234 research outputs found

    Efeito da idade na resistência de união

    Get PDF
    Este estudo avaliou, in vitro, o efeito da idade na resistência à tração do sistema adesivo Prime & Bond NT no substrato dentinário. Foram utilizados terceiros molares humanos de cinco faixas etárias: A- 17 a 20, B- 21 a 30, C- 31 a 40, D- 41 a 50 e E- 51 a 63. O esmalte oclusal foi removido utilizando disco de diamante e a superfície dentinária abrasionada e planificada com lixa de SiC (600) sob refrigeração. O sistema adesivo foi aplicado de acordo com as recomendações do fabricante e um bloco de resina composta de 6 mm de altura foi confeccionado na superfície dentinária. Os dentes foram armazenados em água por 24 horas a 37ºC e preparados para o ensaio de micro-tração. Cada espécime foi fixado no dispositivo de micro-tração que estava acoplado a uma máquina universal de ensaio e testado numa velocidade de 0,5 mm/min. As médias de resistência à tração foram (MPa): A- 21,42 ± 7,52ª; B- 30,13 ± 10,19ª; C- 31,69 ± 11,78ª; D- 30,69 ± 8,47ª e E- 35,66 ± 9,54ª. Nenhuma diferença significativa foi observada entre os grupos formados pelas faixas etárias (p >; 0,05). Os resultados sugerem que a idade não altera significativamente a resistência de união do sistema adesivo à dentina.This in vitro study evaluated the effect of tooth age on the tensile bond strength of Prime & Bond NT adhesive system to dentin. Human third molars from the five age groups were analyzed: A- 17 to 20yrs, B- 21 to 30yrs, C- 31 to 40yrs, D- 41 to 50yrs and E- 51 to 63yrs. The occlusal enamel was removed using a diamond saw under water cooling and the dentin surface was wet-ground with 600-grit SiC paper to obtain flat surfaces. The adhesive system was applied according to the manufacturer's instructions and a 6-mm high resin "crown" was built-up with resin composite. Teeth were stored for 24 hours in distilled water at 37ºC and prepared for micro-tensile testing. Each specimen was mounted in a testing jig attached to a universal testing machine and stressed in tension at a crosshead speed of 0.5mm/min until failure. The means of tensile bond strength were (MPa): A- 21.42 ± 7.52ª; B- 30.13 ± 10.19ª; C- 31.69 ± 11.78ª; D- 30.69 ± 8.47ª and E- 35.66 ± 9.54ª. No statistically significant difference was observed among the age groups (p >; 0.05). The results suggested that the tensile bond strength of the adhesive system was not significantly affected by dentin aging

    Morfologia e espessura da difusão de resina através da matriz de dentina desmineralizada ou sem condicionamento

    Get PDF
    The formation of a hybrid layer is the main bonding mechanism of current dentin-bonding systems. This study evaluated the morphology and thickness of the resin-infiltrated dentinal layer after the application of adhesive systems. The dentin-bonding agents were evaluated on flat dentinal preparations confected on the occlusal surfaces of human teeth. The test specimens were prepared and inspected under scanning electron microscopy at a magnification of X 2,000. The adhesive systems were responsible for different hybrid layer thicknesses (p < 0.05), and the mean values were: for Scotchbond MP Plus (SM), 7.41 ± 1.24mum; for Single Bond (SB), 5.55 ± 0.82mum; for Etch & Prime 3.0 (EP), 3.86 ± 1.17mum; and for Clearfil SE Bond (CB), 1.22 ± 0.45mum. The results suggest that the conventional three-step adhesive system (SM) was responsible for the thickest hybrid layer, followed by the one-bottle adhesive (SB). The self-etching adhesives, EP and CB, produced the formation of the thinnest hybrid layers.A formação da camada híbrida representa o principal mecanismo de união dos sistemas adesivos odontológicos. Este estudo avaliou a micromorfologia e a espessura da camada híbrida formada por adesivos dentinários. Os adesivos foram avaliados em preparos planificados de dentina na região oclusal de dentes humanos. Os espécimes foram preparados e analisados em MEV sob 2.000 X de magnitude. Os sistemas adesivos mostraram formação de diferentes espessuras de camada híbrida (p < 0,05) e suas médias foram (mim): para o Scotchbond MP Plus (SM), 7,41 ± 1,24; para o Single Bond (SB), 5,55 ± 0,82; para o Etch & Prime 3.0 (EP), 3,86 ± 1,17 e, para o Clearfil SE Bond (CB), 1,22 ± 0,45. Os resultados sugerem que o adesivo convencional (SM) seguido do adesivo de frasco único (SB) mostraram a formação das camadas híbridas com maior espessura, enquanto os adesivos autocondicionantes EP e CB, formaram respectivamente as mais delgadas

