Experimental and theoretical study of combustion jet ignition

A combustion jet ignition system was developed to generate turbulent jets of combustion products containing free radicals and to discharge them as ignition sources into a combustible medium. In order to understand the ignition and the inflammation processes caused by combustion jets, the studies of the fluid mechanical properties of turbulent jets with and without combustion were conducted theoretically and experimentally. Experiments using a specially designed igniter, with a prechamber to build up and control the stagnation pressure upstream of the orifice, were conducted to investigate the formation processes of turbulent jets of combustion products. The penetration speed of combustion jets has been found to be constant initially and then decreases monotonically as turbulent jets of combustion products travel closer to the wall. This initial penetration speed to combustion jets is proportional to the initial stagnation pressure upstream of the orifice for the same stoichiometric mixture. Computer simulations by Chorin's Random Vortex Method implemented with the flame propagation algorithm for the theoretical model of turbulent jets with and without combustion were performed to study the turbulent jet flow field. In the formation processes of the turbulent jets, the large-scale eddy structure of turbulence, the so-called coherent structure, dominates the entrainment and mixing processes. The large-scale eddy structure of turbulent jets in this study is constructed by a series of vortex pairs, which are organized in the form of a staggered array of vortex clouds generating local recirculation flow patterns

Validation study of large-eddy simulations of wake stabilized reacting flows using artificial flame thickening approaches

Wake flows are the preferred mode of flame stabilization in lean premixed combustion in gas turbine engines, low NOx burners, afterburners etc. These flows exhibit inherent unsteadiness and for their numerical modeling and simulations, large eddy simulation (LES) techniques with an appropriate combustion model and reaction mechanism afford a balance between computational complexity and predictive accuracy. Before using them in practical systems, these techniques must be validated against experimental measurements in a number of canonical cases. In this work, results from LES of non-reacting and reacting flows are compared to data from a number of experiments, corresponding to the following configurations: a triangular bluff body in a rectangular duct, a backward facing step, and a cylindrical sudden expansion with swirl. The artificial flame thickening approach is applied for modeling turbulence-combustion interactions at small scales. Algebraic and equationbased efficiency function models are implemented, along with an appropriate reduced chemistry mechanism. A novel dynamic formulation for the efficiency function based on the flame-wrinkling equation that explicitly incorporates the influence of strain and time-history effects is proposed, and a detailed combustion chemistry mechanism is also used. Results show that the approaches are effective in simulating turbulent premixed combustion

A review of solar methane reforming systems

Because of the increasing demand for energy and the associated rise in greenhouse gas emissions, there is much interest in the use of renewable sources such as solar energy in electricity and fuels generation. One problem with solar energy, however, is that it is difficult to economically convert the radiation into usable energy at the desired locations and times, both daily and seasonally. One method to overcome this space-time intermittency is through the production of chemical fuels. In particular, solar reforming is a promising method for producing chemical fuels by reforming and/or water/carbon dioxide splitting. In this paper, a review of solar reforming systems is presented, as well as a comparison between these systems and a discussion on areas for potential innovation including chemical looping and membrane reactors. Moreover, a brief overview of catalysis in the context of reforming is presented

Numerical modeling of turbulent flow in a channel

Two-dimensional incompressible turbulent flow in a channel with a backward-facing step was studied numerically by Chorin's Random Vortex Method (RVM), an algorithm capable of tracing the action of elementary turbulent eddies and their cumulative effects without imposing any restrictions upon their motions. The step occurs in one side of a channel with otherwise flat, parallel walls; its height equals 1/3, 1/4 or 1/5 the width of the channel downstream. The main objective was to investigate the behavior of the large-scale turbulent eddies in a flow and the flow characteristics in the separated shear layer, the reattached zone, and the rebuilding boundary layer after reattachment. The unsteady vorticity field and the distribution of time-averaged turbulent statistics were obtained. The effects of expansion step height and initial boundary layer state were also studied. Comparisons were made with the available experimental results. The agreement is satisfactory in the velocity profiles and in the reattachment length, and fairly good in the turbulence profiles. Also a mechanism of the development of the reattaching turbulent flow was suggested by the numerical results

Predicting gas-flow distribution in pilot-scale fluidized beds using cfd simulations

