Observation of wave-packet propagation in the ion cyclotron range of frequencies in a tokamak plasma

Experimental observation of wave-packet propagation in the ion cyclotron range of frequencies in a tokamak plasma is reported. Studies were carried out in the Caltech Research Tokamak [Phys. Fluids 23, 614 (1980)] in a pure hydrogen plasma and in a regime where fast-wave damping was sufficiently small to permit multiple toroidal transits of the wave packet. Waves were launched by exciting a small loop antenna with a short burst of radio-frequency current and were detected with shielded magnetic probes. Probe scans revealed a large increase in wave-packet amplitude at smaller minor radii, and the packet velocity was found to be independent of radial position. Measurement of the packet transit time yielded direct information about the wave group velocity. Packet velocity was investigated as a function of the fundamental excitation frequency, plasma density, and toroidal magnetic field. Results are compared with the predictions of a cold plasma model that includes a vacuum layer at the edge

NASA/Pratt and Whitney experimental clean combustor program: Engine test results

A two-stage vorbix (vortex burning and mixing) combustor and associated fuel system components were successfully tested in an experimental JT9D engine at steady-state and transient operating conditions, using ASTM Jet-A fuel. Full-scale JT9D experimental engine tests were conducted in a phase three aircraft experimental clean combustor program. The low-pollution combustor, fuel system, and fuel control concepts were derived from phase one and phase two programs in which several combustor concepts were evaluated, refined, and optimized in a component test rig. Significant pollution reductions were achieved with the combustor which meets the performance, operating, and installation requirements of the engine

Lean, premixed, prevaporized fuel combustor conceptual design study

Four combustor concepts, designed for the energy efficient engine, utilize variable geometry or other flow modulation techniques to control the equivalence ratio of the initial burning zone. Lean conditions are maintained at high power to control oxides of nitrogen while near stoichometric conditions are maintained at low power for low CO and THC emissions. Each concept was analyzed and ranked for its potential in meeting the goals of the program. Although the primary goal of the program is a low level of nitric oxide emissions at stratospheric cruise conditions, both the ground level EPA emission standards and combustor performance and operational requirements typical of advanced subsonic aircraft engines are retained as goals as well. Based on the analytical projections made, two of the concepts offer the potential of achieving the emission goals; however, the projected operational characteristics and reliability of any concept to perform satisfactorily over an entire aircraft flight envelope would require extensive experimental substantiation before engine adaptation can be considered

ADP correspondence system: Unsolicited proposal evaluation tracking application

A complete description of a correspondence control system, designed to be used by non-ADP clerical personnel is provided. In addition to operating instructions, sufficient design and conceptual information is provided to allow use or adaption of the system in related applications. The complete COBOL program and documentation are available

Minimum mass sizing of a large low-aspect ratio airframe for flutter-free performance

A procedure for sizing an airframe for flutter-free performance is demonstrated on a large, flexible supersonic transport aircraft. The procedure is based on using a two level reduced basis or modal technique for reducing the computational cost of performing the repetitive flutter analyses. The supersonic transport aircraft exhibits complex dynamic behavior, has a well-known flutter problem and requires a large finite element model to predict the vibratory and flutter response. Flutter-free designs were produced with small mass increases relative to the wing structural weight and aircraft payload

Deflections of beam columns on multiple supports

Lateral deflections of beam columns on multiple equally spaced supports are calculated using the STAGS nonlinear structural analysis computer program. Three lateral loadings are considered, uniform, linear, and uniform over only the center bay. Two types of boundary conditions are considered at the end supports, clamped, and simple support. The effect of an initial sinusoidal imperfection are considered. Deflections in the center and end bays of the beam columns are presented as a function of applied axial compressive load. As the number of bays becomes large, the effect of boundary conditions on the deflections in the center bays diminishes. For cases involving a uniform or linearly varying load, imperfections can have a much larger effect on deflections in the center bays than can lateral pressure

Current research on shear buckling and thermal loads with PASCO: Panel Analysis and Sizing Code

The PASCO computer program to obtain the detailed dimensions of optimum stiffened composite structural panels is described. Design requirements in terms of inequality constraints can be placed on buckling loads or vibration frequencies, lamina stresses and strains, and overall panel stiffness for each of many load conditions. General panel cross sections can be treated. An analysis procedure involving a smeared orthotropic solution was investigated. The conservatism in the VIPASA solution and the danger in a smeared orthotropic solution is explored. PASCO's capability to design for thermal loadings is also described. It is emphasized that design studies illustrate the importance of the multiple load condition capability when thermal loads are present

Buckling loads for stiffened panels subjected to combined longitudinal compression and shear loadings: Results obtained with PASCO, EAL, and STAGS computer

The shear buckling analyses used in PASCO are summarized. The PASCO analyses include the basic VIPASA analysis, which is essentially exact for longitudinal and transverse loads, and a smeared orthotropic solution which was added to alleviate a shortcoming in the VIPASA analysis. Buckling results are presented for six stiffened panels loaded by combinations of longitudinal compression and shear. The buckling results were obtained with the PASCO, EAL, and STAGS computer programs. The EAL and STAGS solutions were obtained with a fine finite element mesh and provide calculations for the entire range of combinations of longitudinal compression and shear loadings

Evaluation of Federal Aviation Administration ion engine exhaust sampling rake

A FAA exhaust emissions rake was tested in the Experimental Clean Combustor Program, Phase 3 to permit comparison of the values of gaseous emissions and smoke measured by the FAA rake with those measured with the NASA Pratt and Whitney Aircraft (P and WA) rake used in the Phase 3 Experimental Clean Combustor Program and with station seven probes. The results showed that the levels of CO, THC, NOx and smoke measured by the FAA and NASA/P and WA rakes agree well at high power, but that CO emissions measured by the FAA rake were approximately 10 percent higher than those measured by the NASA/P and WA rake at low power

Buckling loads of stiffened panels subjected to combined longitudinal compression and shear: Results obtained with PASCO, EAL, and STAGS computer programs

Buckling analyses used in PASCO are summarized with emphasis placed on the shear buckling analyses. The PASCO buckling analyses include the basic VIPASA analysis, which is essentially exact for longitudinal and transverse loads, and a smeared stiffener solution, which treats a stiffened panel as an orthotropic plate. Buckling results are then presented for seven stiffened panels loaded by combinations of longitudinal compression and shear. The buckling results were obtained with the PASCO, EAL, and STAGS computer programs. The EAL and STAGS solutions were obtained with a fine finite element mesh and are very accurate. These finite element solutions together with the PASCO results for pure longitudinal compression provide benchmark calculations to evaluate other analysis procedures