    Efeito da densidade e da area ocupada pelos tubulos dentinarios na resistencia a tração

    Get PDF
    Orientador: Luis Roberto Marcondes MartinsTese (doutorado) - Universidade Estadual de Campinas, Faculdade de Odontologia de PiracicabaResumo: O propósito deste estudo foi o avaliar efeito da densidade (DT) e da área ocupada pelos túbulos dentinários (AO) na resistência à tração (RT) de dois sistemas adesivos: Clearfil Liner Bond 2/Kuraray (LB) e Prime & Bond 2.1/Dentsply (PB). Dezenove terceiros molares humanos foram abrasionados a partir da superfície oclusal com lixas de SiC (granulação 600), para exporem uma superfície plana em 3 diferentes níveis de profundidade dentinária: profunda, média e superficial. Os sistemas adesivos foram aplicados de acordo com as recomendações dos fabricantes e coroas de compósito (Z 100/3M) com altura de 10 mm foram confeccionadas nessas superfícies. Após 24 horas de armazenamento em solução salina a 37° C, secções foram realizadas paralelamente ao longo eixo das amostras nos sentidos mésio-distal e vestíbulo-lingual. De cada amostra foram retirados três espécimes, os quais foram submetidos ao teste de microtração com velocidade de 0,5mm/min. Os espécimes que fraturaram na interface de união, tiveram sua superfície em dentina polida ('AL IND.2¿ O IND. 3¿-1000) e condicionada com ácido fosfórico 37% por 15 segundos, para serem observados em MEV em magnificações de 1000X e 4000X. Os valores médios de RT, em MPa, foram: LB:26,04 '+ Ou ¿' 10,25 e PB: 42,64 '+ Ou ¿' 15,20. A análise de regressão linear mostrou, para o adesivo PB, uma significante relação inversa (p0,05) foi observada entre os dois parâmetros (TD X RT - ('R POT. 2¿ = 0,0508 e AO X RT - ('R POT. 2¿ = 0,2066) para o adesivo LB. Os resultados sugerem que quanto maior a DT e AO, menor a RT para o adesivo PB. O adesivo PB apresentou valores médios de RT superiores em relação ao adesivo LBAbstract: The purpose of this study was evaluate the influence of tubule density (TD) and the area they occupy (AO) on tensile bond strength (BS) to dentin of two adhesive system; Prime & Bond 2.1/Dentsply (PB) and Clearfil Liner Bond 2/Kuraray (LB). Nineteen extracted human third molars were abraded with SiC paper discs (600-grit) from the occlusal surface to expose superficial, middle or deep dentin. The adhesive systems were applied to the fIat exposed surfaces according to the manufacturer's instructions and resin build-up "crowns" approximately 10.0 mm high were constructed incrementaly with resin composite (Z-100/3M). After 24 hours storage in physiological saline at 37 °C, the bonded specimens were serially sectioned in both "x"and "y" directions transversally to the bonded interface to obtain three repetitions of bonded sticks, per tooth. Each bonded stick was tested under tension in a DL-500 (Emic) tester aí 0,5mm/min. The specimens which failed adhesively at an interface, had their bonded dentin surface briefly abraded (1000 -grit ('AL IND.2¿ O IND. 3¿) and etched with 37% phosphoric acid for 15 seconds. This was, to permit SEI to be taken at 1000X and 4000X (DSM 940-A/Zeiss) and the DT and AO to be calculated per area (mm2). Mean bond strength of specimens tested were, in MPa LB: 26.04 '+ Ou ¿' 10.25 e PB: 42.64 '+ Ou ¿' 15.20. For PB the linear regression showed a significant (p<0.05) inverse relationship between the DT and BS ('R POT. 2¿ = 0.6309); and AO and BS strength ('R POT. 2¿ = 0.6638). No statistically significant correlation was observed between the two parameters for LB (TD X BS - 'R POT. 2¿ = 0.0508 e TA X BS - 'R POT. 2¿ = 0.2066). Results suggest that the greater the TD and greater the TA, the lower the BS of PB adhesive system to dentin. PB showed significantly high bond strengths than LBDoutoradoDentísticaDoutor em Clínica Odontológic