Bubbling fluidized beds are used extensively in energy and chemical industries because of their excellent heat and mass transfer characteristics. Recently, CFD has been identified as a useful tool for predicting reactor performance, but application to large scales continues to be challenging because of limitations on computational resources. Given that the hydrodynamics can largely be characterized by bubbles rising through the bed, a more feasible approach for investigating large-scale reactors is to quantify bubble dynamics and specifically, gas distribution in different phases- visible bubble flow, bubble-through flow and dense-phase flow. In this study, 3D CFD simulations of bubbling fluidized beds are first conducted to establish the impact of scale (bed diameter) on the hydrodynamics. Using solids circulation and bubble statistics (1), it is established that wall effects cease to be significant in beds larger than 50 cm (bed aspect ratio less than 1). At this scale, simulations are then carried out for two distinct Geldart B particles and data is subsequently analyzed for gas-flow distribution in the bed. Bubble statistics are also compared with existing correlations and their relation to solids circulation and mixing is investigated. The physical model and numerical tool were developed and validated in previous studies (1,2), while 3D Bubble statistics are computed using MS3DATA (Multiphase Statistics using 3D Detection and Tracking Algorithm) (3). Accurate description of the gas-flow is crucial for large-scale combustor design since quantifying gas distribution will indicate both fuel rich zones as well as oxidant bypass through bubbles leading to inefficient performance. Please click Additional Files below to see the full abstract

Correspondence Between “Stable” Flame Macrostructure and Thermo-acoustic Instability in Premixed Swirl-Stabilized Turbulent Combustion

In this paper, we conduct an experimental investigation to study the link between the flame macroscale structure—or flame brush spatial distribution—and thermo-acoustic instabilities, in a premixed swirl-stabilized dump combustor. We operate the combustor with premixed methane–air in the range of equivalence ratio (φ) from the lean blowout limit to φ=0.75. First, we observe the different dynamic modes in this lean range as φ is raised. We also document the effect of φ on the flame macrostructure. Next, we examine the correspondence between dynamic mode transitions and changes in flame macrostructure. To do so, we modify the combustor length—by downstream truncation—without changing the underlying flow upstream. Thus, the resonant frequencies of the geometry are altered allowing for decoupling the heat release rate fluctuations and the acoustic feedback. Mean flame configurations in the modified combustor and for the same range of equivalence ratio are examined, following the same experimental protocol. It is found that not only the same sequence of flame macrostructures is observed in both combustors but also that the transitions occur at a similar set of equivalence ratio. In particular, the appearance of the flame in the outside recirculation zone (ORZ) in the long combustor—which occurs simultaneously with the onset of instability at the fundamental frequency—happens at similar φ when compared to the short combustor, but without being in latter case accompanied by a transition to thermo-acoustic instability. Then, we interrogate the flow field by analyzing the streamlines, mean, and rms velocities for the nonreacting flow and the different flame types. Finally, we focus on the transition of the flame to the ORZ in the acoustically decoupled case. Our analysis of this transition shows that it occurs gradually with an intermittent appearance of a flame in the ORZ and an increasing probability with φ. The spectral analysis of this phenomenon—we refer to as “ORZ flame flickering”—shows the presence of unsteady events occurring at two distinct low frequency ranges. A broad band at very low frequency in the range ∼(1 Hz–10 Hz) associated with the expansion and contraction of the inner recirculation zone (IRZ) and a narrow band centered around 28 Hz which is the frequency of rotation of the flame as it is advected by the ORZ flow.King Fahd University of Petroleum and Minerals (Grant R12-CE-10)King Abdullah University of Science and Technology (Grant KUS-110-010-01

Characterization of aggregate behaviors of torrefied biomass as a function of reaction severity

Several studies have shown that torrefaction can improve various characteristics of biomass, including grindability, flowability, and energy density, at least at the microscopic level. Furthermore, the improvements are often represented as a monotonic function of the torrefaction severity. However, the existing literature is less clear on whether or not these improvements persist at the aggregate level. This paper demonstrates that, at the aggregate level, using differently torrefied biomass in an experimental cookstove as a case study, the relationship between the improvements and torrefaction severity tells a much more complex story than a simple, monotonic correlation. Notably, by defining and measuring various cookstove performance characteristics ranging from stove temperature, effective heat output, and emission profiles, and how these characteristics vary with the severity of torrefied fuel, we conclude that, contrary to the conventional wisdom, more severe torrefaction in many cases does not always lead to more improved fuel characteristics

Transition From a Single to a Double Flame Structure in Swirling Reacting Flows: Mechanism, Dynamics, and Effect of Thermal Boundary Conditions

