Calibration of seven-hole pressure probes for use in fluid flows with large angularity

Described here is the calibration of a non-nulling, conical, seven-hole pressure probe over a large range of flow onset angles. The calibration procedure is based on the use of differential pressures to determine the three components of velocity. The method allows determination of the flow angle to within 0.5 deg and velocity magnitude to approximately 1.0 percent. Also included is an examination of the factors which limit the use of the probe, a description of the measurement chain, an error analysis, and a typical experimental result. In addition, a new general analytical model of pressure probe behavior is described and the validity of the model is demonstrated by comparing it with experimentally measured calibration data for a three-hole yaw meter and a seven-hole probe

Flow visualization study of a two-dimensional representation of the Space Shuttle launch pad configuration

The loss of the Space Shuttle Challenger was caused by the failure of the aft joint O-ring seals in its right solid rocket booster. It has been suggested by several sources that wind conditions through a reduction in temperature of the right solid rocket booster caused by the wind blowing across the cold external tank, played a role in the O-ring failure. To check the plausibility of the wind theory, an experiment was carried out in a water towing tank to visualize the flow past a two-dimensional model representing a cross section of the Space Shuttle launch configuration. The periodic formation of vortices was found to characterize the wake generated by the model. It is suggested that this organized motion in the flow is the dominant mechanism that accomplishes heat transfer from the external tank to the right solid rocket booster. Flow visualization results consisting of photographs that show instantaneous streamline patterns of the flow are presented

Wind tunnel study of an observatory dome with a circular aperture

Results of a wind tunnel test of a new concept in observatory dome design, the Fixed Shutter Dome are presented. From an aerodynamic standpoint, the new dome configuration is similar in overall shape to conventional observatory domes, with the exception of the telescope viewing aperture. The new design consists of a circular aperture of reduced area in contrast to conventional domes with rectangular or slotted openings. Wind tunnel results of a side-by-side comparison of the new dome with a conventional dome demonstrate that the mean and fluctuating velocity through the aperture and in the center of the new dome configuration are lower than those of conventional domes, thus reducing the likelihood of telescope flow-induced vibration

Analytical study of the origin and behavior of asymmetric vortices

An hypothesis advanced originally to explain computational observations is supported by theoretical considerations: The asymmetric mean flow observed on bodies of revolution at moderate to high angles of attack is the result of a convective instability of an originally symmetric flow to a time-invariant space-fixed disturbance. Additionally, the time-dependent fluctuations characteristic of the flow at higher angles of attack (up to 90 deg) are the result of an absolute instability of an originally steady flow to a small temporal disturbance of finite duration. Within a common domain, the instability mechanisms may coexist. The experimentally confirmed existence of bistable states, wherein the side-force variation with nose roll angle approaches a square-wave distribution, is attributed to the dominant influence of a pair of trailing vortices from the ogival forebody. Their existence is made possible by the appearance of foci of separation in the skin-friction line pattern beyond a critical angle of attack. The extreme sensitivity of the asymmetric flow orientation to nose geometry, demonstrated experimentally, is attributed to the presence of an indeterminate phase in the family of possible solutions for the three-dimensional wave system

A computational/experimental study of the flow around a body of revolution at angle of attack

The incompressible Navier-Stokes equations are numerically solved for steady flow around an ogive-cylinder (fineness ration 4.5) at angle of attack. The three-dimensional vortical flow is investigated with emphasis on the tip and the near wake region. The implicit, finite-difference computation is performed on the CRAY X-MP computer using the method of pseudo-compressibility. Comparisons of computational results with results of a companion towing tank experiment are presented for two symmetric leeside flow cases of moderate angles of attack. The topology of the flow is discussed and conclusions are drawn concerning the growth and stability of the primary vortices

Computational Study of Surface Tension and Wall Adhesion Effects on an Oil Film Flow Underneath an Air Boundary Layer