    Efeitos de agentes dessensibilizantes na obliteração de túbulos dentinários

    Get PDF
    O objetivo deste estudo foi avaliar as características de obliteração dos túbulos dentinários de três agentes dessensibilizantes: produto a base de oxalato de potássio / Oxa-Gel (OX), produto a base de HEMA e glutaraldeído / Gluma Desensitizer (GD) e produto a base de flúor-fosfato acidulado / Nupro Gel (AF). A região vestibular e cervical de vinte e quatro terceiros molares humanos extraídos foi planificada e polida com lixas de SiC e pastas de diamante para simular superfícies vestibulares dentinárias cervicais com hipersensibilidade. Os dentes foram aleatoriamente divididos em quatro grupos (n=6), de acordo com os seguintes tratamentos superficiais da dentina: G1: sem tratamento; G2: OX; G3: GD; G4: AF. Os espécimes foram fraturados no sentido línguo-vestibular e preparados para microscopia eletrônica de varredura (MEV). OX promoveu oclusão pela deposição de cristais no interior dos túbulos. Enquanto, GL criou uma camada delgada sobre a superfície da dentina, a aplicação do AF produziu a formação de precipitados que ocluíram os túbulos. De acordo com a análise em MEV, todos agentes dessensibilizantes testados foram capazes de obliterar túbulos dentinários.The aim of this study was to evaluate the features of dentinal tubules occlusion following application of three commercially available desensitizing agents: potassium oxalate-based / Oxa-Gel (OX), HEMA and glutaraldehyde-based / Gluma Desensitizer (GD) and acidulated phosphate fluoride-based / Nupro Gel (AF). Buccal cervical areas of twenty-four extracted human third molars were smoothed and wet-polished with SiC papers and diamond pastes, in order to simulate the clinical aspect of hypersensitive dentin cervical surfaces. The teeth were randomly divided into four groups (n=6), according to the dentin surface treatments: G1: untreated; G2: OX; G3: GD; G4: AF. Specimens were fractured in the lingual-buccal direction and prepared for SEM analysis. OX promoted tubule occlusion by crystal-like deposits in the lumen of the tubules. While GL created a thin layer over the dentin surface, AF application produced precipitates that occluded the tubules. According to the SEM analysis, all desensitizing agents were able to occlude the dentinal tubules

    Avaliação em MEV do padrão de condicionamento do esmalte dental promovido por monômeros ácidos e o ácido fosfórico