We examine experimentally the transition from a single flame stabilized along the inner shear layer (ISL) to a double flame stabilized along both the inner and the outer shear layers (OSL) and spreading over the outside recirculation zone (ORZ) in a fully premixed swirl-stabilized combustor. This work is mainly driven by previous studies demonstrating the link between this transition in the flame macrostructure and the onset of thermo-acoustic instabilities. Here, we examine the transition mechanism under thermo-acoustically stable conditions as well as the dominant flow and flame dynamics associated with it. In addition, we explore the role of changing the thermal boundary conditions around the ORZ and its effect on the presence or absence of the flame there. We start by analyzing the two flames bounding the transition, namely the single conical flame stabilized along the ISL (flame III) and the double conical flames with reactions taking place in the ORZ (flame IV). A dual chemiluminescence approach — using two cameras with a narrow field of view focused on the ORZ — is undertaken to track the progression of the flame as it reaches the ORZ. During the transition, the flame front, initially stabilized along the ISL, is entrained by OSL vortices close to where the turbulent jet impinges on the wall, leading to the ignition of the reactants in the ORZ and the ultimately the stabilization of the flame along the outer shear layer (OSL). This ORZ flame is also subject to extinction when the equivalence ratio (ϕ) is between values corresponding to flames III and IV. For ϕ lower than the critical transitional value, the flame kernel originating from the ISL-stabilized flame is shown to reach the ORZ but fails to grow and quickly disappears. For ϕ higher than the critical value, the flame kernel expands as it is advected by the ORZ flow and ultimately ignites the reactants recirculating in the ORZ. Sudden and extreme peak-to-peak values of the overall heat release rate are found to be concomitant with the ignition and extinction of the ORZ reactants. Finally, Different thermal boundary conditions are tested by modifying the heat flux through the combustion chamber boundary, particularly around the ORZ. We find that the transition is affected in different ways: while the transition from flame III to IV (i.e. as ϕ increases) is insensitive to these changes; flame IV persists at lower ϕ as its value is reduced when heat losses through the boundaries are diminished.Center for Clean Water and Clean Energy at MIT and KFUPM (Grant R12-CE-10

Water-Energy Nexus in Saudi Arabia

Water and energy systems have often been treated as separate "silo" systems over the entire pathway from production to consumption. However, their close interdependence requires some perspective of the water-energy nexus (WEN), especially in regions with very high water stresses combined with a myriad of rapid changes in resource production and consumption. This work provides a comprehensive analysis of the interdependence of water and energy in Saudi Arabia, including collecting data to map out energy and water consumption across the Kingdom. By combining and cross-referencing numerous data sources, this work creates the first country-wide Sankey diagram describing the interdependence of water and energy use in the Kingdom, and provides the most comprehensive mapping of power plant type and size. Additionally, this work reviews the energy and water industries, including outlining trends in population, urbanization, natural gas, oil, electricity, desalination, water use in energy production, and energy use in water production. Overall, a clear pattern has emerged: converging trends of rapid population increases, dwindling water resources, and rapidly growing desalination means that water use must be one of the primary driver of resource planning in Saudi, and plans to shift energy production to reduce GHG emissions must include water needs

Monocyte chemotactic protein-1 (MCP-1) as a predictor of prolonged urinary incontinence after radical prostatectomy

Objectives: To investigate monocyte chemotactic protein-1 (MCP-1) as a novel urinary biomarker to predict prolonged post prostatectomy incontinence. Methods: Men submitted urine samples prior to robotic radical prostatectomy. MCP-1 values were derived using an ELISA test. Pad usage at 7, 30, and 60 days were documented by patient post cards mailed when zero pads was reached. The primary outcome was defined as no incontinence pad usage at 30 days at prostatectomy. Results: After exclusions, 76 patients were included in analyses. Continence was reached by 29% (22/76), 56% (42/76), and (75/76) 98% at 7, 30, and 60 days, respectively. The average MCP-1 (p=0.258) was not different between the continent and incontinent groups. Highest quartile of MCP-1 (MCP > 166 pg/mL) and normalized MCP-1 (MCP-1/TV >0.53) noted a significant delay in continence at 30 days (p=0.050 and p=0.003). Only 26% (5/19) in the highest MCP1/TV quartile were continent, whereas 65% (37/57) of men in the 3 lower quartiles reached zero pad continence (p=0.003). In a logistic regression model the highest quartile of MCP1/TV had a significant chance of being incontinent at 30 days (OR 0.22; 95% CI 0.058-0.80; p=0.022). Conclusion: MCP-1/TV is a urinary biomarker that may predict prolonged urinary incontinence after radical prostatectomy