The fringe-imaging skin friction (FISF) technique, which was originally developed by D. J. Monson and G. G. Mateer at Ames Research Center and recently extended to 3-D flows, is the most accurate skin friction measurement technique currently available. The principle of this technique is that the skin friction at a point on an aerodynamic surface can be determined by measuring the time-rate-of-change of the thickness of an oil drop placed on the surface under the influence of the external air boundary layer. Lubrication theory is used to relate the oil-patch thickness variation to shear stress. The uncertainty of FISF measurements is estimated to be as low as 4 percent, yet little is known about the effects of surface tension and wall adhesion forces on the measured results. A modified version of the free-surface Navier-Stokes solver RIPPLE, developed at Los Alamos National Laboratories, was used to compute the time development of an oil drop on a surface under a simulated air boundary layer. RIPPLE uses the volume of fluid method to track the surface and the continuum surface force approach to model surface tension and wall adhesion effects. The development of an oil drop, over a time period of approximately 4 seconds, was studied. Under the influence of shear imposed by an air boundary layer, the computed profile of the drop rapidly changes from its initial circular-arc shape to a wedge-like shape. Comparison of the time-varying oil-thickness distributions computed using RIPPLE and also computed using a greatly simplified numerical model of an oil drop equation which does not include surface tension and wall adhesion effects) was used to evaluate the effects of surface tension on FISF measurement results. The effects of surface tension were found to be small but not necessarily negligible in some cases

Mars Ascent Vehicle Hybrid Propulsion Development

Hybrid propulsion is being investigated as a propulsion method for a possible Mars Ascent Vehicle (MAV) application. MAV is part of a proposed larger Mars Sample Return (MSR) campaign plan to bring samples from Mars to earth for examination. The Mars Ascent Vehicle would launch Mars surface samples found and packaged by the Mars 2020 mission to orbit around Mars. This version of hybrid propulsion is based on a wax based solid fuel, called SP7A, and a Mixed Oxides of Nitrogen oxidizer, MON-25. SP7 is a new fuel formulation developed by Space Propulsion Group and was modified for this application to be resistant to Mars temperature extremes and modified again to lower the regression rate to become SP7A. MON-25 was chosen for its low freezing temperature. Due to cost constraints, MON-3 was the oxidizer used during testing through 2018. In 2019, full scale hybrid testing with MON-25 commenced in Mojave, CA by Whittinghill Aerospace. One flight motor will be subjected to thermal cycling in a vacuum and later fired in a vacuum to demonstrate the proposed Liquid Injection Thrust Vector Control system performance at White Sands Test Facility (WSTF). In addition, there will be MON-25 characterization work done at Purdue University and WSTF. Additional testing of subscale and full scale motors will be conducted with MON-3 with fuel grain stress, fuel grain support and case design test objectives by Space Propulsion Group Inc. of Butte, MT. This paper documents some of the testing, issues and accomplishments with the MAV hybrid propulsion option that is being considered (along with a two-stage solid propulsion option)

Comparison of Experimental Surface and Flow Field Measurements to Computational Results of the Juncture Flow Model

Wing-body juncture flow fields on commercial aircraft configurations are challenging to compute accurately. The NASA Advanced Air Vehicle Program's juncture flow committee is designing an experiment to provide data to improve Computational Fluid Dynamics (CFD) modeling in the juncture flow region. Preliminary design of the model was done using CFD, yet CFD tends to over-predict the separation in the juncture flow region. Risk reduction wind tunnel tests were requisitioned by the committee to obtain a better understanding of the flow characteristics of the designed models. NASA Ames Research Center's Fluid Mechanics Lab performed one of the risk reduction tests. The results of one case, accompanied by CFD simulations, are presented in this paper. Experimental results suggest the wall mounted wind tunnel model produces a thicker boundary layer on the fuselage than the CFD predictions, resulting in a larger wing horseshoe vortex suppressing the side of body separation in the juncture flow region. Compared to experimental results, CFD predicts a thinner boundary layer on the fuselage generates a weaker wing horseshoe vortex resulting in a larger side of body separation

Development of a Fluid Structures Interaction Test Technique for Fabrics

Application of fluid structures interaction (FSI) computational techniques to configurations of interest to the entry, descent and landing (EDL) community is limited by two factors - limited characterization of the material properties for fabrics of interest and insufficient experimental data to validate the FSI codes. Recently ILC Dover Inc. performed standard tests to characterize the static stress-strain response of four candidate fabrics for use in EDL applications. The objective of the tests described here is to address the need for a FSI dataset for CFD validation purposes. To reach this objective, the structural response of fabrics was measured in a very simple aerodynamic environment with well controlled boundary conditions. Two test series were undertaken. The first series covered a range of tunnel conditions and the second focused on conditions that resulted in fabric panel buckling