    Get PDF
    ABSTRACT OBJECTIVE: Although self-etching bonding systems (SES) are indicated to prepare dental enamel for bonding, concerns have been expressed regarding their effectiveness. The aim of this study was to analyze the etching pattern (EP) of nine SES in comparison with 35% and 34% phosphoric acid etchants (FA) on intact (IN) and ground (GR) enamel surface. MATERIALS AND METHODS: Twenty-two human third molars were sectioned in mesial-distal and buccal-lingual directions, and four dental fragments were obtained from each tooth. Half of the fragments were ground using 600-grit SiC paper and the other half remained intact. The fragments were randomly assigned into 22 groups, according to the texture of enamel surface (IN and GR) and the technique to etch the enamel (34% FA, 35% FA, AdheSE primer; Brush & Bond; Clearfil Protect Bond primer; iBond; One-up Bond F; OptiBond Solo Plus primer; Tyrian SPE primer; Unifil Bond primer and Xeno III). Conditioners were applied to IN and GR enamel surfaces, according to the manufacturer's instructions. Specimens etched with phosphoric acids were washed with water, while the surfaces treated with SES were submitted to alternate rinsing with alcohol and acetone. The specimens were dried, sputter-coated and examined under a scanning electron microscope. RESULTS: For both IN and GR enamel surfaces, the EP of 34 and 35% FA was deeper and more homogeneous in comparison to EP of SES, except for Tyrian SPE. The acidic monomer action of self-etching systems was more effective on GR enamel. CONCLUSION: Most of the SES are less aggressive than phosphoric acid etchants and their etching effects were reduced on intact enamel surfaces.OBJETIVO: Apesar dos sistemas adesivos autocondicionantes (SAA) serem indicados para aplicação no esmalte dental, preocupação tem sido relatada com relação a sua efetividade. O objetivo deste estudo foi avaliar o padrão de condicionamento ácido (PCA) promovido por nove SAA e comparar ao PCA produzido pelo ácido fosfórico (35% e 34% - AF) no esmalte intacto (EI) ou abrasionado (EA). MATERIAIS E MÉTODOS: Vinte e dois terceiros molares humanos foram seccionados nos sentidos mésio-distal e vestíbulo-lingual, e quatro fragmentos dentais foram obtidos a partir de cada dente. Metade dos fragmentos tiveram o esmalte abrasionado com lixas de SiC (600) e a outra metade permaneceu intacta. Os fragmentos foram divididos em 22 grupos, de acordo com a textura da superfície do esmalte (EI e EA) e a técnica de condicionar o esmalte (AF 34 %, AF 35%, AdheSE primer; Brush & Bond; Clearfil Protect Bond primer; iBond; One-up Bond F; OptiBond Solo Plus primer; Tyrian SPE primer; Unifil Bond primer e Xeno III). Os agentes condicionadores foram aplicados nos EI e EA, de acordo com as instruções dos fabricantes. Espécimes tratados com AF foram lavados com água, enquanto os dentes tratados com SAA foram tratados com banhos alternados de álcool e acetona. Os espécimes foram secos, metalizados e observados em microscopia eletrônica de varredura. RESULTADOS: Em ambas as superfícies (EI e EA), o PCA dos AF (34 e 35%) foi mais profundo e homogêneo, quando comparados ao PCA produzido pelos SAA, exceto para o adesivo Tyrian SPE. A ação dos monômeros ácidos dos SAA foi mais efetiva no EA. CONCLUSÃO: A maioria dos SAA é menos agressiva que o ácido fosfórico e seus efeitos condicionadores são reduzidos em superfícies de EI

    Accuracy of irradiance and power of light-curing units measured with handheld or laboratory grade radiometers

