydrogels were combined to emphasize the potential of both systems. Flow rate studies showed that 4 different stimuli can be used to control the opening and closing state of the CFMT. Multiple opening and closing cycles revealed no considerable changes in the valve function emphasizing a high potential for an application in microfluidics

Tetra-Responsive Grafted Hydrogels for Flow Control in Microfluidics

Microfluidics covers the science of manipulating small quantities of fluids using microscale devices with great potential in analysis, multiplexing, automation and high-throughput screening. Compared to conventional systems, microfluidics benefits from miniaturization resulting in shortened time of experiments, decreased sample and reagent consumptions as well as reduced overall costs. For microfluidic devices where further weight and cost reduction is additionally required, stimuli-responsive hydrogels are particularly interesting materials since they can convert an environmental stimulus directly to mechanical work without any extra power source. Hydrogels are used as chemostats, micropumps, and chemo-mechanical valves in microfluidics. Existing studies about hydrogels for flow control reported on hydrogels responsive to only one stimulus, including temperature, pH value, and solvent. Combining temperature and pH stimuli within one material is an interesting approach, which allows internal as well as external flow control and broadens potential applications. Among the variety of temperature- and pH-responsive monomers, N-isopropylacrylamide (NiPAAm) and acrylic acid (AA) are considered as ideal building blocks to obtain a hydrogel with pronounced stimuli response. There are different architectures for realizing a temperature- and pH-responsive hydrogel with NiPAAm and AA (e.g. copolymer gels, interpenetrating polymer networks (IPNs), semi-IPNs, or graft copolymer gels). Each approach has its inherent benefits and disadvantages. Grafted hydrogels with a temperature-responsive backbone and pH-responsive graft chains are a promising architecture overcoming drawbacks of copolymer gels (loss of thermoresponsive behavior due to the comonomer), interpenetrating polymer networks (IPNs, difficult fabrication of structured particles via soft lithography), and semi-IPNs (leakage of penetrating polymer). However, studies about multi-responsive grafted hydrogels for flow control in microfluidics are comparatively rare and further research is needed to emphasize their real potential. For this reason, the overall aim of this work was the synthesis of temperature- and pH-responsive grafted hydrogels based on NiPAAm and AA for flow control in microfluidics. This required the synthesis of a pH-responsive macromonomer by RAFT polymerization. As a suitable chain transfer agent with a carboxylic acid group for an end-group functionalization, 2-(dodecyl-thiocarbonothioylthio)-2-methylpropionic (DTP) acid was employed. The approach towards the synthesis of the pH-responsive macromonomer based on two key steps: (i) attaching a functional group, which retains during RAFT polymerization, and (ii) conducting the RAFT polymerization to synthesize the pH-responsive macromonomer. In total, four functionalizations for the macromonomer were investigated, including allyl, unconjugated vinyl, acrylamide, and styrene. End-group analysis and solubility tests revealed that macromonomers with a styrene functionalization are suitable for the synthesis of graft copolymer gels. A series of grafted net-PNiPAAm-g-PAA-styrene hydrogels with a PNiPAAm backbone and PAA-styrene graft chains (Mn = 4200 g/mol, Mw/Mn = 1.6) were prepared and characterized. The main goal was to identify suitable stimuli for an application as a chemo-mechanical valve and to show reversibility of the swelling and shrinking process. Importantly, the temperature sensitivity should be retained, while a pH response needs to be introduced. Equilibrium swelling studies quantified with the response ratio revealed that a grafting density of PAA-styrene between 0.25 and 1 mol-% provides a suitable response towards temperature, pH, salt, and solvent. Furthermore, the swelling and shrinking process is highly reproducible over four consecutive cycles for all four stimuli. In order to evaluate the swelling kinetics of grafted net-PNiPAAm-g-PAA-styrene hydrogels, the collective diffusion model extended by a volume specific surface was applied. The determined cooperative diffusion coefficients of net-PNiPAAm-g-PAA-styrene indicated faster response time with increasing PAA-styrene content. Remarkably, net-PNiPAAm-g-PAA-styrene containing 1 mol-% PAA-styrene exhibited an accelerated swelling rate by a factor of 9 compared to pure net-PNiPAAm. Rheological analysis of net-PNiPAAm-g-PAA-styrene showed that an increasing graft density leads to decreasing mechanical stability. The photopolymerization experiments showed that the gelation time linearly increases with the grafting density. Grafted net-PNiPAAm-g-PAA-styrene hydrogels were tested in two fluidic setups for flow control. A straightforward fluidic platform was developed consisting of a fluid reservoir, an inlet channel, an actuator chamber and an outlet channel. The actuator chamber was filled with crushed hydrogel particles. Accordingly, the fluid flow was directed by the active resistance of the hydrogel particles in the actuator chamber (i.e. swelling degree) and allowed flow control by the local environmental conditions. Flow rate studies showed that the fluid flow throttles when the inlet channel was provided with a solution in which the hydrogel swells (pH 9 buffer solution at room temperature). In contrast, the hydrogel-based valve opens immediately when a solution was used in which the hydrogel collapses. The advantageous properties of net-PNiPAAm-g-PAA-styrene were highlighted by using pH, salt and solvent stimulus in one experiment. Remarkably, the opening and closing function was reversible over six consecutive cycles. As part of a collaboration project with the chair of polymeric microsystems within the Cluster of Excellence Center for Advancing Electronics Dresden (A. Richter and P. Frank), membrane assures hydraulic coupling in a chemo-fluidic membrane transistor (CFMT) and grafted net-PNiPAAm-g-PAA-styrene hydrogels were combined to emphasize the potential of both systems. Flow rate studies showed that 4 different stimuli can be used to control the opening and closing state of the CFMT. Multiple opening and closing cycles revealed no considerable changes in the valve function emphasizing a high potential for an application in microfluidics

Vignette 2. When the global comes crashing in - a chance for GCE? Reflections on teaching refugees in ethics instruction in Berlin

Based on an ethnographic study in Berlin\u27s secondary school ethics classrooms, the author presents two scenarios that describe how teachers responded to and were challenged by the large influx of refugees that arrived in Germany during the summer and fall of 2015. Specifically, the narratives show how a male teacher\u27s effort to engage his students in a positive exchange with refugee students was challenged by the constant criticism of refugee students by another teacher. The second portrayal describes how a female teacher, in reflecting on her engagement with refugee students and her regular ethics classes, came over the course of an interview to see (religious) diversity as an important aspect with which to engage students in her teaching. Overall, these two examples show how students\u27 experiences of learning about diversity, citizenship, and the global depended considerably on whether or not teachers saw diversity as an opportunity for learning or something requiring discipline; in other words, whether a global geopolitical crisis was treated as an opportunity or a catastrophe. (DIPF/Orig.

Tapering of fs Laser-written Waveguides

The vast development of integrated quantum photonic technology enables the implementation of compact and stable interferometric networks. In particular laser-written waveguide structures allow for complex 3D-circuits and polarization-encoded qubit manipulation. However, the main limitation for the scale-up of integrated quantum devices is the single-photon loss due to mode-profile mismatch when coupling to standard fibers or other optical platforms. Here we demonstrate tapered waveguide structures, realized by an adapted femtosecond laser writing technique. We show that coupling to standard single-mode fibers can be enhanced up to 77% while keeping the fabrication effort negligible. This improvement provides an important step for processing multi-photon states on chip