    Get PDF
    This study measured and compared exitance irradiance and power of 4 commercial dental light-curing units (LCU) (Elipar S10, Elipar DeepCure-S, Corded VALO and Bluephase Style) using different types of radiometers. The devices used to analyze the LCU were classified as either handheld analog (Henry Schein, Spring, Demetron 100A, Demetron 100B and Demetron 200), handheld digital (Bluephase 1, Bluephase II, Coltolux, CureRite and Hilux), or laboratory instruments (Thermopile and Integrating Sphere). The laboratory instruments and the Bluephase II radiometer were also used to measure the LCU’s power (mW). The LCU’s were activated for 20 s (n=5). Data were analyzed using Kruskal-Wallis and Student-Newman-Keuls multiple comparison test (a=0.05). Among the LCU, the laboratory instruments presented different irradiance values, except for Corded VALO. The Coltolux and Hilux radiometers measured greater irradiance values compared to the laboratory instruments for the four LCUs tested. Within a given LCU, handheld analog units measured lower irradiance values, compared to handheld digital and laboratory instruments, except using the Spring radiometer for the Elipar S10 LCU. None of the handheld radiometers were able to measure similar irradiance values compared to laboratory instruments, except for Elipar S10 when comparing Bluephase 1 and Thermopile. Regarding power measurement, Bluephase II always presented the lowest values compared to the laboratory instruments. These findings suggest that the handheld radiometers utilized by practitioners (analog or digital) exhibit a wide range of irradiance values and may show lower outcomes compared to laboratory based instruments304397403CONSELHO NACIONAL DE DESENVOLVIMENTO CIENTÍFICO E TECNOLÓGICO - CNPQ307217-2014-0This study was supported by Brazilian Financial Agencies: FAEPEX-UNICAMP(2054/16) and CNPq (307217-2014-0

    Effect of carbamide peroxide-based bleaching agents containing fluoride or calcium on tensile strength of human enamel

    Get PDF
    OBJECTIVE: The aim of this study was to evaluate the effects of carbamide peroxide-based bleaching agents (CPG) containing fluoride (CF) or calcium (CCa) on the ultimate tensile strength of enamel (UTS). METHOD: A "cube-like" resin composite structure was built-up on the occlusal surface of twenty-two sound third molars to facilitate specimen preparation for the micro-tensile test. The restored teeth were serially sectioned in buccal-lingual direction in slices with approximate 0.7 mm thickness. Each slice was trimmed with a fine diamond bur to reduce the buccal, internal slope enamel of the cusps to a dumb-bell shape with a cross-sectional area at the "neck" of less than 0.5 mm². The samples were randomly divided into 12 groups (n=11). The control groups were not submitted to the bleaching regimen. Specimens were treated with 10% CPG gel or with 10% CPG formulations containing CF (0.2% and 0.5%) or CCa (0.05% and 0.2%). Bleached groups received the application of the 10% CPGs for 6 hours/day at 37º C, during 14 consecutive days and were stored in artificial saliva (AS) or 100% relative humidity (RH) among each application. After bleaching, specimens were tested with the microtensile method at 0.5 mm/min. Data were analyzed by two-way ANOVA and Tukey test (5%). RESULTS: No significant difference was observed between groups stored in AS or RH. Specimens treated with CF or CCa presented similar UTS as unbleached control groups. CONCLUSION: Either 10% CPG formulations containing CF or CCa can preserve the UTS after bleaching regimen.OBJETIVO: O propósito deste estudo foi avaliar os efeitos de agents clareadores à base de peróxido de carbamida (CPG) contendo fluoreto (CF) e cálcio (CCa) na resistência à tração do esmalte (UTS). MÉTODO: Um bloco de resina composta foi confeccionada na superfície oclusal de vinte e dois terceiros molars hígidos para facilitar a preparação dos espécimes para o teste de micro-tração. Os dentes restaurados foram seccionados com disco diamantado no sentido vestíbulo-lingual em fatias de aproximadamente 0,7 mm de espessura. Com uma ponta diamantada, foi realizada uma constrição na região de esmalte da vertente oclusal interna. Os espécimes apresentaram aproximadamente 0,5 mm² de área na secção transversal da região de constrição e foram divididos em 12 grupos (n=11). Os grupos controles não foram submetidos ao regime clareador e os experimentais foram tratados com gel de CPG 10% ou com formulações de CPG 10% contendo CF (0,2% e 0,5%) ou CCa (0,05% e 0,2%). Os grupos clareadores receberam a aplicação dos CPGs por 6 horas/dia a 37ºC, durante 14 dias consecutivos e foram armazenados em saliva artificial (AS) ou em umidade relativa 100% (RH), entre as aplicações do gel clareador. Após o clareamento, os espécimes foram testados através do método de micro-tração (0,5 mm/min). Os dados foram analisados pela ANOVA (2 fatores) e teste Tukey (5%). RESULTADOS: Nenhuma diferença foi observada entre os grupos armazenados em AS ou RH. Os espécimes tratados com CPG com CF ou Cca apresentaram similar UTS aos grupos controles não clareados. CONCLUSÃO: Ambos CPGs 10% CF or CCa não alteraram a UTS após o tratamento clareador

    Effect of surface treatments of laboratory-fabricated composites on the microtensile bond strength to a luting resin cement

    Get PDF
    The purpose of this study was to evaluate the influence of different surface treatments on composite resin on the microtensile bond strength to a luting resin cement. Two laboratory composites for indirect restorations, Solidex and Targis, and a conventional composite, Filtek Z250, were tested. Forty-eight composite resin blocks (5.0 x 5.0 x 5.0mm) were incrementally manufactured, which were randomly divided into six groups, according to the surface treatments: 1- control, 600-grit SiC paper (C); 2- silane priming (SI); 3- sandblasting with 50 mm Al2O3 for 10s (SA); 4- etching with 10% hydrofluoric acid for 60 s (HF); 5- HF + SI; 6 - SA + SI. Composite blocks submitted to similar surface treatments were bonded together with the resin adhesive Single Bond and Rely X luting composite. A 500-g load was applied for 5 minutes and the samples were light-cured for 40s. The bonded blocks were serially sectioned into 3 slabs with 0.9mm of thickness perpendicularly to the bonded interface (n = 12). Slabs were trimmed to a dumbbell shape and tested in tension at 0.5mm/min. For all composites tested, the application of a silane primer after sandblasting provided the highest bond strength means.O objetivo deste estudo foi avaliar a influência de diferentes tratamentos de superfície na resistência de união de resinas compostas a um agente de fixação resinoso. Dois compósitos de laboratório, Solidex e Targis, e um compósito convencional, Filtek Z250, foram testados. Quarenta e oito blocos de resina composta (5.0 x 5.0 x 5.0mm) foram confeccionados através da técnica incremental, para cada compósito testado, e foram aleatoriamente divididos em 6 grupos. Os blocos foram submetidos a seis tratamentos de superfície: 1 - Controle, Lixa 600-SiC (C); 2 - Silanização (SI); 3 - Jateamento com Al2O3 50µm por 10 segundos (SA); 4 - Condicionamento com ácido fluorídrico por 60 segundos (HF); 5 - HF + SI; 6 - SA + SI. Blocos submetidos ao mesmo tratamento foram unidos com o agente de fixação resinoso Rely X. Uma carga de 500g foi aplicada por 5 minutos e as amostras foram fotoativadas por 40 segundos. Os blocos unidos foram seccionados em fatias de 0.9mm de espessura perpendicularmente à interface de união (n = 12). Foram realizadas constrições limitando a interface de união a 1mm e as amostras foram levadas para o ensaio de tração. As maiores médias de união foram obtidas para as amostras submetidas à aplicação do silano após o jateamento com Al2O3

    Enamel susceptibility to red wine staining after 35% hydrogen peroxide bleaching

    Get PDF
    Concern has been expressed regarding the staining of enamel surface by different beverages after bleaching. This study investigated the influence of 35% hydrogen peroxide bleaching agents on enamel surface stained with wine after whitening treatments. Flat and polished bovine enamel surfaces were submitted to two commercially available 35% hydrogen peroxide bleaching agents or kept in 100% humidity, as a control group (n = 10). Specimens of all groups were immersed in red wine for 48 h at 37°C, immediately, 24 h or 1 week after treatments. All specimens were ground into powder and prepared for the spectrophotometric analysis. Data were subjected to two-way analysis of variance and Fisher's PLSD test at 5% significance level. The amount of wine pigments uptake by enamel submitted to bleaching treatments was statistically higher than that of control group, independently of the evaluation time. Results suggested that wine staining susceptibility was increased by bleaching treatments
    corecore